[probe]
pin: P1.25
x_offset: -41
y_offset: 0
z_offset: 0.998
speed: 1
samples: 7
sample_retract_dist: 1.8
lift_speed: 10
[bed_mesh]
speed: 200
horizontal_move_z: 5
mesh_min: 36,54
mesh_max: 175,200
probe_count: 9,9
mesh_pps: 3,3
algorithm: bicubic
[stepper_x]
step_pin: P2.2
dir_pin: !P2.6
enable_pin: !P2.1
step_distance: 0.05
endstop_pin: !P1.29
position_endstop: 0
position_max: 235
homing_speed: 100
homing_retract_dist: 10
second_homing_speed: 20
[tmc2208 stepper_x]
uart_pin: P1.17
microsteps: 4
run_current: 0.800
hold_current: 0.500
stealthchop_threshold: 999
[stepper_y]
step_pin: P0.19
dir_pin: P0.20
enable_pin: !P2.8
step_distance: .05
endstop_pin: !P1.27
position_endstop: 0
position_max: 300
homing_speed: 100
homing_retract_dist: 10
second_homing_speed: 20
[tmc2208 stepper_y]
uart_pin: P1.15
microsteps: 4
run_current: 0.800
hold_current: 0.500
stealthchop_threshold: 999
[stepper_z]
step_pin: P0.22
dir_pin: !P2.11
enable_pin: !P0.21
step_distance: 0.01
endstop_pin: probe:z_virtual_endstop
position_endstop: 0
position_min: -1
position_max: 250
homing_speed: 10
homing_retract_dist: 5
homing_retract_speed: 7.5
second_homing_speed: 2.5
[tmc2208 stepper_z]
uart_pin: P1.10
microsteps: 4
run_current: 0.8
hold_current: 0.250
stealthchop_threshold: 300
[extruder]
step_pin: P2.13
dir_pin: !P0.11
enable_pin: !P2.12
step_distance: .00245
nozzle_diameter: 0.400
filament_diameter: 1.750
heater_pin: P2.7
sensor_type: ATC Semitec 104GT-2
sensor_pin: P0.24
control: pid
pid_Kp: 22.2
pid_Ki: 1.08
pid_Kd: 114
min_temp: 0
max_temp: 260
min_extrude_temp: 170
[tmc2208 extruder]
uart_pin: P1.8
microsteps: 16
interpolate: false
run_current: 0.800
hold_current: 0.500
stealthchop_threshold: 0
interpolation: False
[heater_bed]
heater_pin: P2.5
sensor_type: NTC 100K beta 3950
sensor_pin: P0.23
min_temp: 0
max_temp: 120
control: pid
pid_kp: 63.041
pid_ki: 2.898
pid_kd: 342.787
[fan]
pin: P2.3
[mcu]
serial: /dev/serial/by-id/usb-Klipper_lpc1768_07700015610039AFBB20F55BC72000F5-if00
baud: 250000
[printer]
kinematics: cartesian
max_velocity: 300
max_accel: 4000
max_z_velocity: 30
max_z_accel: 750
#[safe_z_home]
#home_xy_position: 155,150
#homing_retract_dist: 15
#second_homing_speed: 25
#speed: 50
#z_hop: 5
#z_hop_speed: 15
[homing_override]
set_position_z: 5
gcode: G91
G1 Z10 F1250
G28 X
G28 Y
G90
G1 X157.5 Y117.5 F7000
G28 Z
G1 Z5 F1250
respond_msg: "Homing complete."
axes: xyz
[force_move]
enable_force_move: True
[virtual_sdcard]
path: ~/.octoprint/uploads
[pause_resume]
recover_velocity: 50
[firmware_retraction]
retract_length: 4
retract_speed: 25
unretract_extra_length: 5
unretract_speed: 35
[respond]
default_type: echo
#*# <---------------------- SAVE_CONFIG ---------------------->
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
#*#
#*# [bed_mesh default]
#*# version = 1
#*# points =
#*# -0.207500, -0.135417, -0.059167, -0.030833, -0.220417
#*# -0.034583, 0.078333, 0.131667, 0.224167, 0.082917
#*# 0.111667, 0.050000, 0.074583, 0.026667, -0.095417
#*# 0.237500, 0.025417, -0.038333, -0.231250, -0.446250
#*# 0.070417, -0.025000, -0.019167, -0.310833, -0.637500
#*# x_count = 5
#*# y_count = 5
#*# mesh_x_pps = 2
#*# mesh_y_pps = 2
#*# algo = bicubic
#*# tension = 0.2
#*# min_x = 20.0
#*# max_x = 175.0
#*# min_y = 20.0
#*# max_y = 215.0
Comments