/*
  Reads temperature from HT11 sensor and writes to SD card
  SD card read/write via LC Technology SD Module (www.lctech-inc.com)

 * SD card attached to SPI bus as follows:
 ** MOSI - pin 11
 ** MISO - pin 12
 ** SCK  - pin 13
 ** CS   - pin 4
 ** GND  - GND
 ** +3.3 - 3.3V

 HT11 Sensor is wired per below. Note: with checked openings facing you,
 pin 1 is to the left.
 ** PIN 1 - 3.3V or 5V
 ** PIN 2 - Data (to pins attached below (probably 2)
 ** PIN 3 - NC
 ** PIN 4 - Ground

 This example code is in the public domain.

 */
#define SOFTWARE_SPI 1
#define ITERATIONS 25

#include <SD.h>		// SD Card library
#include <dht11.h>	// DHT111 temperature probe Library

dht11 DHT11;


File myFile;

void shutdown()
{
	// add you emergency shutdown code here
	while (1); // endless loop
}

void setup()
{
// Open serial communications and wait for port to open:
	Serial.begin(9600);
	DHT11.attach(2);
	Serial.println("DHT11 TEST PROGRAM ");
	Serial.print("LIBRARY VERSION: ");
	Serial.println(DHT11LIB_VERSION);


	Serial.print("Initializing SD card...");
	// On the Ethernet Shield, CS is pin 4. It's set as an output by default.
	// Note that even if it's not used as the CS pin, the hardware SS pin
	// (10 on most Arduino boards, 53 on the Mega) must be left as an output
	// or the SD library functions will not work.
	pinMode(10, OUTPUT);

	if (!SD.begin(4)) {
		Serial.println("initialization failed!");
		return;
	}

	Serial.println("initialization done.");

	// open the file. note that only one file can be open at a time,
	// so you have to close this one before opening another.
	myFile = SD.open("temps.txt", FILE_WRITE);

	// if the file opened okay, write to it:
	if (!myFile) {
	    // if the file didn't open, print an error:
	    Serial.println("error opening file - Halting system");
	    shutdown();
	}

        Serial.print("Test limited to ");
        Serial.print(ITERATIONS, DEC);
        Serial.println(" temperature readings");
        Serial.println("File on SD created, temperature tests will now start");
}

void loop()
{
	int n, chk;

        myFile.println("Test of LC Technology SD Module and DFRobot DHT11 Temperature & Humidity Sensor");
        myFile.print("Test limited to ");
        myFile.print(ITERATIONS, DEC);
        myFile.println(" temperature readings");
	for (n = 0; n < ITERATIONS; n++) {
		chk = DHT11.read();
		Serial.print("Sensor read: ");
		myFile.print("\nSensor read: ");

		switch (chk) {
		case 0:
			Serial.println("OK");
			myFile.println("OK");
			myFile.print("Humidity (%): ");
			myFile.println((float)DHT11.humidity, DEC);

			myFile.print("Temperature (");
			myFile.print((char)176);        // Print degree symbol
			myFile.print("C): ");
			myFile.println((float)DHT11.temperature, DEC);

			myFile.print("Temperature (");
			myFile.print((char)176);
			myFile.print("F): ");
			myFile.println(DHT11.fahrenheit(), DEC);

			myFile.print("Temperature (");
			myFile.print((char)176);
			myFile.print("K): ");
			myFile.println(DHT11.kelvin(), DEC);

			myFile.print("Dew Point (");
			myFile.print((char)176);
			myFile.print("C): ");
			myFile.println(DHT11.dewPoint(), DEC);

			myFile.print("Dew PointFast (");
			myFile.print((char)176);
			myFile.print("C): ");
			myFile.println(DHT11.dewPointFast(), DEC);
			break;

		case -1:
			Serial.println("Checksum error");
			Serial.println("Checksum error");
			break;

		case -2:
			Serial.println("Time out error");
			myFile.println("Time out error");
			break;

		default:
			Serial.println("Unknown error");
			myFile.println("Unknown error");
			break;
		}
		delay(2000);	// 2-second pause
	}
        Serial.println("Test Complete - Halting system");
        myFile.close();
	shutdown();
}