[stepper_x]
step_pin: PD7
dir_pin: PC5
enable_pin: !PD6
step_distance: .01
endstop_pin: ^!PC2
position_endstop: -30
position_max: 220
position_min: -30
homing_speed: 50
[stepper_y]
step_pin: PC6
dir_pin: PC7
enable_pin: !PD6
step_distance: .01
endstop_pin: ^!PC3
position_endstop: -8
position_min: -8
position_max: 220
homing_speed: 50
[stepper_z]
step_pin: PB3
dir_pin: !PB2
enable_pin: !PA5
step_distance: .0025
endstop_pin: ^!PC4
position_endstop: 0.5
position_max: 240
homing_speed: 20
[extruder]
step_pin: PB1
dir_pin: PB0
enable_pin: !PD6
step_distance: .0105
nozzle_diameter: 0.400
filament_diameter: 1.750
heater_pin: PD5
sensor_type: ATC Semitec 104GT-2
sensor_pin: PA7
control: pid
pid_Kp: 21
pid_Ki: 1.25
pid_Kd: 86
min_temp: 0
max_temp: 250
[heater_bed]
heater_pin: PD4
sensor_type: ATC Semitec 104GT-2
sensor_pin: PA6
control: watermark
min_temp: 0
max_temp: 130
[fan]
pin: PB4
[mcu]
serial: /dev/serial/by-id/usb-1a86_USB2.0-Serial-if00-port0
[printer]
kinematics: cartesian
max_velocity: 300
max_accel: 2000
max_z_velocity: 20
max_z_accel: 1000
[display]
lcd_type: hd44780
rs_pin: PA3
e_pin: PA2
d4_pin: PD2
d5_pin: PD3
d6_pin: PC0
d7_pin: PC1
up_pin: PA1
analog_range_up_pin: 9000, 13000
down_pin: PA1
analog_range_down_pin: 800, 1300
click_pin: PA1
analog_range_click_pin: 2000, 2500
back_pin: PA1
analog_range_back_pin: 4500, 5000
#kill_pin: PA1
#analog_range_kill_pin: 400, 600
[virtual_sdcard]
path: ~/.octoprint/uploads/
[firmware_retraction]
retract_length: 3
retract_speed: 35
unretract_extra_length: 0
unretract_speed: 35
[pause_resume]
recover_velocity: 50
[homing_override]
set_position_z: 5
gcode: G1 Z10 F500
G28
G1 Z10 F500
axes: z
### DEFAULT MENU ###
### menu main ###
[menu __main]
type: list
name: Main Menu
items:
__tune
__octoprint
__sdcard
__control
__temp
__filament
__prepare
### menu tune ###
[menu __tune]
type: list
enable: toolhead.is_printing
name: Tune
items:
.__speed
.__flow
.__offsetz
[menu __tune __speed]
type: input
name: "Speed: {1:3d}%"
parameter: gcode.speed_factor
transform:
map(0,2,0,200)
input_min: 0
input_max: 2
input_step: 0.01
realtime: true
gcode: M220 S{1:d}
[menu __tune __flow]
type: input
name: "Flow: {1:3d}%"
parameter: gcode.extrude_factor
transform:
map(0,2,0,200)
input_min: 0
input_max: 2
input_step: 0.01
realtime: true
gcode: M221 S{1:d}
[menu __tune __offsetz]
type: input
name: "Offset Z:{0:05.3f} "
parameter: gcode.homing_zpos
input_min: -5
input_max: 5
input_step: 0.005
realtime: true
gcode: SET_GCODE_OFFSET Z={0:.3f} MOVE=1
### menu octoprint ###
[menu __octoprint]
type: list
name: OctoPrint
items:
.__pause
.__resume
.__abort
[menu __octoprint __pause]
type: command
enable: toolhead.is_printing
name: Pause printing
action: respond action:pause
gcode:
[menu __octoprint __resume]
type: command
enable: !toolhead.is_printing
name: Resume printing
action: respond action:resume
gcode:
[menu __octoprint __abort]
type: command
enable: toolhead.is_printing
name: Abort printing
action: respond action:cancel
gcode:
### menu virtual sdcard ###
[menu __sdcard]
type: vsdcard
name: SD Card
items:
.__start
.__resume
.__pause
[menu __sdcard __start]
type: command
enable: !toolhead.is_printing
name: Start printing
gcode: M24
[menu __sdcard __resume]
type: command
enable: toolhead.is_printing
name: Resume printing
gcode: M24
[menu __sdcard __pause]
type: command
enable: toolhead.is_printing
name: Pause printing
gcode: M25
### menu control ###
[menu __control]
type: list
name: Control
items:
.__home
.__homez
.__homexy
.__move_10mm
.__move_1mm
.__move_01mm
.__disable
.__fanonoff
.__fanspeed
.__caselightonoff
.__caselightpwm
[menu __control __home]
type: command
name: Home All
gcode: G28
enable: !toolhead.is_printing
[menu __control __homez]
type: command
enable: !toolhead.is_printing
name: Home Z
gcode: G28 Z
[menu __control __homexy]
type: command
enable: !toolhead.is_printing
name: Home X/Y
gcode: G28 X Y
[menu __control __disable]
type: command
name: Disable steppers
gcode:
M84
M18
[menu __control __fanonoff]
type: input
enable: fan.is_enabled
name: Fan {1:3s}
parameter: fan.speed
transform:
choose('OFF','ON')
choose(0,255)
input_min: 0
input_max: 1
input_step: 1
gcode: M106 S{2:d}
[menu __control __fanspeed]
type: input
enable: fan.is_enabled
name: Fan speed: {1:3d}%
parameter: fan.speed
transform:
map(0,1,0,100)
map(0,1,0,255)
input_min: 0
input_max: 1
input_step: 0.01
gcode: M106 S{2:d}
[menu __control __caselightonoff]
type: input
enable: output_pin.caselight.is_enabled
name: Case light: {1:3s}
parameter: output_pin.caselight.value
transform:
choose('OFF','ON')
choose(0,1)
input_min: 0
input_max: 1
input_step: 1
gcode: SET_PIN PIN=caselight VALUE={2}
[menu __control __caselightpwm]
type: input
enable: output_pin.caselight.is_enabled
name: Case light: {0:4.0%}
parameter: output_pin.caselight.value
input_min: 0.0
input_max: 1.0
input_step: 0.01
gcode: SET_PIN PIN=caselight VALUE={0:.2f}
### menu move 10mm ###
[menu __control __move_10mm]
type: list
enable: !toolhead.is_printing
name: Move 10mm
items:
.__axis_z
.__axis_x, .__axis_y
.__axis_e
[menu __control __move_10mm __axis_x]
type: input
name: "X:{0:05.1f} "
parameter: gcode.move_xpos
input_min: 0
input_max: 200.0
input_step: 10.0
gcode:
G90
G1 X{0:.1f} F2400
[menu __control __move_10mm __axis_y]
type: input
name: "Y:{0:05.1f} "
parameter: gcode.move_ypos
input_min: 0
input_max: 200.0
input_step: 10.0
gcode:
G90
G1 Y{0:.1f} F2400
[menu __control __move_10mm __axis_z]
type: input
enable: !toolhead.is_printing
name: "Move Z:{0:05.1f}"
parameter: gcode.move_zpos
input_min: 0
input_max: 200.0
input_step: 10.0
gcode:
G90
G1 Z{0:.1f} F240
[menu __control __move_10mm __axis_e]
type: input
enable: !toolhead.is_printing
name: "Move E:{0:+06.1f}"
parameter: 0
input_min: -50.0
input_max: 50.0
input_step: 10.0
gcode:
M83
G1 E{0:.1f} F240
### menu move 1mm ###
[menu __control __move_1mm]
type: list
enable: !toolhead.is_printing
name: Move 1mm
items:
.__axis_z
.__axis_x, .__axis_y
.__axis_e
[menu __control __move_1mm __axis_x]
type: input
name: "X:{0:05.1f} "
parameter: gcode.move_xpos
input_min: 0
input_max: 200.0
input_step: 1.0
gcode:
G90
G1 X{0:.1f} F2400
[menu __control __move_1mm __axis_y]
type: input
name: "Y:{0:05.1f} "
parameter: gcode.move_ypos
input_min: 0
input_max: 200.0
input_step: 1.0
gcode:
G90
G1 Y{0:.1f} F2400
[menu __control __move_1mm __axis_z]
type: input
enable: !toolhead.is_printing
name: "Move Z:{0:05.1f}"
parameter: gcode.move_zpos
input_min: 0
input_max: 200.0
input_step: 1.0
gcode:
G90
G1 Z{0:.1f} F240
[menu __control __move_1mm __axis_e]
type: input
enable: !toolhead.is_printing
name: "Move E:{0:+06.1f}"
parameter: 0
input_min: -50.0
input_max: 50.0
input_step: 1.0
gcode:
M83
G1 E{0:.1f} F240
### menu move 0.1mm ###
[menu __control __move_01mm]
type: list
enable: !toolhead.is_printing
name: Move 0.1mm
items:
.__axis_z
.__axis_x, .__axis_y
.__axis_e
[menu __control __move_01mm __axis_x]
type: input
name: "X:{0:05.1f} "
parameter: gcode.move_xpos
input_min: 0
input_max: 200.0
input_step: 0.1
gcode:
G90
G1 X{0:.1f} F2400
[menu __control __move_01mm __axis_y]
type: input
name: "Y:{0:05.1f} "
parameter: gcode.move_ypos
input_min: 0
input_max: 200.0
input_step: 0.1
gcode:
G90
G1 Y{0:.1f} F2400
[menu __control __move_01mm __axis_z]
type: input
enable: !toolhead.is_printing
name: "Move Z:{0:05.1f}"
parameter: gcode.move_zpos
input_min: 0
input_max: 200.0
input_step: 0.1
gcode:
G90
G1 Z{0:.1f} F240
[menu __control __move_01mm __axis_e]
type: input
enable: !toolhead.is_printing
name: "Move E:{0:+06.1f}"
parameter: 0
input_min: -50.0
input_max: 50.0
input_step: 0.1
gcode:
M83
G1 E{0:.1f} F240
### menu temperature ###
[menu __temp]
type: list
name: Temperature
items:
.__hotend0_current, .__hotend0_target
.__hotend1_current, .__hotend1_target
.__hotbed_current, .__hotbed_target
.__preheat_pla
.__preheat_abs
.__cooldown
[menu __temp __hotend0_current]
type: item
enable: extruder.is_enabled
name: "Ex0:{0:4.0f} T"
parameter: extruder.temperature
[menu __temp __hotend0_target]
type: input
enable: extruder.is_enabled
name: "{0:4.0f}"
parameter: extruder.target
input_min: 0
input_max: 250
input_step: 1
input_step2: 10
gcode: M104 T0 S{0:.0f}
[menu __temp __hotend1_current]
type: item
enable: extruder1.is_enabled
name: "Ex1:{0:4.0f} T"
parameter: extruder1.temperature
[menu __temp __hotend1_target]
type: input
enable: extruder1.is_enabled
name: "{0:4.0f}"
parameter: extruder1.target
input_min: 0
input_max: 250
input_step: 1
input_step2: 10
gcode: M104 T1 S{0:.0f}
[menu __temp __hotbed_current]
type: item
enable: heater_bed.is_enabled
name: "Bed:{0:4.0f} T"
parameter: heater_bed.temperature
[menu __temp __hotbed_target]
type: input
enable: heater_bed.is_enabled
name: "{0:4.0f}"
parameter: heater_bed.target
input_min: 0
input_max: 130
input_step: 1
input_step2: 10
gcode: M140 S{0:.0f}
[menu __temp __preheat_pla]
type: list
name: Preheat PLA
items:
.__all
.__hotend
.__hotbed
[menu __temp __preheat_pla __all]
type: command
enable: extruder.is_enabled,heater_bed.is_enabled
name: Preheat all
gcode:
M140 S60
M104 S200
[menu __temp __preheat_pla __hotend]
type: command
enable: extruder.is_enabled
name: Preheat hotend
gcode: M104 S200
[menu __temp __preheat_pla __hotbed]
type: command
enable: heater_bed.is_enabled
name: Preheat hotbed
gcode: M140 S60
[menu __temp __preheat_abs]
type: list
name: Preheat ABS
items:
.__all
.__hotend
.__hotbed
[menu __temp __preheat_abs __all]
type: command
enable: extruder.is_enabled,heater_bed.is_enabled
name: Preheat all
gcode:
M140 S110
M104 S245
[menu __temp __preheat_abs __hotend]
type: command
enable: extruder.is_enabled
name: Preheat hotend
gcode: M104 S245
[menu __temp __preheat_abs __hotbed]
type: command
enable: heater_bed.is_enabled
name: Preheat hotbed
gcode: M140 S110
[menu __temp __cooldown]
type: list
name: Cooldown
items:
.__all
.__hotend
.__hotbed
[menu __temp __cooldown __all]
type: command
enable: extruder.is_enabled,heater_bed.is_enabled
name: Cooldown all
gcode:
M104 S0
M140 S0
[menu __temp __cooldown __hotend]
type: command
enable: extruder.is_enabled
name: Cooldown hotend
gcode: M104 S0
[menu __temp __cooldown __hotbed]
type: command
enable: heater_bed.is_enabled
name: Cooldown hotbed
gcode: M140 S0
### menu filament ###
[menu __filament]
type: list
name: Filament
items:
__temp __hotend0_current, __temp __hotend0_target
.__unload
.__load
.__feed
[menu __filament __load]
type: command
name: Load Filament
gcode:
M83
G1 E50 F1000
G1 E50 F1000
G1 E50 F1000
G1 E50 F1000
G1 E50 F300
G1 E50 F300
M82
[menu __filament __unload]
type: command
name: Unload Filament
gcode:
M83
G1 E-50 F1000
G1 E-50 F1000
G1 E-50 F1000
G1 E-50 F1000
G1 E-50 F1800
G1 E-50 F1800
G1 E-50 F1800
G1 E-50 F1800
M82
[menu __filament __feed]
type: input
name: Feed: {0:.1f}
parameter: 0
input_step: 0.1
gcode:
M83
G1 E{0:.1f} F30
### menu prepare ###
[menu __prepare]
type: list
enable: !toolhead.is_printing
name: Prepare
items:
.__delta_calib
.__bedprobe
.__hotend_pid_tuning
.__hotbed_pid_tuning
.__host_restart
.__firmware_restart
[menu __prepare __host_restart]
type: command
enable: !toolhead.is_printing
name: Restart host
gcode: RESTART
[menu __prepare __firmware_restart]
type: command
enable: !toolhead.is_printing
name: Restart FW
gcode: FIRMWARE_RESTART
[menu __prepare __delta_calib]
type: command
enable: !toolhead.is_printing
name: Delta calibrate
gcode: DELTA_CALIBRATE
[menu __prepare __bedprobe]
type: command
enable: !toolhead.is_printing
name: Bed probe
gcode: PROBE
[menu __prepare __hotend_pid_tuning]
type: command
enable: !toolhead.is_printing, extruder.is_enabled
name: Tune Hotend PID
gcode: PID_CALIBRATE HEATER=extruder TARGET=210 WRITE_FILE=1
[menu __prepare __hotbed_pid_tuning]
type: command
enable: !toolhead.is_printing, heater_bed.is_enabled
name: Tune Hotbed PID
gcode: PID_CALIBRATE HEATER=heater_bed TARGET=60 WRITE_FILE=1
Comments