Pasted

# This file contains common pin mappings for Melzi v2.0 boards. To use
# this config, the firmware should be compiled for the AVR
# atmega1284p.
 
# Note, a number of Melzi boards are shipped with a bootloader that
# requires the following command to flash the board:
#  avrdude -p atmega1284p -c arduino -b 57600 -P /dev/ttyUSB0 -U out/klipper.elf.hex
# If the above command does not work and "make flash" does not work
# then one may need to flash a bootloader to the board - see the
# Klipper docs/Bootloaders.md file for more information.
 
# See the example.cfg file for a description of available parameters.
 
[stepper_x]
step_pin: PD7
dir_pin: PC5
enable_pin: !PD6
step_distance: .0125
endstop_pin: ^!PC2
position_endstop: 0
position_max: 220
homing_speed: 50
homing_retract_dist: 10
homing_retract_speed: 25
second_homing_speed: 10
 
[stepper_y]
step_pin: PC6
dir_pin: PC7
enable_pin: !PD6
step_distance: .0125
endstop_pin: ^!PC3
position_endstop: 0
position_max: 220
homing_speed: 50
homing_retract_dist: 10
homing_retract_speed: 25
second_homing_speed: 10
 
[stepper_z]
step_pin: PB3
dir_pin: !PB2
enable_pin: !PA5
step_distance: .0025
endstop_pin: ^!PC4
position_endstop: 0.5
position_max: 250
homing_speed: 15
homing_retract_dist: 5
homing_retract_speed: 10
second_homing_speed: 5
 
[extruder]
step_pin: PB1
dir_pin: PB0
enable_pin: !PD6
step_distance: .002
nozzle_diameter: 0.400
filament_diameter: 1.750
max_extrude_only_distance: 100
max_extrude_only_velocity: 40
pressure_advance: 0.0
pressure_advance_smooth_time: 0.04
heater_pin: PD5
min_temp: 0
min_extrude_temp: 180
max_temp: 280
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PA7
smooth_time: 2.0
control: pid
pid_Kp: 22.2
pid_Ki: 1.08
pid_Kd: 114
pid_integral_max: 1.0
 
[heater_bed]
heater_pin: PD2
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PA6
control: watermark
min_temp: 0
max_temp: 130
max_delta: 2.0
 
[fan]
pin: PB4
 
[mcu]
serial: /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0
baud: 115200 
restart_method: arduino
 
[printer]
kinematics: cartesian
max_velocity: 300
max_accel: 5000
max_z_velocity: 15
max_z_accel: 1500
max_accel_to_decel: 2000
square_corner_velocity: 5.0
 
[safe_z_home]
home_xy_position: 0,0
speed: 50
z_hop: 10
z_hop_speed: 25
move_to_previous: False
 
[virtual_sdcard]
path: ~/.octoprint/uploads
 
[force_move]
enable_force_move: True
 
[pause_resume]
recover_velocity: 50
 
[firmware_retraction]
retract_length: 1.0
retract_speed: 40
unretract_extra_length: 0.0
unretract_speed: 30
 
[include /configs/*.cfg]