Pasted

import os
from yade import pack
 
dSnorm = 5000.0 #norm of the stress increment
nbProbes = 36 #number of stress directions tested
rampIte = 20 #nb iterations to increase the stress state until the final desired stress value
stabIte = 5000 #nb iterations to stabilize sample after reaching the final stress value
key='_probing_envelope_'
 
stabilityThreshold=0.001 # leave it too low can have a super stable state, but will eat onion for waiting so long
 
 
triax=TriaxialStressController()
stickLoad=triax.strain[1]
REC=TriaxialStateRecorder()
# an array for saving stress increments and strain responses; arrays are in "numpy" extension
import numpy
probings=numpy.zeros((3,nbProbes))
 
def increment(dsr=0,dsa=1):
#   rampIte = 20
    for ite in range(rampIte):# progressivaly increase of stress state
        O.run(20, True)
        #incrementation of stress state
        triax.goal2 = initSa+dsa/rampIte*ite
        triax.goal1 = triax.goal3 = initSr+dsr/rampIte*ite
        print triax.goal1, triax.goal2, '(stress value)'
 
    # fix the stress value for stabilization at the final state
    #REC.file=('WallStresses'+key2)
    triax.goal2 = initSa+dsa
    triax.goal1 = triax.goal3 = initSr+dsr
 
    while 1:
        O.run(100, True)
        unb=unbalancedForce()
        print 'unbalanced force:',unb,' strain: ',triax.strain
        O.save('checkpoint.xml') # reload this file to check if we see mistakes
        if unb<stabilityThreshold: break
 
 
 
# loop over all the stress directions
for i in range(nbProbes):
 
    # computation of the stress direction of the current stress probe
    alphaS = 2*pi/nbProbes*(i-1)
    print 'stress probe nb:',i,' stress direction (deg): ',degrees(alphaS)
 
    # computation of the stress increment in the axial direction
    dSa = dSnorm*sin(alphaS) 
 
    # computation of the stress increment in the radial direction
    dSr = dSnorm*cos(alphaS)/sqrt(2.0)
 
    #Load the initial anisotropic state before running a new stress probe
    O.load('firstpoint.xml')
    #key2='_DIR%d'%i
    #REC.file=('WallStresses'+key2)
    triax.stressMask=7
    triax.goal2=stickLoad
    triax.goal1=triax.goal3=100000
    #We redefine the "triax" label, else it would point to inactive engine from previous simulation that is still in memory
    triax=O.engines[4]
 
    initSa=triax.goal2  #save of the initial axial stress
    initSr=triax.goal1  #save of the initial radial stress
 
    # define the final stress state to be reached
    finalSa = initSa+dSa
    finalSr = initSr+dSr
 
    #... need to active stress control in 3 directions if not yet done
#   triax.stressControl_1=triax.stressControl_2=triax.stressControl_3=True
    triax.stressMask=7  # Hien: the previous is 7, that means the stress control is on, but the following code is focus on strain control so I turn this off
 
    # fix a high value of maximum strain rate, the progressive loading will be done by progressively increasing the desired stress state at each iteration
#   triax.strainRate1=triax.strainRate2=triax.strainRate3=1000.0
#   triax.goal1=triax.goal2=triax.goal3=1000.0 #!!!!!!
    increment(dSr,dSa)
    O.wait()
#   O.save('Direction_%d.xml'%(i-1))
    os.rename('WallStresses_probing_envelope_','Dir_%d'%(i-1))