Pasted

#define AOK_DOWN              "10100011101011101110000001011110000000010000000001000011001100001"
#define AOK_UP                "10100011101011101110000001011110000000010000000000001011111110001"
 
#define TRANSMIT_PIN             13      // We'll use digital 13 for transmitting
#define REPEAT_COMMAND           8       // How many times to repeat the same command: original remotes repeat 8 (multi) or 10 (single) times by default
#define DEBUG                    false   // Do note that if you add serial output during transmit, it will cause delay and commands may fail
 
// If you wish to use PORTB commands instead of digitalWrite, these are for Arduino Uno digital 13:
#define D13high | 0x20; 
#define D13low  & 0xDF; 
 
// Timings in microseconds (us). Get sample count by zooming all the way in to the waveform with Audacity.
// Calculate microseconds with: (samples / sample rate, usually 44100 or 48000) - ~15-20 to compensate for delayMicroseconds overhead.
// Sample counts listed below with a sample rate of 44100 Hz:
#define AOK_AGC1_PULSE                   5300  // 234 samples
#define AOK_AGC2_PULSE                   530   // 24 samples after the actual AGC bit
#define AOK_RADIO_SILENCE                5030  // 222 samples
 
#define AOK_PULSE_SHORT                  270   // 12 samples
#define AOK_PULSE_LONG                   565   // 25 samples, approx. 2 * AOK_PULSE_SHORT
 
#define AOK_COMMAND_BIT_ARRAY_SIZE       65    // Command bit count
 
const byte numChars = 32;
char receivedChars[numChars];
boolean newData = false;
 
void setup() {
  Serial.begin(9600);
  Serial.flush();
}
 
void loop() {
  recvWithEndMarker();
  showNewData();
}
 
void recvWithEndMarker() {
  static byte ndx = 0;
  char endMarker = '\n';
  char rc;
 
  while (Serial.available() > 0 && newData == false) {
    rc = Serial.read();
  
    if (rc != endMarker) {
      receivedChars[ndx] = rc;
      ndx++;
      if (ndx >= numChars) {
        ndx = numChars - 1;
      }
    } else {
      receivedChars[ndx] = '\0';
      ndx = 0;
      newData = true;
    }
  }
}
 
void showNewData() {
  if (newData == true) {
    newData = false;
 
    Serial.println(receivedChars);
 
    if (strcmp(receivedChars, "screen_up") == 0) {
      sendAOKCommand(AOK_UP);
    } else if (strcmp(receivedChars, "screen_down") == 0) {
      sendAOKCommand(AOK_DOWN);
    }
  }
}
 
void sendAOKCommand(char* command) {
  
  if (command == NULL) {
    errorLog("sendAOKCommand(): Command array pointer was NULL, cannot continue.");
    return;
  }
 
  // Prepare for transmitting and check for validity
  pinMode(TRANSMIT_PIN, OUTPUT); // Prepare the digital pin for output
  
  if (strlen(command) < AOK_COMMAND_BIT_ARRAY_SIZE) {
    errorLog("sendAOKCommand(): Invalid command (too short), cannot continue.");
    return;
  }
  if (strlen(command) > AOK_COMMAND_BIT_ARRAY_SIZE) {
    errorLog("sendAOKCommand(): Invalid command (too long), cannot continue.");
    return;
  }
  
  // Repeat the command:
  for (int i = 0; i < REPEAT_COMMAND; i++) {
    doAOKTribitSend(command);
  }
 
  // Disable output to transmitter to prevent interference with
  // other devices. Otherwise the transmitter will keep on transmitting,
  // disrupting most appliances operating on the 433.92MHz band:
  digitalWrite(TRANSMIT_PIN, LOW);
}
 
void doAOKTribitSend(char* command) {
 
  // Starting (AGC) bits:
  transmitHigh(AOK_AGC1_PULSE);
  transmitLow(AOK_AGC2_PULSE);
 
  // Transmit command:
  for (int i = 0; i < AOK_COMMAND_BIT_ARRAY_SIZE; i++) {
 
      // If current bit is 0, transmit HIGH-LOW-LOW (100):
      if (command[i] == '0') {
        transmitHigh(AOK_PULSE_SHORT);
        transmitLow(AOK_PULSE_LONG);
      }
 
      // If current bit is 1, transmit HIGH-HIGH-LOW (110):
      if (command[i] == '1') {
        transmitHigh(AOK_PULSE_LONG);
        transmitLow(AOK_PULSE_SHORT);
      }   
   }
 
  // Radio silence at the end.
  // It's better to go a bit over than under minimum required length:
  transmitLow(AOK_RADIO_SILENCE);
  
  if (DEBUG) {
    Serial.println();
    Serial.print("Transmitted ");
    Serial.print(AOK_COMMAND_BIT_ARRAY_SIZE);
    Serial.println(" bits.");
    Serial.println();
  }
}
 
void transmitHigh(int delay_microseconds) {
  digitalWrite(TRANSMIT_PIN, HIGH);
  //PORTB = PORTB D13high; // If you wish to use faster PORTB calls instead
  delayMicroseconds(delay_microseconds);
}
 
void transmitLow(int delay_microseconds) {
  digitalWrite(TRANSMIT_PIN, LOW);
  //PORTB = PORTB D13low; // If you wish to use faster PORTB calls instead
  delayMicroseconds(delay_microseconds);
}
 
void errorLog(String message) {
  Serial.println(message);
}