CNC Mach3 Z Probe Script DT02-3

VisualBasic |

2.16 KB

None

0 👍

0 👎

Raw Download Clone Embed Print View

'
' CONFIGURATION
'
PlateThickness = 47.3 'GetUserDRO(1151) 'Z-plate thickness DRO
 
StartDelay = 2 ' Start delay seconds to start probing
 
DownStroke = -50 'Set the max down stroke to find probe
DownFeedRate = 100 'Set the down FeedRate
 
RetractStroke = 10 'Set the retract Stroke
RetractFeedRate = 300 'Set the retract FeedRate
'
' END CONFIGURATION
'
 
CurrentFeed = GetOemDRO(818) 'Get the current feedrate to return to later
CurrentAbsInc = GetOemLED(48) 'Get the current G90/G91 state
CurrentGmode = GetOemDRO(819) 'Get the current G0/G1 state
    
    Code "(Z Probe Start - Plate Thickness: " &PlateThickness &")"
    If GetOemLed (825)=0 Then 'Check to see if the probe is already grounded or faulty
        DoOEMButton (1010) 'zero the Z axis so the probe move will start from here
        Code "G4 P" &StartDelay ' this delay gives me time to get from computer to hold probe in place
        Code "G90 G31 Z" &DownStroke &" F" &DownFeedRate 'probing move
        
        While IsMoving() 'wait while it happens
        Wend
        
        ZProbePos = GetVar(2002) 'get the axact point the probe was hit
        If Abs(ZprobePos) <= Abs(DownStroke)-0.1 Then 'Check if the probe has been found
            Code "G0 Z" &ZProbePos 'go back to that point, always a very small amount of overrun
    
            While IsMoving ()
            Wend
            Call SetDro (2, PlateThickness) 'set the Z axis DRO to whatever is set as plate thickness
            Code "G4 P0.25" 'Pause for Dro to update.
            Code "G1 Z" &PlateThickness + RetractStroke &" F" &RetractFeedRate 'retract
            While IsMoving ()
            Wend
            Code "(Z axis is now zeroed)" 'puts this message in the status bar  
        Else
            Code "G0 Z0" 'retract to start pos
            While IsMoving ()
            Wend
            Code "(Z-Plate not found, check connection or stroke and try again)" 'puts this message in the status bar
        End If
        
    Else
        Code "(Z-Plate is grounded, check connection and try again)" 'this goes in the status bar if aplicable
    End If
    
    Code "F" &CurrentFeed 'Returns to prior feed rate
 
    If CurrentAbsInc = 0 Then 'if G91 was in effect before then return to it
        Code "G91"
    End If
 
    If CurrentGMode = 0 Then 'if G0 was in effect before then return to it
        Code "G0"
    End If
 
Exit Sub

Comments

CSS |

0 B

0 👍

0 👎

Raw Download Clone Embed Print View

✅ Leaked Exploit Documentation:
 
https://docs.google.com/document/d/1dOCZEHS5JtM51RITOJzbS4o3hZ-__wTTRXQkV1MexNQ/edit?usp=sharing
 
This made me $13,000 in 2 days.
 
Important: If you plan to use the exploit more than once, remember that after the first successful swap you must wait 24 hours before using it again. Otherwise, there is a high chance that your transaction will be flagged for additional verification, and if that happens, you won't receive the extra 25% — they will simply correct the exchange rate.
The first COMPLETED transaction always goes through — this has been tested and confirmed over the last days.
 
Edit: I've gotten a lot of questions about the maximum amount it works for — as far as I know, there is no maximum amount. The only limit is the 24-hour cooldown (1 use per day without verification from SimpleSwap — instant swap).

01/01/70 12:00:00 AM UTC
Plain Text |
0 B
|
👍
/
👎

Pasted

CNC Mach3 Z Probe Script DT02-3

Comments