PK ! ÖCZ# # $ jgaurora_a3s_miniatures_0.2mm_nozzle[general]
version = 4
name = Miniatures 0.2mm nozzle
definition = fdmprinter
[metadata]
type = quality_changes
quality_type = normal
setting_version = 20
[values]
acceleration_enabled = True
adhesion_type = brim
jerk_enabled = True
layer_height = 0.1
layer_height_0 = 0.12
magic_spiralize = False
material_bed_temperature_layer_0 = 70
minimum_polygon_circumference = 0.4
relative_extrusion = True
retraction_combing = no_outer_surfaces
smooth_spiralized_contours = False
support_enable = True
support_structure = tree
support_type = buildplate
PK !
Ӽ~Z Z 2 jgaurora_a3s_extruder_0_#2_miniatures_0.2mm_nozzle[general]
version = 4
name = Miniatures 0.2mm nozzle
definition = fdmprinter
[metadata]
type = quality_changes
quality_type = normal
intent_category = default
position = 0
setting_version = 20
[values]
acceleration_print = 300.0
bottom_layers = 7
brim_width = 4
conical_overhang_enabled = False
cool_fan_speed_0 = 50
cool_lift_head = False
cool_min_layer_time = 0
cool_min_speed = 2.0
infill_line_distance = =0 if infill_sparse_density == 0 else (infill_line_width * 100) / infill_sparse_density * (2 if infill_pattern == 'grid' else (3 if infill_pattern == 'triangles' or infill_pattern == 'trihexagon' or infill_pattern == 'cubic' or infill_pattern == 'cubicsubdiv' else (2 if infill_pattern == 'tetrahedral' or infill_pattern == 'quarter_cubic' else (1 if infill_pattern == 'cross' or infill_pattern == 'cross_3d' else (1.6 if infill_pattern == 'lightning' else 1)))))
infill_pattern = cubicsubdiv
infill_sparse_density = 35
initial_layer_line_width_factor = 105.0
inset_direction = inside_out
ironing_enabled = False
jerk_print = 5
line_width = 0.2
magic_mesh_surface_mode = normal
material_final_print_temperature = 195
material_initial_print_temperature = 203.0
material_print_temperature = 200
material_print_temperature_layer_0 = 220
min_bead_width = 0.16
min_even_wall_line_width = 0.2
min_feature_size = 0.08
min_wall_line_width = 0.2
minimum_interface_area = 0.19
minimum_roof_area = 0.03
optimize_wall_printing_order = False
retract_at_layer_change = True
retraction_amount = 6
retraction_speed = 40
skirt_line_count = 2
speed_print = 35
speed_wall = 18
speed_wall_0 = 15.0
speed_wall_x = 30.0
support_angle = 45
support_bottom_enable = False
support_interface_enable = True
support_roof_enable = True
support_tree_tip_diameter = 0.2
top_layers = 7
travel_avoid_supports = True
wall_line_count = 4
xy_offset = 0
xy_offset_layer_0 = -0.2
z_seam_type = sharpest_corner
PK ! ÖCZ# # $ € jgaurora_a3s_miniatures_0.2mm_nozzlePK !
”º~Z Z 2 €e jgaurora_a3s_extruder_0_#2_miniatures_0.2mm_nozzlePK ²
Comments