[stepper_x]
step_pin: PE9
dir_pin: PF1
enable_pin: !PF2
step_distance: .0125
endstop_pin: PB10
position_endstop: 0
position_max: 500
homing_speed: 50
homing_retract_dist: 2.5
second_homing_speed: 10
[tmc2208 stepper_x]
uart_pin: PC13
microsteps: 16
interpolate: True
run_current: 0.800
hold_current: 0.500
stealthchop_threshold: 999
[stepper_y]
step_pin: PE11
dir_pin: PE8
enable_pin: !PD7
step_distance: .0125
endstop_pin: PE12
position_endstop: 0
position_max: 500
homing_speed: 50
homing_retract_dist: 2.5
second_homing_speed: 10
[tmc2208 stepper_y]
uart_pin: PE3
microsteps: 4
interpolate: True
run_current: 0.800
hold_current: 0.500
stealthchop_threshold: 999
[stepper_z]
step_pin: PE113
dir_pin: PC2
enable_pin: !PC0
step_distance: .01
endstop_pin: PG8
position_endstop: 0.5
position_min: -1
position_max: 500
homing_retract_dist: 2.5
second_homing_speed: 10
[tmc2208 stepper_z]
uart_pin: PE1
microsteps: 4
interpolate: True
run_current: 0.650
hold_current: 0.450
stealthchop_threshold: 30
[extruder]
step_pin: PE14
dir_pin: PA0
enable_pin: !PC3
step_distance: 0.010526
nozzle_diameter: 0.400
filament_diameter: 1.750
heater_pin: PB1
sensor_pin: PF3
sensor_type: EPCOS 100K B57560G104F
control: pid
max_power: 1.00
smooth_time: 1.0
pid_Kp: 18.28
pid_Ki: 1.28
pid_Kd: 65.48
min_temp: -5
max_temp: 280
pressure_advance: 0.05
pressure_advance_lookahead_time: 0.01
[tmc2208 extruder]
uart_pin: PD4
microsteps: 4
interpolate: False
run_current: 0.800
hold_current: 0.500
stealthchop_threshold: 5
[heater_bed]
heater_pin: PD12
sensor_pin: PF6 # T3
sensor_type: ATC Semitec 104GT-2
control: pid
pid_Kp: 426.68
pid_Ki: 78.92
pid_Kd: 576.71
min_temp: 0
max_temp: 130
[fan]
pin: PC8
[heater_fan fan1]
pin: PE5
[mcu]
serial: /dev/serial/by-id/usb-Klipper_Klipper_firmware_12345-if00
[printer]
kinematics: cartesian
max_velocity: 300
max_accel: 4000
max_accel_to_decel: 1500
square_corner_velocity: 4
max_z_velocity: 60
max_z_accel: 2000
[homing_override]
set_position_z: 5
gcode: G1 Z10 F500
G28
G1 Z10 F500
axes: z
[virtual_sdcard]
path: ~/.octoprint/uploads/
[force_move]
enable_force_move: True
Comments