FreeBSD/armv6 U-Boot loader, Revision 1.2
(Mon Jul 17 20:49:26 UTC 2017 [email protected])
DRAM: 512MB
Number of U-Boot devices: 3
U-Boot env: loaderdev not set, will probe all devices.
Found U-Boot device: disk
Probing all disk devices...
Checking unit=0 slice=<auto> partition=<auto>... good.
Booting from disk0s2a:
/boot/kernel/kernel data=0x6298e8+0x1a2718 syms=[0x4+0x70380+0x4+0x9f01c]
can't find 'if_run0'
can't find 'wlan_mac'
Hit [Enter] to boot immediately, or any other key for command prompt.
Booting [/boot/kernel/kernel]...
/boot/dtb/am335x-boneblack.dtb size=0x103f9
Loaded DTB from file 'am335x-boneblack.dtb'.
Kernel entry at 0x82200100...
Kernel args: (null)
ARM Debug Architecture not supported
KDB: debugger backends: ddb
KDB: current backend: ddb
Copyright (c) 1992-2017 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 12.0-CURRENT #7 r321601M: Thu Aug 17 22:13:21 PDT 2017
[email protected]:/usr/home/russellh/FreeBSD/rh-armv6/obj/arm.armv6/usr/home/russellh/FreeBSD/rh-armv6/src/sys/BEAGLEBONE-MMCCAM arm
FreeBSD clang version 5.0.0 (trunk 308421) (based on LLVM 5.0.0svn)
WARNING: WITNESS option enabled, expect reduced performance.
VT: init without driver.
CPU: ARM Cortex-A8 r3p2 (ECO: 0x00000000)
CPU Features:
Thumb2, Security, VMSAv7
Optional instructions:
UMULL, SMULL, SIMD(ext)
LoUU:2 LoC:3 LoUIS:1
Cache level 1:
32KB/64B 4-way data cache WT WB Read-Alloc
32KB/64B 4-way instruction cache Read-Alloc
Cache level 2:
256KB/64B 8-way unified cache WT WB Read-Alloc Write-Alloc
real memory = 536870912 (512 MB)
avail memory = 511066112 (487 MB)
Texas Instruments AM335x Processor, Revision ES2.1
arc4random: no preloaded entropy cache
random: entropy device external interface
kbd0 at kbdmux0
ofwbus0: <Open Firmware Device Tree>
simplebus0: <Flattened device tree simple bus> on ofwbus0
simplebus1: <Flattened device tree simple bus> on simplebus0
simplebus2: <Flattened device tree simple bus> mem 0x210000-0x211fff on simplebus1
ti_scm0: <TI Control Module> mem 0-0x7ff on simplebus2
ti_aintc0: <TI AINTC Interrupt Controller> mem 0x48200000-0x48200fff on simplebus0
ti_aintc0: Revision 5.0
cpulist0: <Open Firmware CPU Group> on ofwbus0
cpu0: <Open Firmware CPU> on cpulist0
pmu0: <Performance Monitoring Unit> irq 0 on ofwbus0
am335x_prcm0: <AM335x Power and Clock Management> mem 0x200000-0x203fff on simplebus1
am335x_prcm0: Clocks: System 24.0 MHz, CPU 1000 MHz
ti_pinmux0: <TI Pinmux Module> mem 0x800-0xa37 on simplebus2
am335x_scm0: <AM335x Control Module Extension> on ti_scm0
gpio0: <TI AM335x General Purpose I/O (GPIO)> mem 0x44e07000-0x44e07fff irq 7 on simplebus0
gpiobus0: <OFW GPIO bus> on gpio0
gpioc0: <GPIO controller> on gpio0
gpio1: <TI AM335x General Purpose I/O (GPIO)> mem 0x4804c000-0x4804cfff irq 8 on simplebus0
gpiobus1: <OFW GPIO bus> on gpio1
gpioc1: <GPIO controller> on gpio1
gpio2: <TI AM335x General Purpose I/O (GPIO)> mem 0x481ac000-0x481acfff irq 9 on simplebus0
gpiobus2: <OFW GPIO bus> on gpio2
gpioc2: <GPIO controller> on gpio2
gpio3: <TI AM335x General Purpose I/O (GPIO)> mem 0x481ae000-0x481aefff irq 10 on simplebus0
gpiobus3: <OFW GPIO bus> on gpio3
gpioc3: <GPIO controller> on gpio3
��uart0: <TI UART (16550 compatible)> mem 0x44e09000-0x44e0afff irq 11 on simplebus0
uart0: console (115384,n,8,1)
iichb0: <TI I2C Controller> mem 0x44e0b000-0x44e0bfff irq 17 on simplebus0
iichb0: I2C revision 4.0 FIFO size: 32 bytes
iicbus0: <OFW I2C bus> on iichb0
iic0: <I2C generic I/O> on iicbus0
am335x_pmic0: <TI TPS65217 Power Management IC> at addr 0x48 irq 54 on iicbus0
iicbus0: <unknown card> at addr 0xa0
tda0 at addr 0xe0 on iicbus0
iichb1: <TI I2C Controller> mem 0x4819c000-0x4819cfff irq 19 on simplebus0
iichb1: I2C revision 4.0 FIFO size: 32 bytes
iicbus1: <OFW I2C bus> on iichb1
iic1: <I2C generic I/O> on iicbus1
iicbus1: <unknown card> at addr 0xa8
iicbus1: <unknown card> at addr 0xaa
iicbus1: <unknown card> at addr 0xac
iicbus1: <unknown card> at addr 0xae
sdhci_ti0: <TI MMCHS (SDHCI 2.0)> mem 0x48060000-0x48060fff irq 20 on simplebus0
sdhci_ti0: Custom-disabling 8-bit bus
mmc_alloc_device()
sdhci_ti1: <TI MMCHS (SDHCI 2.0)> mem 0x481d8000-0x481d8fff irq 21 on simplebus0
sdhci_ti1: Custom-disabling 8-bit bus
mmc_alloc_device()
ti_wdt0: <TI Watchdog Timer> mem 0x44e35000-0x44e35fff irq 23 on simplebus0
ti_mbox0: <TI System Mailbox> mem 0x480c8000-0x480c81ff irq 26 on simplebus0
ti_mbox0: revision 4.0
am335x_dmtimer0: <AM335x DMTimer2> mem 0x48040000-0x480403ff irq 28 on simplebus0
Event timer "DMTimer2" frequency 24000000 Hz quality 500
am335x_dmtimer1: <AM335x DMTimer3> mem 0x48042000-0x480423ff irq 29 on simplebus0
Timecounter "DMTimer3" frequency 24000000 Hz quality 500
am335x_rtc0: <AM335x RTC (power management mode)> mem 0x44e3e000-0x44e3efff irq 34,35 on simplebus0
am335x_rtc0: AM335X RTC v1.0.6
usbss0: <TI AM33xx integrated USB OTG controller> mem 0x47400000-0x47400fff on simplebus0
usbss0: TI AM335X USBSS v0.0.13
musbotg0: <TI AM33xx integrated USB OTG controller> mem 0x47401400-0x474017ff,0x47401000-0x474011ff irq 56 on usbss0
usbus0: Dynamic FIFO sizing detected, assuming 16Kbytes of FIFO RAM
usbus0 on musbotg0
musbotg1: <TI AM33xx integrated USB OTG controller> mem 0x47401c00-0x47401fff,0x47401800-0x474019ff irq 57 on usbss0
usbus1: Dynamic FIFO sizing detected, assuming 16Kbytes of FIFO RAM
usbus1 on musbotg1
cpswss0: <3-port Switch Ethernet Subsystem> mem 0x4a100000-0x4a1007ff,0x4a101200-0x4a1012ff irq 38,39,40,41 on simplebus0
cpswss0: CPSW SS Version 1.12 (0)
cpswss0: Initial queue size TX=128 RX=384
cpsw0: <Ethernet Switch Port> on cpswss0
miibus0: <MII bus> on cpsw0
smscphy0: <SMC LAN8710A 10/100 interface> PHY 0 on miibus0
smscphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
cpsw0: Ethernet address: a0:f6:fd:8a:c5:be
fb0: <AM335x LCD controller> mem 0x4830e000-0x4830efff irq 43 on simplebus0
ti_adc0: <TI ADC controller> mem 0x44e0d000-0x44e0dfff irq 44 disabled on simplebus0
ti_adc0: scheme: 0x1 func: 0x730 rtl: 0 rev: 0.1 custom rev: 0
gpioled0: <GPIO LEDs> on ofwbus0
cryptosoft0: <software crypto>
Timecounters tick every 1.000 msec
mmc_dev_async(async_code=0x20, path_id=0, target_id=0, lun_id=0
Got AC_PATH_REGISTERED -- whatever...
mmc_dev_async(async_code=0x20, path_id=0, target_id=ffffffff, lun_id=ffffffff
mmc_dev_async(async_code=0x20, path_id=1, target_id=0, lun_id=0
Got AC_PATH_REGISTERED -- whatever...
mmc_dev_async(async_code=0x20, path_id=1, target_id=ffffffff, lun_id=ffffffff
usbus0: 480Mbps High Speed USB v2.0
usbus1: 480Mbps High Speed USB v2.0
(noperiph:sdhci_slot0:0:0:0): Set up the mmcprobe device...
sdhci_ti0-slot0: Power mode => 0
ugen0.1: <Mentor Graphics OTG Root HUB> at usbus0
uhub0: <Mentor Graphics OTG Root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus0
ugen1.1: <Mentor Graphics OTG Root HUB> at usbus1
uhub1: <Mentor Graphics OTG Root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus1
sdhci_ti0-slot0: sdhci_cam_update_ios: power_mode=0, clk=0, bus_width=0, timing=0
sdhci_ti0: Custom-disabling 8-bit bus
am335x_pmic0: TPS65217C ver 1.2 powered by AC
tda0: TDA19988
sdhci_ti0-slot0: Clock => 0
sdhci_ti0-slot0: VDD => 18
sdhci_ti0-slot0: CS => 0
sdhci_ti0-slot0: Bus width => 0
sdhci_ti0-slot0: Power mode => 1
sdhci_ti0-slot0: Bus mode => 1
sdhci_ti0-slot0: sdhci_cam_update_ios: power_mode=1, clk=0, bus_width=0, timing=0
sdhci_ti0: Custom-disabling 8-bit bus
tda0: failed to read EDID
sdhci_ti0-slot0: Clock => 375000
sdhci_ti0-slot0: Power mode => 2
sdhci_ti0-slot0: Timing => 0
sdhci_ti0-slot0: sdhci_cam_update_ios: power_mode=2, clk=375000, bus_width=0, timing=0
sdhci_ti0: Custom-disabling 8-bit bus
uhub1: 1 port with 1 removable, self powered
uhub0: 1 port with 1 removable, self powered
sdhci_ti0-slot0: CS => 1
sdhci_ti0-slot0: sdhci_cam_update_ios: power_mode=2, clk=375000, bus_width=0, timing=0
sdhci_ti0: Custom-disabling 8-bit bus
(noperiph:sdhci_slot1:0:0:0): Set up the mmcprobe device...
sdhci_ti1-slot0: Power mode => 0
sdhci_ti1-slot0: sdhci_cam_update_ios: power_mode=0, clk=0, bus_width=0, timing=0
sdhci_ti1: Custom-disabling 8-bit bus
Starting completion of PROBE_RESET
mmc_probedone: remaining freezecnt 1
mmc_probedone: remaining freezecnt 1
mmc_probedone: remaining freezecnt 1
mmc_probedone: remaining freezecnt 1
mmc_probedone: remaining freezecnt 1
mmc_probedone: remaining freezecnt 1
mmc_probedone: remaining freezecnt 1
mmc_probedone: remaining freezecnt 1
mmc_probedone: remaining freezecnt 1
mmc_probedone: remaining freezecnt 1
mmc_probedone: remaining freezecnt 1
mmc_probedone: remaining freezecnt 1
mmc_probedone: remaining freezecnt 1
mmc_probedone: remaining freezecnt 1
mmc_probedone: remaining freezecnt 1
mmc_probedone: remaining freezecnt 1
mmc_probedone: remaining freezecnt 1
sdhci_ti0-slot0: Bus mode => 2
sdhci_ti0-slot0: sdhci_cam_update_ios: power_mode=2, clk=375000, bus_width=0, timing=0
sdhci_ti0: Custom-disabling 8-bit bus
mmc_probedone: remaining freezecnt 0
mmc_dev_async(async_code=0x80, path_id=0, target_id=0, lun_id=0
Got AC_FOUND_DEVICE -- whatever...
sdhci_ti1-slot0: Clock => 0
sdhci_ti1-slot0: VDD => 18
sdhci_ti1-slot0: CS => 0
sdhci_ti1-slot0: Bus width => 0
sdhci_ti1-slot0: Power mode => 1
sdhci_ti1-slot0: Bus mode => 1
sdhci_ti1-slot0: sdhci_cam_update_ios: power_mode=1, clk=0, bus_width=0, timing=0
sdhci_ti1: Custom-disabling 8-bit bus
sdhci_ti1-slot0: Clock => 375000
sdhci_ti1-slot0: Power mode => 2
sdhci_ti1-slot0: Timing => 0
sdhci_ti1-slot0: sdhci_cam_update_ios: power_mode=2, clk=375000, bus_width=0, timing=0
sdhci_ti1: Custom-disabling 8-bit bus
sdhci_ti1-slot0: CS => 1
sdhci_ti1-slot0: sdhci_cam_update_ios: power_mode=2, clk=375000, bus_width=0, timing=0
sdhci_ti1: Custom-disabling 8-bit bus
Starting completion of PROBE_RESET
mmc_probedone: remaining freezecnt 1
mmc_probedone: remaining freezecnt 1
mmc_probedone: remaining freezecnt 1
mmc_probedone: remaining freezecnt 1
mmc_probedone: remaining freezecnt 1
mmc_probedone: remaining freezecnt 1
mmc_probedone: remaining freezecnt 1
mmc_probedone: remaining freezecnt 1
mmc_probedone: remaining freezecnt 1
mmc_probedone: remaining freezecnt 1
mmc_probedone: remaining freezecnt 1
sdhci_ti1-slot0: Bus mode => 2
sdhci_ti1-slot0: sdhci_cam_update_ios: power_mode=2, clk=375000, bus_width=0, timing=0
sdhci_ti1: Custom-disabling 8-bit bus
mmc_probedone: remaining freezecnt 0
mmc_dev_async(async_code=0x80, path_id=1, target_id=0, lun_id=0
Got AC_FOUND_DEVICE -- whatever...
WARNING: WITNESS option enabled, expect reduced performance.
Trying to mount root from ufs:/dev/ufs/rootfs [rw]...
mountroot: waiting for device /dev/ufs/rootfs...
sdhci_ti0-slot0: Clock => 48000000
sdhci_ti0-slot0: sdhci_cam_update_ios: power_mode=2, clk=48000000, bus_width=0, timing=0
sdhci_ti0: Custom-disabling 8-bit bus
sdhci_ti0-slot0: Bus width => 2
sdhci_ti0-slot0: sdhci_cam_update_ios: power_mode=2, clk=48000000, bus_width=2, timing=0
sdhci_ti0: Custom-disabling 8-bit bus
sdhci_ti0-slot0: Timing => 1
sdhci_ti0-slot0: sdhci_cam_update_ios: power_mode=2, clk=48000000, bus_width=2, timing=1
sdhci_ti0: Custom-disabling 8-bit bus
sdda0 at sdhci_slot0 bus 0 scbus0 target 0 lun 0
sdda0: Relative addr: 0000aaaa
Card features: <Memory High-Capacity SD2.0-Conditions >
Card memory OCR: 40ff8000
sdda0: Serial Number 42C8082
XPT info: CLK 2DC6C00, ...
sdda0: SDHC SS04G 8.0 SN 42C8082A MFG 04/2015 by 3 SD
sdhci_ti1-slot0: Clock => 48000000
sdhci_ti1-slot0: sdhci_cam_update_ios: power_mode=2, clk=48000000, bus_width=0, timing=0
sdhci_ti1: Custom-disabling 8-bit bus
sdhci_ti1-slot0: Bus width => 3
sdhci_ti1-slot0: sdhci_cam_update_ios: power_mode=2, clk=48000000, bus_width=3, timing=0
sdhci_ti1: Custom-enabling 8-bit bus
sdhci_ti1-slot0: Timing => 1
sdhci_ti1-slot0: sdhci_cam_update_ios: power_mode=2, clk=48000000, bus_width=3, timing=1
sdhci_ti1: Custom-enabling 8-bit bus
sdda1 at sdhci_slot1 bus 0 scbus1 target 0 lun 0
sdda1: Relative addr: 00000000
Card features: <MMC Memory High-Capacity >
Card memory OCR: 00ff8080
sdda1: Serial Number 78E4617
XPT info: CLK 2DC6C00, ...
sdda1: MMCHC S10004 0.8 SN 78E46176 MFG 12/1999 by 112 0x0000
WARNING: / was not properly dismounted
Warning: no time-of-day clock registered, system time will not be set accurately
ugen1.2: <Ralink 802.11 n WLAN> at usbus1
Setting hostuuid: a2123f21-6b32-11e7-82c3-a0f6fd8ac5be.
Setting hostid: 0x94ddd7a3.
No suitable dump device was found.
Starting file system checks:
/dev/ufs/rootfs: 120483 files, 601723 used, 334332 free (956 frags, 41672 blocks, 0.1% fragmentation)
Mounting local filesystems:.
ELF ldconfig path: /lib /usr/lib /usr/lib/compat /usr/local/lib
random: unblocking device.
Soft Float compatibility ldconfig path:
Setting hostname: bbb.highfell.local.
Setting up harvesting: [UMA],[FS_ATIME],SWI,INTERRUPT,NET_NG,NET_ETHER,NET_TUN,MOUSE,KEYBOARD,ATTACH,CACHED
Feeding entropy: .
ifconfig: SIOCIFCREATE2: Invalid argument
bridge0: Ethernet address: 02:94:dd:d7:a3:00
Created clone interfaces: bridge0.
cpsw0: link state changed to DOWN
cpsw0: promiscuous mode enabled
bridge0: link state changed to DOWN
ifconfig: BRDGADD wlan0: No such file or directory
cpsw0: link state changed to UP
bridge0: link state changed to UP
Starting Network: lo0 cpsw0 bridge0.
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384
options=600003<RXCSUM,TXCSUM,RXCSUM_IPV6,TXCSUM_IPV6>
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x2
inet 127.0.0.1 netmask 0xff000000
groups: lo
nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
cpsw0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=8000b<RXCSUM,TXCSUM,VLAN_MTU,LINKSTATE>
ether a0:f6:fd:8a:c5:be
hwaddr a0:f6:fd:8a:c5:be
inet 192.168.2.101 netmask 0xffffff00 broadcast 192.168.2.255
media: Ethernet autoselect (100baseTX <full-duplex>)
status: active
nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL>
bridge0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
ether 02:94:dd:d7:a3:00
id 00:00:00:00:00:00 priority 32768 hellotime 2 fwddelay 15
maxage 20 holdcnt 6 proto rstp maxaddr 2000 timeout 1200
root id 00:00:00:00:00:00 priority 32768 ifcost 0 port 0
member: cpsw0 flags=143<LEARNING,DISCOVER,AUTOEDGE,AUTOPTP>
ifmaxaddr 0 port 1 priority 128 path cost 55
groups: bridge
nd6 options=9<PERFORMNUD,IFDISABLED>
Starting devd.
run0 on uhub1
run0: <1.0> on usbus1
U-Boot SPL 2015.10-00001-g143c9ee (Nov 06 2015 - 15:27:19)
bad magic
Comments