Pasted

<<=== Plater Tab ===>>
 	Scale factors: 				[200 200 200]
 <<=== Print Settings Tab ===>>
 	-- Layers and Perimeters --
 	Layer height: 				0.20 mm
	First layer: 				0.16 mm
	Vertical perimeters: 		1
	Spiral vase: 				ENABLED <<--- this is the momst importantt!
	Top layers: 				0
	Bottom layers 				0
	Seam position:  			Aligned (doesn't matter, does it?)
 	All remaining checkboxes on this tab should be cleared.
  	-- Infill Settings --
	All settings on this tab are ignored when "Spiral Vase" is enabled.
  	-- Skirt and Brim Settings --
	Zero skirt settings
	Brim width: 				3 mm;
  	-- Support Settings --
	Settings on this tab are ignored when "Spiral Vase" eis enabled
  	-- Speed Settings --
	Perimeters: 				45 mm/s
	Small Perimeters: 			15 mm/s
	External Perimeters 		100 %
	Travel:						100 mm/s
	First layer speed:			15 mm/s
  	-- Advanced Settings --
	Default extrusion width: 	0.5 mm
	First layer:			 	110 %
  <<=== Filament Settings Tab ===>>
 	-- Filament --
 	Color choice doesn't matter
	Diameter: 					a) measure the filament diameter at least 5 points on the filament
								b) discard the highest and lower values
								c) average the rest
	Extrusion multiplier:		0.98
 	Extruder first-layer temp: 	215 ºC
	Extruder other layers temp:	210 ºC
 	Bed temp is ZERO if printing onto blue tape, 45 ºC otherwise
 	-- Cooling --
	Enable auto cooling: 		ENABLED
	Fan speed (min) 			40 %
	Fan speed (max) 			100 %
	Disable fan for n layers: 	4
	Slow down if layer time is <20 seconds
	Min print speed: 			10 mm/s
 	-- Custom G-code --
 	Start G-code: 				G28 ; home all axes
								G21 ; Set all units to millimeters
								M106 S0 ; Turn off the part cooling fan
								M83 ; Switch to relative extrusion coordinates
								G90 ; Switch to absolute motion coordinates
								M220 S100 ; Reset speed multiplier
								M221 S100 ; Reset extrusion multiplier
 								G1 Z5 F1500 ; Lift hotned
								G1 X40 Y5 F4000 ; Move to  prime line start
								G1 Z0.2 F250 ; Lower hotend
								G1 X190 E35 F540 ; Slow prime
								G1 Z5 E-2 F1500 ; Raise hotend
 	End G-code: 				M220 S100 ; Reset feedrate multiplier
								M221 S100 ; Reset extrusion multipler
 								G91 ; Relative motion coordinates
								G1 Z10 E-5 F1000 ; Lift hotend
								G90 ; Absolute motion coordinates
								G1 X5 F3000 ; Park hotend 
								G1 Y200 F1200 ;  Extend bed forward
 								M106 S0 ; Disable layer fan
								M104 S0 ; Disable hotend heater
								M140 S0 ; Disable bed heater
								M84 ; disable motors	
 <<=== Printer Settings ===>>
 	-- General -- 
	Use relative E distances: 	Enabled
	Variable layer height: 		Disabled
 	-- Nozzle --
	Nozzle diameter: 			0.4 mm (If you don't have a 0.4 mm nozzle in, that changes things, let me know)
	Min layer height 			0.16 mm
	Max layer height 			0.2 mm