U-Boot SPL 2026.01-rc2 (Nov 22 2025 - 14:49:09 +0000) phytec_eeprom_data_init: EEPROM is not flashed. Prototype? phytec_eeprom_data_setup_fallback: init failed. Trying fall back address 0x59 SOM: PCM-070-0F3243I.A3 PCB Rev.: 2 WDT: Started watchdog@30280000 with servicing every 1000ms (60s timeout) SEC0: RNG instantiated Trying to boot from BOOTROM Boot Stage: Primary boot image offset 0x8000, pagesize 0x200, ivt offset 0x0 NOTICE: Do not release JR0 to NS as it can be used by HAB NOTICE: BL31: v2.13.0(release):v2.13.0-dirty NOTICE: BL31: Built : 10:24:05, May 22 2025 U-Boot 2026.01-rc2 (Nov 22 2025 - 14:49:09 +0000) CPU: NXP i.MX8MP[8] Rev1.1 A53 at 1200 MHz CPU: Industrial temperature grade (-40C to 105C) at 52C Model: PHYTEC phyBOARD-Pollux i.MX8MP DRAM: 2 GiB phytec_eeprom_data_init: EEPROM is not flashed. Prototype? phytec_eeprom_data_setup_fallback: init failed. Trying fall back address 0x59 Core: 250 devices, 33 uclasses, devicetree: separate WDT: Started watchdog@30280000 with servicing every 1000ms (60s timeout) MMC: FSL_SDHC: 1, FSL_SDHC: 2 Loading Environment from MMC... *** Warning - bad CRC, using default environment Reading from MMC(1)... In: serial@30860000 Out: serial@30860000 Err: serial@30860000 SEC0: RNG instantiated Net: eth0: ethernet@30be0000 Hit any key to stop autoboot: 0 Scanning for bootflows in all bootdevs Seq Method State Uclass Part Name Filename --- ----------- ------ -------- ---- ------------------------ ---------------- Scanning bootdev 'mmc@30b60000.bootdev': Scanning bootdev 'mmc@30b50000.bootdev': 0 script ready mmc 1 mmc@30b50000.bootdev.part /boot.scr.uimg ** Booting bootflow 'mmc@30b50000.bootdev.part_1' with script 14854716 bytes read in 157 ms (90.2 MiB/s) Working FDT set to 40480000 ## Loading kernel (any) from FIT Image at 40480000 ... Using 'conf-imx8mp-phyboard-pollux-rdk.dtb' configuration Verifying Hash Integrity ... OK Trying 'kernel-1' kernel subimage Description: Linux kernel Type: Kernel Image Compression: gzip compressed Data Start: 0x40480130 Data Size: 14782147 Bytes = 14.1 MiB Architecture: AArch64 OS: Linux Load Address: 0x5a080000 Entry Point: 0x5a080000 Hash algo: sha256 Hash value: b58f714bc0dec3c1162f88de80b57f273b67b80577caa0f0e1178a75010d4a70 Verifying Hash Integrity ... sha256+ OK ## Loading fdt (any) from FIT Image at 40480000 ... Using 'conf-imx8mp-phyboard-pollux-rdk.dtb' configuration Verifying Hash Integrity ... OK Trying 'fdt-imx8mp-phyboard-pollux-rdk.dtb' fdt subimage Description: Flattened Device Tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x41299114 Data Size: 71208 Bytes = 69.5 KiB Architecture: AArch64 Load Address: 0x48000000 Hash algo: sha256 Hash value: 794fdd4ea99dd47fb9c243f2ed5654dc779de21d71b8ce091c0c198487604e18 Verifying Hash Integrity ... sha256+ OK Loading fdt from 0x41299114 to 0x48000000 Booting using the fdt blob at 0x48000000 Working FDT set to 48000000 Uncompressing Kernel Image to 5a080000 Moving Image from 0x5a080000 to 0x5a200000, end=0x5ca30000 Loading Device Tree to 000000007ae97000, end 000000007aeab627 ... OK Working FDT set to 7ae97000 Device nor0 not found! Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034] [ 0.000000] Linux version 6.16.11-yocto-standard-g42ddd61a7bce (oe-user@oe-host) (aarch64-phytec-linux-gcc (GCC) 15.2.0, GNU ld (GNU Binutils) 2.45.0.20250908) #1 SMP PREEMPT Mon Oct 6 13:50:41 UTC 2025 [ 0.000000] KASLR enabled [ 0.000000] Machine model: PHYTEC phyBOARD-Pollux i.MX8MP [ 0.000000] efi: UEFI not found. [ 0.000000] earlycon: ec_imx6q0 at MMIO 0x0000000030860000 (options '') [ 0.000000] printk: legacy bootconsole [ec_imx6q0] enabled [ 0.000000] OF: reserved mem: 0x000000007fc00000..0x000000007fffffff (4096 KiB) nomap non-reusable optee_shm@7fc00000 [ 0.000000] OF: reserved mem: 0x000000007e000000..0x000000007fbfffff (28672 KiB) nomap non-reusable optee_core@7e000000 [ 0.000000] NUMA: Faking a node at [mem 0x0000000040000000-0x00000000bfffffff] [ 0.000000] NODE_DATA(0) allocated [mem 0xbfbb7240-0xbfbb98bf] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000040000000-0x00000000bfffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000040000000-0x000000007dffffff] [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000bfffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x00000000bfffffff] [ 0.000000] On node 0, zone DMA: 8192 pages in unavailable ranges [ 0.000000] cma: Reserved 32 MiB at 0x00000000bba00000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: Trusted OS migration not required [ 0.000000] psci: SMC Calling Convention v1.5 [ 0.000000] percpu: Embedded 25 pages/cpu s62616 r8192 d31592 u102400 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] CPU features: kernel page table isolation forced ON by KASLR [ 0.000000] CPU features: detected: Kernel page table isolation (KPTI) [ 0.000000] CPU features: detected: ARM erratum 845719 [ 0.000000] alternatives: applying boot alternatives [ 0.000000] Kernel command line: console=ttymxc0,115200 earlycon= root=/dev/mmcblk1p2 rootwait rw [ 0.000000] printk: log buffer data + meta data: 131072 + 458752 = 589824 bytes [ 0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes, linear) [ 0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes, linear) [ 0.000000] software IO TLB: SWIOTLB bounce buffer size adjusted to 1MB [ 0.000000] software IO TLB: area num 4. [ 0.000000] software IO TLB: mapped [mem 0x00000000bb600000-0x00000000bb800000] (2MB) [ 0.000000] Fallback order for Node 0: 0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 516096 [ 0.000000] Policy zone: DMA [ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=512 to nr_cpu_ids=4. [ 0.000000] Trampoline variant of Tasks RCU enabled. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] RCU Tasks: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=4. [ 0.000000] RCU Tasks Trace: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=4. [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode [ 0.000000] GICv3: 160 SPIs implemented [ 0.000000] GICv3: 0 Extended SPIs implemented [ 0.000000] Root IRQ handler: gic_handle_irq [ 0.000000] GICv3: GICv3 features: 16 PPIs [ 0.000000] GICv3: GICD_CTRL.DS=0, SCR_EL3.FIQ=1 [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000038880000 [ 0.000000] ITS: No ITS available, not enabling LPIs [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000] arch_timer: cp15 timer(s) running at 8.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x1d854df40, max_idle_ns: 440795202120 ns [ 0.000000] sched_clock: 56 bits at 8MHz, resolution 125ns, wraps every 2199023255500ns [ 0.010077] Console: colour dummy device 80x25 [ 0.012584] Calibrating delay loop (skipped), value calculated using timer frequency.. 16.00 BogoMIPS (lpj=32000) [ 0.022846] pid_max: default: 32768 minimum: 301 [ 0.027544] LSM: initializing lsm=capability [ 0.031872] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.039208] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.049020] rcu: Hierarchical SRCU implementation. [ 0.051922] rcu: Max phase no-delay instances is 1000. [ 0.057352] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level [ 0.068838] EFI services will not be available. [ 0.070773] smp: Bringing up secondary CPUs ... [ 0.075562] Detected VIPT I-cache on CPU1 [ 0.075627] GICv3: CPU1: found redistributor 1 region 0:0x00000000388a0000 [ 0.075665] CPU1: Booted secondary processor 0x0000000001 [0x410fd034] [ 0.076257] Detected VIPT I-cache on CPU2 [ 0.076307] GICv3: CPU2: found redistributor 2 region 0:0x00000000388c0000 [ 0.076328] CPU2: Booted secondary processor 0x0000000002 [0x410fd034] [ 0.076846] Detected VIPT I-cache on CPU3 [ 0.076895] GICv3: CPU3: found redistributor 3 region 0:0x00000000388e0000 [ 0.076916] CPU3: Booted secondary processor 0x0000000003 [0x410fd034] [ 0.077030] smp: Brought up 1 node, 4 CPUs [ 0.131706] SMP: Total of 4 processors activated. [ 0.136418] CPU: All CPU(s) started at EL2 [ 0.140569] CPU features: detected: 32-bit EL0 Support [ 0.145694] CPU features: detected: 32-bit EL1 Support [ 0.150865] CPU features: detected: CRC32 instructions [ 0.156025] CPU features: detected: PMUv3 [ 0.160081] alternatives: applying system-wide alternatives [ 0.166954] Memory: 1943236K/2064384K available (18624K kernel code, 5354K rwdata, 12868K rodata, 3264K init, 755K bss, 83944K reserved, 32768K cma-reserved) [ 0.180433] devtmpfs: initialized [ 0.194152] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.201136] posixtimers hash table entries: 2048 (order: 3, 32768 bytes, linear) [ 0.208620] futex hash table entries: 1024 (65536 bytes on 1 NUMA nodes, total 64 KiB, linear). [ 0.217954] 2G module region forced by RANDOMIZE_MODULE_REGION_FULL [ 0.223630] 0 pages in range for non-PLT usage [ 0.223635] 514000 pages in range for PLT usage [ 0.228304] pinctrl core: initialized pinctrl subsystem [ 0.241342] DMI not present or invalid. [ 0.244965] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.249719] DMA: preallocated 256 KiB GFP_KERNEL pool for atomic allocations [ 0.256216] DMA: preallocated 256 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations [ 0.264259] DMA: preallocated 256 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations [ 0.272964] thermal_sys: Registered thermal governor 'step_wise' [ 0.272975] thermal_sys: Registered thermal governor 'power_allocator' [ 0.277269] cpuidle: using governor menu [ 0.287901] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.294569] ASID allocator initialised with 32768 entries [ 0.302910] Serial: AMBA PL011 UART driver [ 0.314142] /soc@0: Fixed dependency cycle(s) with /soc@0/bus@30000000/efuse@30350000/unique-id@8 [ 0.320289] /soc@0/etm@28440000: Fixed dependency cycle(s) with /funnel [ 0.327005] /soc@0/etm@28540000: Fixed dependency cycle(s) with /funnel [ 0.333583] /soc@0/etm@28640000: Fixed dependency cycle(s) with /funnel [ 0.340232] /soc@0/etm@28740000: Fixed dependency cycle(s) with /funnel [ 0.346855] /soc@0/funnel@28c03000: Fixed dependency cycle(s) with /soc@0/etf@28c04000 [ 0.354819] /soc@0/funnel@28c03000: Fixed dependency cycle(s) with /funnel [ 0.361730] /soc@0/etf@28c04000: Fixed dependency cycle(s) with /soc@0/etr@28c06000 [ 0.369437] /soc@0/etf@28c04000: Fixed dependency cycle(s) with /soc@0/funnel@28c03000 [ 0.377420] /soc@0/etr@28c06000: Fixed dependency cycle(s) with /soc@0/etf@28c04000 [ 0.385851] /soc@0/bus@32c00000/display-controller@32e90000: Fixed dependency cycle(s) with /soc@0/bus@32c00000/blk-ctrl@32ec0000/bridge@5c [ 0.397780] /soc@0/bus@32c00000/blk-ctrl@32ec0000/bridge@5c: Fixed dependency cycle(s) with /soc@0/bus@32c00000/display-controller@32e90000 [ 0.410720] /soc@0/interrupt-controller@38800000: Fixed dependency cycle(s) with /soc@0/interrupt-controller@38800000 [ 0.421742] /funnel: Fixed dependency cycle(s) with /soc@0/etm@28440000 [ 0.427705] /soc@0/etm@28440000: Fixed dependency cycle(s) with /funnel [ 0.434393] /funnel: Fixed dependency cycle(s) with /soc@0/etm@28540000 [ 0.440998] /soc@0/etm@28540000: Fixed dependency cycle(s) with /funnel [ 0.447686] /funnel: Fixed dependency cycle(s) with /soc@0/etm@28640000 [ 0.454284] /soc@0/etm@28640000: Fixed dependency cycle(s) with /funnel [ 0.460995] /funnel: Fixed dependency cycle(s) with /soc@0/etm@28740000 [ 0.467587] /soc@0/etm@28740000: Fixed dependency cycle(s) with /funnel [ 0.474315] /funnel: Fixed dependency cycle(s) with /soc@0/funnel@28c03000 [ 0.481129] /soc@0/funnel@28c03000: Fixed dependency cycle(s) with /soc@0/etf@28c04000 [ 0.489051] /soc@0/funnel@28c03000: Fixed dependency cycle(s) with /funnel [ 0.496109] /soc@0/funnel@28c03000: Fixed dependency cycle(s) with /soc@0/etf@28c04000 [ 0.503954] /soc@0/etf@28c04000: Fixed dependency cycle(s) with /soc@0/etr@28c06000 [ 0.511631] /soc@0/etf@28c04000: Fixed dependency cycle(s) with /soc@0/funnel@28c03000 [ 0.519708] /soc@0/etf@28c04000: Fixed dependency cycle(s) with /soc@0/etr@28c06000 [ 0.527352] /soc@0/etr@28c06000: Fixed dependency cycle(s) with /soc@0/etf@28c04000 [ 0.540754] imx8mp-pinctrl 30330000.pinctrl: initialized IMX pinctrl driver [ 0.545801] /soc@0/bus@30000000/efuse@30350000: Fixed dependency cycle(s) with /soc@0/bus@30000000/clock-controller@30380000 [ 0.558638] /soc@0/bus@30000000/efuse@30350000: Fixed dependency cycle(s) with /soc@0/bus@30000000/clock-controller@30380000 [ 0.568482] /soc@0/bus@30000000/clock-controller@30380000: Fixed dependency cycle(s) with /soc@0/interrupt-controller@38800000 [ 0.594510] /soc@0/bus@32c00000/display-controller@32e90000: Fixed dependency cycle(s) with /soc@0/bus@32c00000/blk-ctrl@32ec0000/bridge@5c [ 0.604407] /soc@0/bus@32c00000/blk-ctrl@32ec0000/bridge@5c: Fixed dependency cycle(s) with /soc@0/bus@32c00000/display-controller@32e90000 [ 0.617831] /soc@0/bus@32c00000/display-controller@32e90000: Fixed dependency cycle(s) with /soc@0/bus@32c00000/blk-ctrl@32ec0000/bridge@5c [ 0.630205] /soc@0/bus@32c00000/blk-ctrl@32ec0000/bridge@5c: Fixed dependency cycle(s) with /soc@0/bus@32c00000/display-controller@32e90000 [ 0.651841] /soc@0/bus@32c00000/blk-ctrl@32ec0000/bridge@5c: Fixed dependency cycle(s) with /panel-lvds [ 0.658563] /panel-lvds: Fixed dependency cycle(s) with /soc@0/bus@32c00000/blk-ctrl@32ec0000/bridge@5c [ 0.672305] HugeTLB: allocation took 0ms with hugepage_allocation_threads=1 [ 0.676465] HugeTLB: allocation took 0ms with hugepage_allocation_threads=1 [ 0.683462] HugeTLB: registered 1.00 GiB page size, pre-allocated 0 pages [ 0.690280] HugeTLB: 0 KiB vmemmap can be freed for a 1.00 GiB page [ 0.696580] HugeTLB: registered 32.0 MiB page size, pre-allocated 0 pages [ 0.703402] HugeTLB: 0 KiB vmemmap can be freed for a 32.0 MiB page [ 0.709705] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages [ 0.716527] HugeTLB: 0 KiB vmemmap can be freed for a 2.00 MiB page [ 0.722832] HugeTLB: registered 64.0 KiB page size, pre-allocated 0 pages [ 0.729652] HugeTLB: 0 KiB vmemmap can be freed for a 64.0 KiB page [ 0.738293] ACPI: Interpreter disabled. [ 0.744083] iommu: Default domain type: Translated [ 0.746043] iommu: DMA domain TLB invalidation policy: strict mode [ 0.752610] SCSI subsystem initialized [ 0.756459] usbcore: registered new interface driver usbfs [ 0.761578] usbcore: registered new interface driver hub [ 0.766900] usbcore: registered new device driver usb [ 0.773717] pps_core: LinuxPPS API ver. 1 registered [ 0.776939] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.786137] PTP clock support registered [ 0.790205] EDAC MC: Ver: 3.0.0 [ 0.793792] scmi_core: SCMI protocol bus registered [ 0.799548] FPGA manager framework [ 0.801611] Advanced Linux Sound Architecture Driver Initialized. [ 0.808727] vgaarb: loaded [ 0.810815] clocksource: Switched to clocksource arch_sys_counter [ 0.816737] VFS: Disk quotas dquot_6.6.0 [ 0.820441] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.827558] pnp: PnP ACPI: disabled [ 0.838126] NET: Registered PF_INET protocol family [ 0.840325] IP idents hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 0.849141] tcp_listen_portaddr_hash hash table entries: 1024 (order: 2, 16384 bytes, linear) [ 0.856245] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.863986] TCP established hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 0.872041] TCP bind hash table entries: 16384 (order: 7, 524288 bytes, linear) [ 0.879717] TCP: Hash tables configured (established 16384 bind 16384) [ 0.885945] UDP hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.892660] UDP-Lite hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.899959] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.905887] RPC: Registered named UNIX socket transport module. [ 0.911408] RPC: Registered udp transport module. [ 0.916128] RPC: Registered tcp transport module. [ 0.920848] RPC: Registered tcp-with-tls transport module. [ 0.926364] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.932848] PCI: CLS 0 bytes, default 64 [ 0.940705] kvm [1]: nv: 566 coarse grained trap handlers [ 0.943756] kvm [1]: IPA Size Limit: 40 bits [ 0.951281] kvm [1]: GICv3: no GICV resource entry [ 0.953228] kvm [1]: disabling GICv2 emulation [ 0.957722] kvm [1]: GIC system register CPU interface enabled [ 0.963581] kvm [1]: vgic interrupt IRQ9 [ 0.967519] kvm [1]: Hyp nVHE mode initialized successfully [ 0.974466] Initialise system trusted keyrings [ 0.977800] workingset: timestamp_bits=42 max_order=19 bucket_order=0 [ 0.984316] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.990109] NFS: Registering the id_resolver key type [ 0.994993] Key type id_resolver registered [ 0.999173] Key type id_legacy registered [ 1.003213] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 1.009936] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 1.017554] 9p: Installing v9fs 9p2000 file system support [ 1.077713] Key type asymmetric registered [ 1.078985] Asymmetric key parser 'x509' registered [ 1.083908] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) [ 1.091306] io scheduler mq-deadline registered [ 1.095856] io scheduler kyber registered [ 1.099908] io scheduler bfq registered [ 1.121930] ledtrig-cpu: registered to indicate activity on CPUs [ 1.162296] SoC: i.MX8MP revision 1.1 [ 1.212869] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 1.221942] 30860000.serial: ttymxc0 at MMIO 0x30860000 (irq = 15, base_baud = 1500000) is a IMX [ 1.228026] printk: console [ttymxc0] enabled [ 1.228026] printk: console [ttymxc0] enabled [ 1.236640] printk: legacy bootconsole [ec_imx6q0] disabled [ 1.236640] printk: legacy bootconsole [ec_imx6q0] disabled [ 1.251921] 30890000.serial: ttymxc1 at MMIO 0x30890000 (irq = 16, base_baud = 5000000) is a IMX [ 1.253063] msm_serial: driver initialized [ 1.253759] SuperH (H)SCI(F) driver initialized [ 1.254165] STM32 USART driver initialized [ 1.265689] loop: module loaded [ 1.267516] megasas: 07.734.00.00-rc1 [ 1.273922] spi-nor spi0.0: supply vcc not found, using dummy regulator [ 1.286546] thunder_xcv, ver 1.0 [ 1.286599] thunder_bgx, ver 1.0 [ 1.286637] nicpf, ver 1.0 [ 1.289227] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version [ 1.289235] hns3: Copyright (c) 2017 Huawei Corporation. [ 1.289292] hclge is initializing [ 1.289323] e1000: Intel(R) PRO/1000 Network Driver [ 1.289326] e1000: Copyright (c) 1999-2006 Intel Corporation. [ 1.289367] e1000e: Intel(R) PRO/1000 Network Driver [ 1.289369] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 1.289410] igb: Intel(R) Gigabit Ethernet Network Driver [ 1.289416] igb: Copyright (c) 2007-2014 Intel Corporation. [ 1.289453] igbvf: Intel(R) Gigabit Virtual Function Network Driver [ 1.289457] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 1.290071] sky2: driver version 1.30 [ 1.292740] VFIO - User Level meta-driver version: 0.3 [ 1.298988] usbcore: registered new interface driver usb-storage [ 1.305160] i2c_dev: i2c /dev entries driver [ 1.323642] sdhci: Secure Digital Host Controller Interface driver [ 1.323652] sdhci: Copyright(c) Pierre Ossman [ 1.325498] Synopsys Designware Multimedia Card Interface Driver [ 1.327957] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.333801] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping .... [ 1.335759] usbcore: registered new interface driver usbhid [ 1.335767] usbhid: USB HID core driver [ 1.351754] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 (0,8000003f) counters available [ 1.354714] nvmem imx-ocotp0: cell mac-address raw len 6 unaligned to nvmem word size 4 [ 1.354729] nvmem imx-ocotp0: cell mac-address raw len 6 unaligned to nvmem word size 4 [ 1.355066] /soc@0: Fixed dependency cycle(s) with /soc@0/bus@30000000/efuse@30350000 [ 1.358293] optee: probing for conduit method. [ 1.358318] optee: revision 4.7 (86846f4fdf14f25b) [ 1.358875] mmc2: SDHCI controller on 30b60000.mmc [30b60000.mmc] using ADMA [ 1.359865] optee: dynamic shared memory is enabled [ 1.360752] random: crng init done [ 1.360772] optee: initialized driver [ 1.367848] NET: Registered PF_PACKET protocol family [ 1.367901] 8021q: 802.1Q VLAN Support v1.8 [ 1.367949] 9pnet: Installing 9P2000 support [ 1.368006] Key type dns_resolver registered [ 1.368195] NET: Registered PF_VSOCK protocol family [ 1.381344] registered taskstats version 1 [ 1.381485] Loading compiled-in X.509 certificates [ 1.392759] Demotion targets for Node 0: null [ 1.427767] mmc2: new HS400 Enhanced strobe MMC card at address 0001 [ 1.428395] i2c i2c-0: using pinctrl states for GPIO recovery [ 1.428472] i2c i2c-0: using generic GPIOs for recovery [ 1.428560] mmcblk2: mmc2:0001 DG4008 7.28 GiB [ 1.429319] i2c i2c-0: IMX I2C adapter registered [ 1.430442] mmcblk2boot0: mmc2:0001 DG4008 4.00 MiB [ 1.430922] i2c i2c-1: using pinctrl states for GPIO recovery [ 1.430992] i2c i2c-1: using generic GPIOs for recovery [ 1.431481] i2c i2c-1: IMX I2C adapter registered [ 1.432239] mmcblk2boot1: mmc2:0001 DG4008 4.00 MiB [ 1.434110] mmcblk2rpmb: mmc2:0001 DG4008 4.00 MiB, chardev (234:0) [ 1.439633] nxp-pca9450 0-0025: pca9450bc probed. [ 1.454736] /panel-lvds: Fixed dependency cycle(s) with /soc@0/bus@32c00000/blk-ctrl@32ec0000/bridge@5c [ 1.454844] /soc@0/bus@32c00000/display-controller@32e90000: Fixed dependency cycle(s) with /soc@0/bus@32c00000/blk-ctrl@32ec0000/bridge@5c [ 1.454922] /soc@0/bus@32c00000/blk-ctrl@32ec0000/bridge@5c: Fixed dependency cycle(s) with /panel-lvds [ 1.454992] /soc@0/bus@32c00000/blk-ctrl@32ec0000/bridge@5c: Fixed dependency cycle(s) with /soc@0/bus@32c00000/display-controller@32e90000 [ 1.484847] fec 30be0000.ethernet eth0: registered PHC device 0 [ 1.501117] sdhci-esdhc-imx 30b50000.mmc: Got CD GPIO [ 1.503580] imx6q-pcie 33800000.pcie: host bridge /soc@0/pcie@33800000 ranges: [ 1.503654] imx6q-pcie 33800000.pcie: IO 0x001ff80000..0x001ff8ffff -> 0x0000000000 [ 1.503680] imx6q-pcie 33800000.pcie: MEM 0x0018000000..0x001fefffff -> 0x0018000000 [ 1.503782] imx6q-pcie 33800000.pcie: config reg[1] 0x1ff00000 == cpu 0x1ff00000 [ 1.503782] ; no fixup was ever needed for this devicetree [ 1.510315] clk: Disabling unused clocks [ 1.514097] PM: genpd: Disabling unused power domains [ 1.514154] ALSA device list: [ 1.514160] No soundcards found. [ 1.539414] mmc1: SDHCI controller on 30b50000.mmc [30b50000.mmc] using ADMA [ 1.711452] imx6q-pcie 33800000.pcie: iATU: unroll T, 4 ob, 4 ib, align 64K, limit 16G [ 1.940899] mmc1: new UHS-I speed SDR104 SDXC card at address 59b4 [ 1.941907] mmcblk1: mmc1:59b4 GD2S5 119 GiB [ 1.944667] mmcblk1: p1 p2 [ 2.671274] imx6q-pcie 33800000.pcie: Phy link never came up [ 2.671697] imx6q-pcie 33800000.pcie: PCI host bridge to bus 0000:00 [ 2.671710] pci_bus 0000:00: root bus resource [bus 00-ff] [ 2.671719] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 2.671726] pci_bus 0000:00: root bus resource [mem 0x18000000-0x1fefffff] [ 2.671766] pci 0000:00:00.0: [16c3:abcd] type 01 class 0x060400 PCIe Root Port [ 2.671791] pci 0000:00:00.0: BAR 0 [mem 0x00000000-0x000fffff] [ 2.671799] pci 0000:00:00.0: ROM [mem 0x00000000-0x0000ffff pref] [ 2.671807] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 2.671816] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff] [ 2.671825] pci 0000:00:00.0: bridge window [mem 0x00000000-0x000fffff] [ 2.671836] pci 0000:00:00.0: bridge window [mem 0x00000000-0x000fffff pref] [ 2.671885] pci 0000:00:00.0: supports D1 [ 2.671890] pci 0000:00:00.0: PME# supported from D0 D1 D3hot D3cold [ 2.674912] pci 0000:00:00.0: BAR 0 [mem 0x18000000-0x180fffff]: assigned [ 2.674925] pci 0000:00:00.0: ROM [mem 0x18100000-0x1810ffff pref]: assigned [ 2.674935] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 2.674948] pci_bus 0000:00: resource 4 [io 0x0000-0xffff] [ 2.674954] pci_bus 0000:00: resource 5 [mem 0x18000000-0x1fefffff] [ 2.675617] pcieport 0000:00:00.0: PME: Signaling with IRQ 204 [ 2.675994] pcieport 0000:00:00.0: AER: enabled with IRQ 204 [ 2.703322] EXT4-fs (mmcblk1p2): mounted filesystem e308576d-719f-483d-b1d4-58f9ba6df8e3 r/w with ordered data mode. Quota mode: none. [ 2.703418] VFS: Mounted root (ext4 filesystem) on device 179:98. [ 2.703762] devtmpfs: mounted [ 2.704861] Freeing unused kernel memory: 3264K [ 2.704965] Run /sbin/init as init process [ 2.850655] systemd[1]: System time advanced to timestamp on /var/lib/systemd/timesync/clock: Mon 2025-11-24 14:06:50 UTC [ 2.939780] NET: Registered PF_INET6 protocol family [ 2.940596] Segment Routing with IPv6 [ 2.940624] In-situ OAM (IOAM) with IPv6 [ 2.975031] systemd[1]: systemd 257.8 running in system mode (+PAM -AUDIT -SELINUX -APPARMOR -IMA +IPE -SMACK +SECCOMP -GCRYPT -GNUTLS -OPENSSL +ACL +BLKID -CURL -ELFUTILS -FIDO2 -IDN2 -IDN -IPTC +KMOD -LIBCRYPTSETUP -LIBCRYPTSETUP_PLUGINS +LIBFDISK -PCRE2 -PWQUALITY -P11KIT -QRENCODE -TPM2 -BZIP2 +LZ4 -XZ -ZLIB -ZSTD -BPF_FRAMEWORK -BTF +XKBCOMMON -UTMP -SYSVINIT -LIBARCHIVE) [ 2.975082] systemd[1]: Detected architecture arm64. Welcome to The ampliPHY Distribution BSP-Yocto-Ampliphy-i.MX8MP-master-devel! [ 3.032893] systemd[1]: Hostname set to . [ 3.067879] systemd[1]: Using hardware watchdog 'imx2+ watchdog', version 0, device /dev/watchdog0 [ 3.067931] systemd[1]: Watchdog running with a hardware timeout of 1min. [ 3.433015] systemd[1]: Queued start job for default target Multi-User System. [ 3.471792] systemd[1]: Created slice Slice /system/getty. [ OK ] Created slice Slice /system/getty. [ OK ] Created slice[ 3.488679] systemd[1]: Created slice Slice /system/modprobe. Slice /system/modprobe. [ 3.509155] systemd[1]: Created slice Slice /system/serial-getty. [ OK ] Created slice Slice /system/serial-getty. [ 3.529010] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. [ 3.547734] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password Requests to Console Directory Watch. [ 3.571425] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password Requests to Wall Directory Watch. [ 3.595527] systemd[1]: Expecting device /dev/bootdev... Expecting device /dev/bootdev... [ 3.611464] systemd[1]: Expecting device /dev/ttymxc0... Expecting device /dev/ttymxc0... [ 3.627563] systemd[1]: Reached target NFS client services. [ OK ] Reached target NFS client services. [ 3.647528] systemd[1]: Reached target Path Units. [ OK ] Reached target Path Units. [ 3.663547] systemd[1]: Reached target Preparation for Remote File Systems. [ OK ] Reached target Preparation for Remote File Systems. [ 3.683516] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. [ 3.703546] systemd[1]: Reached target Slice Units. [ OK ] Reached target Slice Units. [ 3.719559] systemd[1]: Reached target Swaps. [ OK ] Reached target Swaps. [ OK ] Listening on [ 3.783547] systemd[1]: Listening on RPCbind Server Activation Socket. RPCbind Server Activation Socket. [ 3.807213] systemd[1]: Reached target RPC Port Mapper. [ OK ] Reached target RPC Port Mapper. [ OK ] Listening on [ 3.832312] systemd[1]: Listening on Credential Encryption/Decryption. Credential Encryption/Decryption. [ 3.858928] systemd[1]: Journal Audit Socket was skipped because of an unmet condition check (ConditionSecurity=audit). [ 3.859523] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). [ OK ] Listening on [ 3.887537] systemd[1]: Listening on Journal Sockets. Journal Sockets. [ OK ] Listening on [ 3.904161] systemd[1]: Listening on Network Service Netlink Socket. Network Service Netlink Socket. [ OK ] Listening on [ 3.923928] systemd[1]: Listening on udev Control Socket. udev Control Socket. [ 3.943890] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. Mounting Huge P[ 3.968641] systemd[1]: Mounting Huge Pages File System... ages File System... Mounting POSIX [ 4.020322] systemd[1]: Mounting POSIX Message Queue File System... Message Queue File System... Mounting Kernel[ 4.042265] systemd[1]: Mounting Kernel Debug File System... Debug File System... [ 4.059480] systemd[1]: Kernel Trace File System was skipped because of an unmet condition check (ConditionPathExists=/sys/kernel/tracing). Mounting Tempor[ 4.072914] systemd[1]: Mounting Temporary Directory /tmp... ary Directory /tmp... [ 4.096301] systemd[1]: Starting Create List of Static Device Nodes... Starting Create List of Static Device Nodes... [ 4.123126] systemd[1]: Starting Load Kernel Module configfs... Starting Load Kernel Module configfs... Starting Load K[ 4.143650] systemd[1]: Starting Load Kernel Module drm... ernel Module drm... Starting Load K[ 4.168020] systemd[1]: Starting Load Kernel Module fuse... ernel Module fuse... [ 4.187188] systemd[1]: File System Check on Root Device was skipped because of an unmet condition check (ConditionPathIsReadWrite=!/). Starting Journa[ 4.204761] systemd[1]: Starting Journal Service... l Service... [ 4.221038] fuse: init (API version 7.44) [ 4.224458] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... [ 4.242639] systemd[1]: Starting Generate network units from Kernel command line... Starting Generate network units from Kernel command line... [ 4.269033] cryptodev: loading out-of-tree module taints kernel. [ 4.270930] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remoun[ 4.283083] sysctl table check failed: ioctl/(null) procname is null t Root and Kernel File Systems 4.283112] sysctl table check failed: ioctl/(null) No proc_handler m... [ 4.283120] cryptodev: driver 1.14 loaded. Starting Load u[ 4.312024] systemd[1]: Starting Load udev Rules from Credentials... dev Rules from Credentials...[ 4.322112] openvswitch: Open vSwitch switching datapath [ 4.322258] systemd-journald[117]: Collecting audit messages is disabled. [ 4.343442] systemd[1]: Starting Coldplug All udev Devices... Starting Coldplug All udev Devices... [ 4.363867] EXT4-fs (mmcblk1p2): re-mounted e308576d-719f-483d-b1d4-58f9ba6df8e3. [ 4.376699] systemd[1]: Mounted Huge Pages File System. [ OK ] Mounted Huge Pages File System. [ 4.391489] systemd[1]: Mounted POSIX Message Queue File System. [ OK ] Mounted POSIX Message Queue File System. [ 4.407709] systemd[1]: Started Journal Service. [ OK ] Started Journal Service. [ OK ] Mounted Kernel Debug File System. [ OK ] Mounted Temporary Directory /tmp. [ OK ] Finished Create List of Static Device Nodes. [ OK ] Finished Load Kernel Module configfs. [ OK ] Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module fuse. [ OK ] Finished Load Kernel Modules. [ OK ] Finished Generate network units from Kernel command line. [ OK ] Finished Remount Root and Kernel File Systems. [ OK ] Finished Load udev Rules from Credentials. [ OK ] Reached target Preparation for Network. Mounting FUSE Control File System... Mounting Kernel Configuration File System... Starting Flush Journal to Persistent Storage... Starting Apply Kernel Variables... Starting Create[ 4.686959] systemd-journald[117]: Received client request to flush runtime journal. Static Device Nodes in /dev gracefully... [ OK ] Mounted FUSE Control File System. [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Flush Journal to Persistent Storage. [ OK ] Finished Apply Kernel Variables. [ OK ] Finished Create Static Device Nodes in /dev gracefully. Starting Network Name Resolution... Starting Network Time Synchronization... Starting Create Static Device Nodes in /dev... [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Preparation for Local File Systems. Starting Rule-based Manager for Device Events and Files... [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Time Set. [ OK ] Started Network Name Resolution. [ OK ] Reached target Host and Network Name Lookups. [ OK ] Started Rule-based Manager for Device Events and Files. Starting Network Configuration... [ OK ] Listening on Load/Save RF Kil[ 5.335365] cfg80211: Loading compiled-in X.509 certificates for regulatory database l Switch Status /dev/rfkill Watch. [ 5.369909] Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 5.370663] Loaded X.509 cert 'wens: 61c038651aabdcf94bd0ac7ff06c7248db18c600' Mounting /var/volatile... [ OK ] Started Network Configuration. [ OK ] Reached target Network. Starting Enable Persistent Storage in systemd-networkd... Starting Wait for Network to be Configured... [ OK ] Mounted /var/volatile. [ OK ] Reached target Local File Systems. Starting Create System Files and Directories... [ OK ] Finished Coldplug All udev Devices. [ OK ] Finished Enable Persistent Storage in systemd-networkd. [ OK ] Finished Create System Files and Directories. [ 5.668429] fec 30be0000.ethernet end0: renamed from eth0 [ OK ] Found device /dev/ttymxc0. [ OK ] Found device /dev/bootdev. Mounting /boot... Starting RPC Bind... [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target Timer Units. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Listening on PC/SC Smart Card Daemon Activation Socket. [ OK ] Listening on OpenSSH Server Socket…temd-ssh-generator, AF_UNIX Local). Starting sshd.socket... [ OK ] Mounted /boot. [ OK ] Listening on sshd.socket. [ OK ] Reached target Socket Units. [ OK ] Reached target Basic System. Starting D-Bus System Message Bus... [ OK ] Started Linux Firmware Loader Daemon. Starting User Login Management... Starting Permit User Sessions... Starting OpenSSH Key Generation... [ OK ] Started RPC Bind. [ OK ] Started D-Bus System Message Bus. [ OK ] Finished Permit User Sessions. [ OK ] Started Getty on tty1. [ 6.419622] gpio-fan fan: supply fan not found, using dummy regulator [ 6.420408] gpio-fan fan: GPIO fan initialized [ OK ] Started Serial Getty on ttymxc0. [ 6.446040] cs_system_cfg: CoreSight Configuration manager initialised [ OK ] Reached target Login Prompts. [ 6.473885] imx-cpufreq-dt imx-cpufreq-dt: cpu speed grade 7 mkt segment 2 supported-hw 0x80 0x4 [ 6.516873] CAN device driver interface [ 6.517579] caam 30900000.crypto: device ID = 0x0a16040100000100 (Era 9) [ 6.517600] caam 30900000.crypto: job rings = 2, qi = 0 [ OK ] Finished OpenSSH Key Generation. [ OK ] Started User Login Management. [ OK ] Reached target Multi-User System. [ 6.608733] input: 30370000.snvs:snvs-powerkey as /devices/platform/soc@0/30000000.bus/30370000.snvs/30370000.snvs:snvs-powerkey/input/input0 [ 6.639466] snvs_rtc 30370000.snvs:snvs-rtc-lp: registered as rtc1 [ 6.672798] at24 0-0051: 4096 byte 24c32 EEPROM, writable, 32 bytes/write [ 6.691360] rtc-rv3028 0-0052: registered as rtc0 [ 6.692446] rtc-rv3028 0-0052: setting system clock to 2025-11-24T14:07:02 UTC (1763993222) [ 6.710922] at24 1-0051: 256 byte 24c02 EEPROM, writable, 16 bytes/write [ 6.728235] imx-sdma 30bd0000.dma-controller: loaded firmware 4.6 [ 6.728718] imx-dwmac 30bf0000.ethernet: IRQ eth_lpi not found [ 6.728732] imx-dwmac 30bf0000.ethernet: IRQ sfty not found [ 6.730740] imx-dwmac 30bf0000.ethernet: User ID: 0x10, Synopsys ID: 0x51 [ 6.730763] imx-dwmac 30bf0000.ethernet: DWMAC4/5 [ 6.730769] imx-dwmac 30bf0000.ethernet: DMA HW capability register supported [ 6.730774] imx-dwmac 30bf0000.ethernet: RX Checksum Offload Engine supported [ 6.730777] imx-dwmac 30bf0000.ethernet: TX Checksum insertion supported [ 6.730781] imx-dwmac 30bf0000.ethernet: Wake-Up On Lan supported [ 6.731010] imx-dwmac 30bf0000.ethernet: Enable RX Mitigation via HW Watchdog Timer [ 6.731019] imx-dwmac 30bf0000.ethernet: Enabled L3L4 Flow TC (entries=8) [ 6.731024] imx-dwmac 30bf0000.ethernet: Enabled RFS Flow TC (entries=10) [ 6.731038] imx-dwmac 30bf0000.ethernet: Enabling HW TC (entries=256, max_off=256) [ 6.731045] imx-dwmac 30bf0000.ethernet: Using 34/40 bits DMA host/device width [ 6.743598] imx-sdma 30e00000.dma-controller: loaded firmware 4.6 [ 6.781488] leds-pca953x 1-0062: setting platform data [ 6.816622] imx-sdma 30e10000.dma-controller: loaded firmware 4.6 [ 6.832522] etnaviv etnaviv: bound 38000000.gpu (ops gpu_ops [etnaviv]) [ 6.833918] mc: Linux media interface: v0.10 [ 6.834185] etnaviv etnaviv: bound 38008000.gpu (ops gpu_ops [etnaviv]) [ 6.837578] etnaviv etnaviv: bound 38500000.npu (ops gpu_ops [etnaviv]) [ 6.837951] etnaviv-gpu 38000000.gpu: model: GC7000, revision: 6204 [ 6.838519] etnaviv-gpu 38008000.gpu: model: GC520, revision: 5341 [ 6.839502] etnaviv-gpu 38500000.npu: model: GC8000, revision: 8002 [ 6.839522] etnaviv-gpu 38500000.npu: etnaviv has been instantiated on a NPU, for which the UAPI is still experimental [ 6.855679] [drm] Initialized etnaviv 1.4.0 for etnaviv on minor 0 [ 6.873236] [drm] Initialized imx-lcdif 1.0.0 for 32e90000.display-controller on minor 1 [ 6.910416] videodev: Linux video capture interface: v2.00 [ 6.914274] Console: switching to colour frame buffer device 160x50 [ 6.933088] imx-lcdif 32e90000.display-controller: [drm] fb0: imx-lcdifdrmfb frame buffer device [ 6.951352] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 6.951394] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 1 [ 6.951770] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220fe6d hci version 0x110 quirks 0x000080a001000010 [ 6.951817] xhci-hcd xhci-hcd.1.auto: irq 221, io mem 0x38100000 [ 6.951939] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 6.951950] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 2 [ 6.951963] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed [ 6.955076] hub 1-0:1.0: USB hub found [ 6.955135] hub 1-0:1.0: 1 port detected [ 6.955554] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 6.956171] hub 2-0:1.0: USB hub found [ 6.956199] hub 2-0:1.0: 1 port detected [ 6.959796] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 6.959821] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 3 [ 6.960170] xhci-hcd xhci-hcd.2.auto: hcc params 0x0220fe65 hci version 0x110 quirks 0x000080a001000010 [ 6.960218] xhci-hcd xhci-hcd.2.auto: irq 222, io mem 0x38200000 [ 6.960333] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 6.960343] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 4 [ 6.960355] xhci-hcd xhci-hcd.2.auto: Host supports USB 3.0 SuperSpeed [ 6.961598] hub 3-0:1.0: USB hub found [ 6.961625] hub 3-0:1.0: 1 port detected [ 6.961903] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 6.966573] hub 4-0:1.0: USB hub found [ 6.966618] hub 4-0:1.0: 1 port detected [ 6.976483] hantro-vpu 38300000.video-codec: registered nxp,imx8mm-vpu-g1-dec as /dev/video0 [ 6.977691] hantro-vpu 38310000.video-codec: registered nxp,imx8mq-vpu-g2-dec as /dev/video1 [ 7.159954] TI DP83867 30be0000.ethernet-1:00: attached PHY driver (mii_bus:phy_addr=30be0000.ethernet-1:00, irq=POLL) [ OK ] Created slice Slice /system/tee-supplicant. Starting TEE Supplicant on teepriv0... [ 7.206876] usb 3-1: new high-speed USB device number 2 using xhci-hcd [ OK ] Finished Wait for Network to be Configured. [ OK ] Started TEE Supplicant on teepriv0. [ 7.271447] caam algorithms registered in /proc/crypto [ 7.271652] caam 30900000.crypto: caam pkc algorithms registered in /proc/crypto [ 7.271664] caam 30900000.crypto: registering rng-caam [ 7.271685] caam 30900000.crypto: rng crypto API alg registered prng-caam [ 7.272935] caam_jr 30903000.jr: failed to flush job ring 1 [ 7.272950] caam_jr 30903000.jr: probe with driver caam_jr failed with error -5 [ OK ] Reached target Network is Online. [ 7.336777] tpm_tis_spi spi1.0: 2.0 TPM (device-id 0x1B, rev-id 22) Starting Notify[ 7.339514] tpm tpm0: A TPM error (256) occurred attempting the self test NFS peers of a restart... [ 7.339535] tpm tpm0: starting up the TPM manually [ 7.365508] stmmac: wakeup enable [ 7.387713] imx-dwmac 30bf0000.ethernet end1: renamed from eth0 [ OK ] Started Notify NFS peers of a restart. [ 7.408977] hub 3-1:1.0: USB hub found [ 7.409089] hub 3-1:1.0: 4 ports detected [ 7.430452] imx-dwmac 30bf0000.ethernet end1: Register MEM_TYPE_PAGE_POOL RxQ-0 [ 7.444155] imx-dwmac 30bf0000.ethernet end1: PHY [stmmac-1:01] driver [TI DP83867] (irq=POLL) [ 7.455778] imx-dwmac 30bf0000.ethernet end1: No Safety Features support found [ 7.455809] imx-dwmac 30bf0000.ethernet end1: IEEE 1588-2008 Advanced Timestamp supported [ 7.456052] imx-dwmac 30bf0000.ethernet end1: registered PTP clock [ 7.465095] imx-dwmac 30bf0000.ethernet end1: configuring for phy/rgmii-id link mode [ 7.465600] 8021q: adding VLAN 0 to HW filter on device end1 [ 7.472411] usb 4-1: new SuperSpeed USB device number 2 using xhci-hcd [ 7.520675] hub 4-1:1.0: USB hub found [ 7.520786] hub 4-1:1.0: 4 ports detected ____ _ _ __ __ _____ _____ ____ | _ \ | | | |\ \ / /|_ _|| ____| / ___| | |_) || |_| | \ V / | | | _| | | | __/ | _ | | | | | | |___ | |___ |_| |_| |_| |_| |_| |_____| \____| _ __ __ ____ _ ___ ____ _ _ __ __ / \ | \/ || _ \ | | |_ _|| _ \ | | | |\ \ / / / _ \ | |\/| || |_) || | | | | |_) || |_| | \ V / / ___ \ | | | || __/ | |___ | | | __/ | _ | | | /_/ \_\|_| |_||_| |_____||___||_| |_| |_| |_| ampliPHY (Phytec Base Distribution) BSP-Yocto-Ampliphy-i.MX8MP-master-devel phyboard-pollux-imx8mp-3 ttymxc0 Type 'root' to login with superuser privileges (no password will be asked).phyboard-pollux-imx8mp-3 phyboard-pollux-imx8mp-3 login: [ 11.240565] fec 30be0000.ethernet end0: Link is Up - 1Gbps/Full - flow control rx/tx phyboard-pollux-imx8mp-3 login: root root@phyboard-pollux-imx8mp-3:~# lsmod Module Size Used by tpm_tis_spi 16384 0 tpm_tis_core 24576 1 tpm_tis_spi caam_jr 163840 0 caamhash_desc 12288 1 caam_jr caamalg_desc 32768 1 caam_jr authenc 12288 1 caam_jr libdes 20480 1 caam_jr hantro_vpu 282624 0 v4l2_vp9 20480 1 hantro_vpu v4l2_h264 12288 1 hantro_vpu v4l2_jpeg 16384 1 hantro_vpu v4l2_mem2mem 36864 1 hantro_vpu videobuf2_dma_contig 16384 1 hantro_vpu videobuf2_memops 12288 1 videobuf2_dma_contig videobuf2_v4l2 28672 2 hantro_vpu,v4l2_mem2mem videodev 253952 3 videobuf2_v4l2,hantro_vpu,v4l2_mem2mem fsl_imx8_ddr_perf 20480 0 videobuf2_common 57344 5 videobuf2_dma_contig,videobuf2_v4l2,hantro_vpu,v4l2_mem2mem,videobuf2_memops fsl_ldb 12288 0 mc 57344 5 videodev,videobuf2_v4l2,hantro_vpu,videobuf2_common,v4l2_mem2mem etnaviv 94208 0 phy_fsl_imx8mq_usb 12288 4 imx_lcdif 16384 0 gpu_sched 40960 1 etnaviv drm_dma_helper 20480 2 imx_lcdif dwmac_imx 12288 0 stmmac_platform 16384 1 dwmac_imx leds_pca9532 12288 0 stmmac 241664 3 stmmac_platform,dwmac_imx imx_sdma 28672 2 at24 24576 0 pcs_xpcs 32768 1 stmmac rtc_rv3028 16384 0 rtc_snvs 12288 1 imx8mm_thermal 12288 0 snvs_pwrkey 12288 0 pwm_imx27 12288 1 flexcan 28672 0 spi_imx 24576 0 coresight_tmc 49152 0 caam 32768 1 caam_jr can_dev 40960 1 flexcan error 20480 4 caamalg_desc,caamhash_desc,caam,caam_jr panel_simple 98304 0 imx_cpufreq_dt 12288 0 coresight_funnel 12288 0 coresight 77824 2 coresight_tmc,coresight_funnel pwm_bl 12288 0 gpio_fan 16384 0 backlight 20480 1 pwm_bl sha256 16384 0 libsha256_generic 12288 1 sha256 cfg80211 430080 0 rfkill 28672 2 cfg80211 openvswitch 147456 0 nsh 12288 1 openvswitch nf_conncount 24576 1 openvswitch nf_nat 49152 1 openvswitch cryptodev 49152 0 fuse 159744 1 nfnetlink 20480 2 ipv6 475136 30 root@phyboard-pollux-imx8mp-3:~# cat /proc/version Linux version 6.16.11-yocto-standard-g42ddd61a7bce (oe-user@oe-host) (aarch64-phytec-linux-gcc (GCC) 15.2.0, GNU ld (GNU Binutils) 2.45.0.20250908) #1 SMP PREEMPT Mon Oct 6 13:50:41 UTC 2025 root@phyboard-pollux-imx8mp-3:~# zcat /proc/config.gz | grep PREEMPT CONFIG_PREEMPT_BUILD=y CONFIG_ARCH_HAS_PREEMPT_LAZY=y # CONFIG_PREEMPT_NONE is not set # CONFIG_PREEMPT_VOLUNTARY is not set CONFIG_PREEMPT=y # CONFIG_PREEMPT_LAZY is not set CONFIG_PREEMPT_COUNT=y CONFIG_PREEMPTION=y # CONFIG_PREEMPT_DYNAMIC is not set CONFIG_PREEMPT_RCU=y CONFIG_HAVE_PREEMPT_DYNAMIC=y CONFIG_HAVE_PREEMPT_DYNAMIC_KEY=y CONFIG_PREEMPT_NOTIFIERS=y # CONFIG_DEBUG_PREEMPT is not set root@phyboard-pollux-imx8mp-3:~#