[probe]
pin: 						P1.25
x_offset: 					-41
y_offset: 					0
z_offset:	 				0.998
speed: 						1
samples: 					7
sample_retract_dist: 		1.8
lift_speed:					10

[bed_mesh]
speed: 						200
horizontal_move_z: 			5
mesh_min: 					36,54
mesh_max: 					175,200
probe_count: 				9,9
mesh_pps: 					3,3
algorithm: 					bicubic

[stepper_x]
step_pin: 					P2.2
dir_pin: 					!P2.6
enable_pin: 				!P2.1
step_distance: 				0.05
endstop_pin: 				!P1.29
position_endstop: 			0
position_max: 				235
homing_speed: 				100
homing_retract_dist: 		10
second_homing_speed:		20

[tmc2208 stepper_x]
uart_pin: 					P1.17
microsteps: 				4
run_current: 				0.800
hold_current: 				0.500
stealthchop_threshold: 		999

[stepper_y]
step_pin:					P0.19
dir_pin: 					P0.20
enable_pin: 				!P2.8
step_distance: 				.05
endstop_pin: 				!P1.27
position_endstop: 			0
position_max: 				300
homing_speed: 				100
homing_retract_dist:		10
second_homing_speed: 		20

[tmc2208 stepper_y]
uart_pin: 					P1.15
microsteps: 				4
run_current:			    0.800
hold_current: 				0.500
stealthchop_threshold: 		999

[stepper_z]
step_pin: 					P0.22
dir_pin: 					!P2.11
enable_pin: 				!P0.21
step_distance: 				0.01
endstop_pin: 				probe:z_virtual_endstop
position_endstop: 			0
position_min: 				-1
position_max: 				250
homing_speed: 				10
homing_retract_dist:		5
homing_retract_speed: 		7.5
second_homing_speed: 		2.5

[tmc2208 stepper_z]
uart_pin:					P1.10
microsteps: 				4
run_current: 				0.8
hold_current: 				0.250
stealthchop_threshold: 		300

[extruder]
step_pin: 					P2.13
dir_pin: 					!P0.11
enable_pin: 				!P2.12
step_distance: 				.00245
nozzle_diameter: 			0.400
filament_diameter: 			1.750
heater_pin: 				P2.7
sensor_type: 				ATC Semitec 104GT-2
sensor_pin: 				P0.24
control: 					pid
pid_Kp: 					22.2
pid_Ki: 					1.08
pid_Kd: 					114
min_temp:					0
max_temp:					260
min_extrude_temp: 			170

[tmc2208 extruder]
uart_pin: 					P1.8
microsteps: 				16
interpolate: 				false
run_current: 				0.800
hold_current: 				0.500
stealthchop_threshold: 		0
interpolation: 				False

[heater_bed]
heater_pin: 				P2.5
sensor_type: 				NTC 100K beta 3950
sensor_pin: 				P0.23
min_temp: 					0
max_temp: 					120
control: 					pid
pid_kp: 					63.041
pid_ki: 					2.898
pid_kd: 					342.787

[fan]
pin:						P2.3

[mcu]
serial: 					/dev/serial/by-id/usb-Klipper_lpc1768_07700015610039AFBB20F55BC72000F5-if00
baud: 						250000

[printer]
kinematics: 				cartesian
max_velocity: 				300
max_accel: 					4000
max_z_velocity: 			30
max_z_accel: 				750

#[safe_z_home]
#home_xy_position: 			155,150
#homing_retract_dist: 		15
#second_homing_speed:		25
#speed: 					50
#z_hop: 					5
#z_hop_speed: 				15

[homing_override]
set_position_z:				5
gcode:						G91
       						G1 Z10 F1250 
       						G28 X 
       						G28 Y 
       						G90 
       						G1 X157.5 Y117.5 F7000 
       						G28 Z 
       						G1 Z5 F1250
respond_msg:				"Homing complete."
axes: 						xyz

[force_move]
enable_force_move: 			True

[virtual_sdcard]
path: 						~/.octoprint/uploads

[pause_resume]
recover_velocity:			50

[firmware_retraction]
retract_length: 			4
retract_speed: 				25
unretract_extra_length: 	5
unretract_speed: 			35

[respond]
default_type: 				echo

#*# <---------------------- SAVE_CONFIG ---------------------->
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
#*#
#*# [bed_mesh default]
#*# version = 1
#*# points =
#*# 	-0.207500, -0.135417, -0.059167, -0.030833, -0.220417
#*# 	-0.034583, 0.078333, 0.131667, 0.224167, 0.082917
#*# 	0.111667, 0.050000, 0.074583, 0.026667, -0.095417
#*# 	0.237500, 0.025417, -0.038333, -0.231250, -0.446250
#*# 	0.070417, -0.025000, -0.019167, -0.310833, -0.637500
#*# x_count = 5
#*# y_count = 5
#*# mesh_x_pps = 2
#*# mesh_y_pps = 2
#*# algo = bicubic
#*# tension = 0.2
#*# min_x = 20.0
#*# max_x = 175.0
#*# min_y = 20.0
#*# max_y = 215.0