=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2015.09.28 18:43:19 =~=~=~=~=~=~=~=~=~=~=~= †!UÒššŠÂ’j BT : 11:35:50 Sep 7 2015 PMU:rn5t618 DC01 v:1100, 0x[36]: 18 -> 28 DC02 v:1150, 0x[37]: 18 -> 2c DC03 v:1500, 0x[38]: 38 -> 48 LDO01 v:2900, 0x[4c]: 4e -> 50 LDO02 v:1800, 0x[4d]: 24 -> 24 LDO03 v:1800, 0x[4e]: 30 -> 30 LDO04 v:2850, 0x[4f]: 4e -> 4e LDO05 v:1800, 0x[50]: 24 -> 24 LDO0a v:2700, 0x[56]: 28 -> 28 LDO0b v:900, 0x[57]: 00 -> 00 CPU clock is 1200MHz CPU type: M8 DDR info: 2GB(auto) @ 792MHz(1T) DDR channel: DDR 0 + DDR 1 DDR init use : 11897 us HHH Boot From SPI ucl decompress...pass 0x12345678 Boot from internal device 1st SPI TE : 403797 System Started U-boot(m8_k200_v1@t8) (Sep 07 2015 - 11:35:45) clr h-ram DRAM: 2 GiB relocation Offset is: 6feb0000 show partition table: part: 0, name : logo, size : 2000000 part: 1, name : recovery, size : 2000000 part: 2, name : misc, size : 2000000 part: 3, name : boot, size : 2000000 part: 4, name : system, size : 40000000 part: 5, name : cache, size : 20000000 part: 6, name : data, size : end aml_card_type=0x100 MMC: [mmc_register] add mmc dev_num=0, port=1, if_type=6 [mmc_register] add mmc dev_num=1, port=2, if_type=6 SDIO Port B: 0, SDIO Port C: 1 PMU fault status: reg[0x9A] = 0x1d LSI version:03, OTP version:06 PMU type:RN5T618 register usb cfg[0][1] = 7ff68014 register usb cfg[2][0] = 7ff6b93c NAND: SPI BOOT: boot_device_flag 0 Nand PHY driver Version: 2.01.001.0004 (c) 2013 Amlogic Inc. amlnf_phy_init : amlnf init flag 0 NAND device id: 2c 64 44 4b a9 0 0 0 detect NAND device: B revision NAND 8GiB MT29F64G08CBABA nand chip ce mask 1 AML_NAND_NEW_OOB : new oob bus_cycle=6, bus_timing=8,system=3.9ns,flash->T_REA =16,flash->T_RHOH=15 NAND CKECK : arg nbbt: arg_valid= 1, valid_blk_addr = 7, valid_page_addr = 0 nand block at blk 4 is bad nand block at blk 5 is bad NAND CKECK : arg ncnf: arg_valid= 1, valid_blk_addr = 9, valid_page_addr = 0 nand block at blk 4 is bad nand block at blk 5 is bad NAND CKECK : arg nkey: arg_valid= 1, valid_blk_addr = 6, valid_page_addr = 5 i=0,register --- nand_key driver_version in nand 1.01.001.0004 nand partition table changed: misc partition->size: from 1000000 to 2000000 nand dev nfcode : nr_partitions num changed from 5 to 2 nand configs confirm failed nand configs confirm failed shipped_bbt_valid_ops and ret:-19 get device configs failed and ret:ffffffed nandphy_init failed and ret=0xffffffed get_boot_device_flag: init_ret 1 get_boot_device_flag SPI BOOT: nand init success, change the device_boot_flag to 4 : spi+nand SPI BOOT,spi_env_relocate_spec : env_relocate_spec 53 SF: Detected MX25L1605D with page size 256, total 2 MiB SPI NOR Flash have write protect!!! set_storage_device_flag: store 4 nand get nftl dev boot failed nftl_dev be NULL nand cmd read failed nand cmd store failed Err imgread(L123):Fail to read 0x1000B from part[boot] at offset 0 check dts: FDT_ERR_BADMAGIC, load default vpu parameters vpu driver detect cpu type: m8 vpu clk_level = 7 set vpu clk: 364300000Hz, readback: 364300000Hz(0x700) Net: Meson_Ethernet init suspend firmware done. (ret:0) cvbs trimming.1.v5: 0xa0, 0x0 charging wipe_data=successful wipe_cache=successful has.accelerometer = false cvbsmode = 576cvbs hdmimode = 1080p outputmode = 1080p Using default environment set_storage_device_flag: store 0 set_storage_device_flag: set store to 4 SPI BOOT,spi_saveenv : saveenv 97 Erasing SPI flash...Writing to SPI flash...done Saving Environment to SPI Flash... SPI BOOT,spi_saveenv : saveenv 97 Erasing SPI flash...Writing to SPI flash...done reboot_mode=charging TV mode 1080p selected. mode = 8 vic = 16 set HDMI vic: 16 config HPLL config HPLL done reconfig packet setting done nand get nftl dev logo failed nftl_dev be NULL nand cmd read failed nand cmd store failed Err imgread(L519):Fail to read 0x2000B from part[logo] at offset 0 There is no valid bmp file at the given address bmp scale: mode=1080p , x=0, y=0, w=1920, h=1080 Hit Enter key to stop autoboot -- : 1  0 exit abortboot: 0 current storer:nand_key key save is auto select storer(nand or emmc) write key code version3_flush:708,prov->write:7fed9a10 nand detect bad blk at 4 chip 0 nand detect bad blk at 4 chip 0 buf should never be NULL nand write failed buf should never be NULL nand write failed rewrite! nand detect bad blk at 4 chip 0 buf should never be NULL nand write failed buf should never be NULL nand write failed rewrite! nand detect bad blk at 4 chip 0 nand detect bad blk at 5 chip 0 nand detect bad blk at 4 chip 0 buf should never be NULL nand write failed buf should never be NULL nand write failed rewrite! nand detect bad blk at 4 chip 0 nand detect bad blk at 5 chip 0 nand detect bad blk at 5 chip 0 buf should never be NULL nand write failed test block 3 times, operating environment maybe wrong! NAND SAVE : arg nkey faild at blk:5 save key error,nand_key_write write key ok!! Booting... error: image data is not a fdt key_unify_init:364,unify key config table parse fail Err key(L47):fail in key_drv_init nand get nftl dev boot failed nftl_dev be NULL nand cmd read failed nand cmd store failed Err imgread(L323):Fail to read 0x100000B from part[boot] at offset 0 Wrong Image Format for bootm command ERROR: can't get kernel image! enter recovery sdio_detect return 1 sdio debug board detected, no sd card in (Re)start USB(0)... USB0: dwc_usb driver version: 2.94 6-June-2012 USB (1) peri reg base: c1108820 USB (1) use clock source: XTAL input USB (1) base addr: 0xc90c0000 Force id mode: Host dwc_otg: Highspeed device found ! scanning bus 0 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found ** Invalid boot device ** nand get nftl dev recovery failed nftl_dev be NULL nand cmd read failed nand cmd store failed Err imgread(L323):Fail to read 0x100000B from part[recovery] at offset 0 no recovery in flash m8_k200_v1#