=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2016.01.16 20:59:48 =~=~=~=~=~=~=~=~=~=~=~=
[ 20.283942@2] hdmitx: cec: CEC node init
[ 20.284209@2] hdmitx: cec: cec_func_config: 0xb; P_AO_DEBUG_REG0:0xb
[ 20.288656@2] hdmitx: cec: enable:int mask:0x6
[ 20.293832@2] hdmitx: cec: CEC: start poll dev
[ 20.297814@2] hdmitx: cec: CEC_LOGICAL_ADDR0:0x1f
[ 20.302480@2] hdmitx: cec: now tx_stat:0
[ 20.306355@2] hdmitx: cec: start poll
[ 20.484562@2] hdmitx: cec: end poll, tx_stat:3
[ 20.484834@2] CEC: tx msg len: 1 dat: 44
[ 20.487595@2] hdmitx: cec: CEC: poll online logic device: 0x4 BOOL: 0
[ 20.494077@2] hdmitx: cec: player_dev[0]:0x4
[ 20.498248@2] hdmitx: cec: physical address:0x2000
[ 20.503022@2] hdmitx: cec: Set logical address: 4
[ 20.615339@2] CEC: tx msg len: 5 dat: 4f 84 20 00 04
[ 20.741484@0] hdmitx: cec: aocec irq 2
[ 20.775369@2] CEC: tx msg len: 5 dat: 4f 87 00 00 00
[ 20.901514@0] hdmitx: cec: aocec irq 2
[ 20.934967@2] CEC: tx msg len: 2 dat: 40 04
*** Error in mount_flash: mount_common: Could not mount /dev/system ***
### Starting debugging shell... type exit to quit ###
[ 21.073371@0] hdmitx: cec: aocec irq 2
[ 21.073917@0] hdmitx: cec: TX ERROR!!!
[ 21.085649@2] CEC: tx msg len: 2 dat: 40 91
[ 21.227418@0] hdmitx: cec: aocec irq 2
[ 21.227971@0] hdmitx: cec: TX ERROR!!!
[ 21.445274@2] CEC: tx msg len: 4 dat: 4f 82 20 00
[ 21.547185@0] hdmitx: cec: aocec irq 2
[ 21.575094@2] CEC: tx msg len: 3 dat: 40 8e 00
[ 21.683925@2] hdmitx: cec: cec node init: cec features ok !
[ 21.713477@0] hdmitx: cec: aocec irq 2
[ 21.714033@0] hdmitx: cec: TX ERROR!!!
†!UÒššŠºšj
BT : 12:14:11 Jan 11 2016
PMU:rn5t618
DC01 v:1100, 0x[36]: 18 -> 28
DC02 v:1150, 0x[37]: 18 -> 2c
DC03 v:1500, 0x[38]: 38 -> 48
LDO01 v:2900, 0x[4c]: 4e -> 50
LDO02 v:1800, 0x[4d]: 24 -> 24
LDO03 v:1800, 0x[4e]: 30 -> 30
LDO04 v:2850, 0x[4f]: 4e -> 4e
LDO05 v:1800, 0x[50]: 24 -> 24
LDO0a v:2700, 0x[56]: 28 -> 28
LDO0b v:900, 0x[57]: 00 -> 00
CPU clock is 1200MHz
CPU type: M8
DDR info: 2GB(auto) @ 792MHz(1T)
DDR channel: DDR 0 + DDR 1
DDR init use : 12111 us
HHH
Boot From SPI
ucl decompress...pass
0x12345678
Boot from internal device 1st SPI
TE : 407116
System Started
U-boot-00000-g99c5e8c-dirty(m8_k200_v1@m201) (Jan 11 2016 - 12:14:01)
clr h-ram
DRAM: 2 GiB
relocation Offset is: 6feb0000
show partition table:
part: 0, name : logo, size : 2000000
part: 1, name : recovery, size : 2000000
part: 2, name : misc, size : 2000000
part: 3, name : boot, size : 2000000
part: 4, name : system, size : 40000000
part: 5, name : cache, size : 20000000
part: 6, name : data, size : end
aml_card_type=0x200
MMC: [mmc_register] add mmc dev_num=0, port=1, if_type=6
[mmc_register] add mmc dev_num=1, port=2, if_type=6
SDIO Port B: 0, SDIO Port C: 1
PMU fault status:
reg[0x9A] = 0x1d
LSI version:03, OTP version:06
PMU type:RN5T618
register usb cfg[0][1] = 7ff68328
register usb cfg[2][0] = 7ff6be54
mcli -- wifi_power_init in uboot --
enter spi boot
SF: Detected MX25L1605D with page size 256, total 2 MiB
SPI NOR Flash have write protect!!!
spi success
get_storage_device_flag: store 4
boot_device_flag 0
Nand PHY driver Version: 2.01.001.0004 (c) 2013 Amlogic Inc.
amlnf_phy_init : amlnf init flag 5
NAND device id: 2c 64 44 4b a9 0 0 0
detect NAND device: B revision NAND 8GiB MT29F64G08CBABA
nand chip ce mask 1
device_boot_flag=4
boot_device_flag 0
Nand PHY driver Version: 2.01.001.0004 (c) 2013 Amlogic Inc.
amlnf_phy_init : amlnf init flag 0
NAND device id: 2c 64 44 4b a9 0 0 0
detect NAND device: B revision NAND 8GiB MT29F64G08CBABA
nand chip ce mask 1
AML_NAND_NEW_OOB : new oob
bus_cycle=6, bus_timing=8,system=3.9ns,flash->T_REA =16,flash->T_RHOH=15
NAND CKECK : arg nbbt: arg_valid= 1, valid_blk_addr = 9, valid_page_addr = 0
nand block at blk 4 is bad
nand block at blk 5 is bad
nand block at blk 6 is bad
nand block at blk 7 is bad
NAND CKECK : arg ncnf: arg_valid= 1, valid_blk_addr = 10, valid_page_addr = 0
nand block at blk 4 is bad
nand block at blk 5 is bad
nand block at blk 6 is bad
nand block at blk 7 is bad
NAND CKECK : arg nkey: arg_valid= 1, valid_blk_addr = 8, valid_page_addr = 43
i=0,register --- nand_key
nand block at blk 4 is bad
nand block at blk 5 is bad
nand block at blk 6 is bad
nand block at blk 7 is bad
NAND CKECK : arg phyp: arg_valid= 1, valid_blk_addr = 11, valid_page_addr = 1
nand blk 4 is shipped bad block
nand blk 5 is shipped bad block
nand blk 6 is shipped bad block
nand blk 7 is shipped bad block
amlnand_phydev_init,1171,phydev->offset=6800000,phydev->size=24800000
amlnand_phydev_init,1171,phydev->offset=2b000000,phydev->size=51800000
amlnand_phydev_init,1171,phydev->offset=7c800000,phydev->size=183800000
nfcache : offset: 0x000006800000 -0x000024800000 : partitons 1 : single_chip multi_plane
nfcode : offset: 0x00002b000000 -0x000051800000 : partitons 5 : single_chip multi_plane
nfdata : offset: 0x00007c800000 -0x000183800000 : partitons 1 : single_chip multi_plane
amlnf_logic_init: START
amlnf_logic_init: COMPLETE
SPI BOOT,spi_env_relocate_spec : env_relocate_spec 64
spi env have been init already, just retun here
set_storage_device_flag: store 4
Multi dtb tool version: v2 .
Multi dtb detected, support 6 dtbs.
aml_dt soc: m8 platform: k200 variant: 2gsdhc
dtb 0 soc: m8 plat: k200 vari: 2gsdhc
dtb 1 soc: m8 plat: k200 vari: 2gsdio
dtb 2 soc: m8 plat: k200 vari: sdhc
dtb 3 soc: m8 plat: k200 vari: sdio
dtb 4 soc: m8m2 plat: n200 vari: 1G
dtb 5 soc: m8m2 plat: n200 vari: 2G
Find match dtb: 0
vpu driver detect cpu type: m8
vpu clk_level in dts: 7
set vpu clk: 364300000Hz, readback: 364300000Hz(0x700)
Net: Meson_Ethernet
init suspend firmware done. (ret:0)
cvbs trimming.1.v5: 0xa0, 0x0
charging
bootmode= misc
wipe_data=successful
wipe_cache=successful
reboot_mode=charging
TV mode 1080p selected.
mode = 8 vic = 16
set HDMI vic: 16
config HPLL
config HPLL done
reconfig packet setting done
update by key...
Enter USB burn
Try connect time out 1001, 1000, 1835
sdio_detect return 1
sdio debug board detected, no sd card in
enter recovery
sdio_detect return 1
sdio debug board detected, no sd card in
(Re)start USB(0)...
USB0: dwc_usb driver version: 2.94 6-June-2012
USB (1) peri reg base: c1108820
USB (1) use clock source: XTAL input
USB (1) base addr: 0xc90c0000
Force id mode: Host
dwc_otg: Highspeed device found !
scanning bus 0 for devices... 2 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
** Invalid boot device **
## ANDROID Format IMAGE
## Booting kernel from Legacy Image at 12000000 ...
Image Name: Linux-3.10.33
Image Type: ARM Linux Kernel Image (lzo compressed)
Data Size: 6708859 Bytes = 6.4 MiB
Load Address: 00208000
Entry Point: 00208000
Verifying Checksum ... OK
Ramdisk start addr = 0x12666800, len = 0x29b47e
Multi dtb tool version: v2 .
Multi dtb detected, support 6 dtbs.
aml_dt soc: m8 platform: k200 variant: 2gsdhc
dtb 0 soc: m8 plat: k200 vari: 2gsdhc
dtb 1 soc: m8 plat: k200 vari: 2gsdio
dtb 2 soc: m8 plat: k200 vari: sdhc
dtb 3 soc: m8 plat: k200 vari: sdio
dtb 4 soc: m8m2 plat: n200 vari: 1G
dtb 5 soc: m8m2 plat: n200 vari: 2G
Find match dtb: 0
Flat device tree start addr = 0x12902800, len = 0x516a magic=0xedfe0dd0
board_usb_stop cfg: 0
Uncompressing Kernel Image ... OK
uboot time: 13764828 us.
EFUSE machid is not set.
Using machid 0xf81 from environment
From device tree /memory/ node aml_reserved_end property, for relocate ramdisk and fdt, relocate_addr: 0x52a5001
Loading Ramdisk to 05009000, end 052a447e ... OK
Loading Device Tree to 05000000, end 05008169 ... OK
Starting kernel ...
[ 0.000000@0] Booting Linux on physical CPU 0x200
[ 0.000000@0] Initializing cgroup subsys cpu
[ 0.000000@0] Initializing cgroup subsys cpuacct
[ 0.000000@0] Linux version 3.10.33-gfa4a182-dirty (user@DroidBOX) (gcc version 4.8.2 (Ubuntu/Linaro 4.8.2-16ubuntu4) ) #2 SMP PREEMPT Fri Jan 15 09:37:53 CET 2016
[ 0.000000@0] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c5387d
[ 0.000000@0] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000@0] Machine: Amlogic Meson8, model: AMLOGIC
[ 0.000000@0] physical memory start address is 0x200000
[ 0.000000@0] reserved_end is 1d9fffff
[ 0.000000@0]
[ 0.000000@0] Total memory is 2046 MiB
[ 0.000000@0] Reserved low memory from 0x06000000 to 0x1d9fffff, size: 378 MiB
[ 0.000000@0] mesonfb0(low) : 0x06100000 - 0x07900000 ( 24 MiB)
[ 0.000000@0] mesonfb1(low) : 0x07900000 - 0x07a00000 ( 1 MiB)
[ 0.000000@0] deinterlace0(high) : 0x7df00000 - 0x80000000 ( 33 MiB)
[ 0.000000@0] mesonstream0(low) : 0x07a00000 - 0x09a00000 ( 32 MiB)
[ 0.000000@0] vdec0(low) : 0x09a00000 - 0x19a00000 (256 MiB)
[ 0.000000@0] ppmgr0(high) : 0x7bf00000 - 0x7df00000 ( 32 MiB)
[ 0.000000@0] vdin00(low) : 0x19a00000 - 0x1aa00000 ( 16 MiB)
[ 0.000000@0] vdin10(low) : 0x1aa00000 - 0x1ba00000 ( 16 MiB)
[ 0.000000@0] amlvideo20(low) : 0x1ba00000 - 0x1d200000 ( 24 MiB)
[ 0.000000@0] amvideocap0(low) : 0x1d200000 - 0x1da00000 ( 8 MiB)
[ 0.000000@0] get storage device: storage 4
[ 0.000000@0] value=4
[ 0.000000@0] get_storage_device : get storage device: storage 4
[ 0.000000@0] get_storage_device : value=4
[ 0.000000@0] [get_storage_device] storage_flag=4
[ 0.000000@0] [get_storage_device] the storage device does NOT relate to eMMC, storage_flag=4
[ 0.000000@0] cma: CMA: reserved 8 MiB at 2f000000
[ 0.000000@0] cma: Found region@0, memory base 0, size 18 MiB
[ 0.000000@0] cma: CMA: reserved 20 MiB at 2dc00000
[ 0.000000@0] Memory policy: ECC disabled, Data cache writealloc
[ 0.000000@0] Meson chip version = RevC (19:C - 0:27ED)
[ 0.000000@0] PERCPU: Embedded 9 pages/cpu @c1f09000 s13120 r8192 d15552 u36864
[ 0.000000@0] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 405264
[ 0.000000@0] Kernel command line: rootfstype=ramfs init=/init console=ttyS0,115200n8 no_console_suspend earlyprintk ramoops.mem_address=0x04e00000 ramoops.mem_size=0x100000 ramoops.record_size=0x8000 ramoops.console_size=0x4000 androidboot.selinux=permissive storage=4 cvbsdrv=0 vdaccfg=0xa000 logo=osd1,loaded,0x07900000,1080p,full hdmimode=1080p cvbsmode=576cvbs androidboot.firstboot=1 hdmitx= wipeinstaboot
[ 0.000000@0] cvbs performance line = 0
[ 0.000000@0] cvbs trimming line = 0xa000
[ 0.000000@0] cvbs trimming.1.v5: 0xa0, 0x0
[ 0.000000@0] osd1:1
[ 0.000000@0] loaded:268435459
[ 0.000000@0] logo has been loaded
[ 0.000000@0] 1080p:15
[ 0.000000@0] full:2
[ 0.000000@0] kernel get hdmimode form uboot is 1080p
[ 0.000000@0] kernel get cvbsmode form uboot is 576cvbs
[ 0.000000@0] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000@0] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000@0] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000@0] Memory: 64MB 16MB 1509MB = 1589MB total
[ 0.000000@0] Memory: 1563352k/1563352k available, 63784k reserved, 1250304K highmem
[ 0.000000@0] Virtual kernel memory layout:
[ 0.000000@0] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000@0] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000@0] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB)
[ 0.000000@0] lowmem : 0xc0000000 - 0xef800000 ( 760 MB)
[ 0.000000@0] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000@0] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000@0] .text : 0xc0008000 - 0xc0b83bc0 (11759 kB)
[ 0.000000@0] .init : 0xc0b84000 - 0xc0be3340 ( 381 kB)
[ 0.000000@0] .data : 0xc0be4000 - 0xc0c9d0e8 ( 741 kB)
[ 0.000000@0] .bss : 0xc0c9d0e8 - 0xc0f75f94 (2916 kB)
[ 0.000000@0] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000@0] Preemptible hierarchical RCU implementation.
[ 0.000000@0] NR_IRQS:256
[ 0.000000@0] sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 4294967ms
[ 0.000000@0] Switching to timer-based delay loop
[ 0.000000@0] console [ttyS0] enabled
[ 0.397370@0] Calibrating delay loop (skipped), value calculated using timer frequency.. 2.00 BogoMIPS (lpj=10000)
[ 0.407669@0] pid_max: default: 32768 minimum: 301
[ 0.412566@0] Security Framework initialized
[ 0.416688@0] SELinux: Disabled at boot.
[ 0.420761@0] Mount-cache hash table entries: 512
[ 0.428589@0] Initializing cgroup subsys debug
[ 0.429776@0] Initializing cgroup subsys freezer
[ 0.434442@0] CPU: Testing write buffer coherency: ok
[ 0.439686@0] CPU0: thread -1, cpu 0, socket 2, mpidr 80000200
[ 0.445267@0] Setting up static identity map for 0xc07f1970 - 0xc07f19c8
[ 0.451989@0] L310 cache controller enabled
[ 0.456037@0] l2x0: 8 ways, 4096 sets, CACHE_ID 0x4100a0c9, Cache size: 1048576 B
[ 0.463612@0] AUX_CTRL 0x7ec80001, PERFETCH_CTRL 0x71000007, POWER_CTRL 0x00000000
[ 0.471730@0] TAG_LATENCY 0x00000111, DATA_LATENCY 0x00000222
[ 0.550144@0] write pen_release: 1
[ 0.550320@1] CPU1: Booted secondary processor
[ 0.550333@1] CPU1: thread -1, cpu 1, socket 2, mpidr 80000201
[ 0.570147@0] write pen_release: 2
[ 0.578289@2] CPU2: Booted secondary processor
[ 0.578300@2] CPU2: thread -1, cpu 2, socket 2, mpidr 80000202
[ 0.590139@0] write pen_release: 3
[ 0.598279@3] CPU3: Booted secondary processor
[ 0.598291@3] CPU3: thread -1, cpu 3, socket 2, mpidr 80000203
[ 0.598358@0] Brought up 4 CPUs
[ 0.611491@0] SMP: Total of 4 processors activated (8.00 BogoMIPS).
[ 0.617720@0] CPU: All CPU(s) started in SVC mode.
[ 0.622976@0] devtmpfs: initialized
[ 0.630585@0] clkrate [ xtal ] : 24000000
[ 0.630614@0] clkrate [ pll_sys ] : 1200000000
[ 0.634537@0] clkrate [ pll_fixed ] : 2550000000
[ 0.639217@0] clkrate [ pll_vid ] : 366000000
[ 0.643645@0] TODO: clk_get_rate_hpll() is not implement in M8 now
[ 0.649792@0] clkrate [ pll_hpll ] : 0
[ 0.653612@0] clkrate [ pll_ddr ] : 0
[ 0.657335@0] clkrate [ a9_clk ] : 1200000000
[ 0.661761@0] clkrate [ clk81 ] : 141666666
[ 0.666727@0] pinctrl core: initialized pinctrl subsystem
[ 0.671551@0] regulator-dummy: no parameters
[ 0.676472@0] NET: Registered protocol family 16
[ 0.686082@0] DMA: preallocated 4096 KiB pool for atomic coherent allocations
[ 0.687668@0] ramoops: using module parameters
[ 0.692166@0] pstore przs=0xf0010000
[ 0.695554@0] pstore cprz=0xf0008000
[ 0.699464@0] console [pstore-1] enabled
[ 0.703016@0] ram_console: failed to create proc entry
[ 0.709017@0] VPU driver version: v03
[ 0.711772@0] vpu driver detect cpu type: m8
[ 0.716010@0] load vpu_clk in dts: 364300000Hz(7)
[ 0.720707@0] vpu_probe OK
[ 0.723615@0] cma: Assigned CMA region with name cma_0 to amvenc_avc.0 device
[ 0.732387@0] amlogic_gpio gpio: Probed amlogic GPIO driver
[ 0.736171@0] register lm device lm-root
[ 0.739968@0] register lm device lm1
[ 0.743528@0] register lm device lm0
[ 0.747161@0] Init pinux probe!
[ 0.750552@0] pinmux-m8 pinmux: Probed amlogic pinctrl driver
[ 0.755899@0] tv_init_module
[ 0.758748@0] major number 254 for disp
[ 0.762567@0] vout_register_server
[ 0.765938@0] register tv module server ok
[ 0.770037@0] major number 0 for disp
[ 0.773653@0] register tv module server ok
[ 0.777738@0] video2_early_init enter
[ 0.781374@0] video2_early_init exit
[ 0.784945@0] aml_i2c version: 20140813
[ 0.788861@0] aml-i2c i2c-AO: add adapter aml_i2c_adap0(ed73d0a8)
[ 0.794815@0] aml-i2c i2c-AO: aml i2c bus driver.
[ 0.799577@0] aml-i2c i2c-A: add adapter aml_i2c_adap1(ed73d4a8)
[ 0.805476@0] aml-i2c i2c-A: aml i2c bus driver.
[ 0.810175@0] aml-i2c i2c-B: add adapter aml_i2c_adap2(ed73d8a8)
[ 0.816043@0] aml-i2c i2c-B: aml i2c bus driver.
[ 0.820733@0] aml-i2c i2c-C: add adapter aml_i2c_adap3(ed73dca8)
[ 0.826618@0] aml-i2c i2c-C: aml i2c bus driver.
[ 0.831273@0] aml_pmu_init, 458
[ 0.834347@0] call aml_dvfs_init in
[ 0.837960@0] hdmitx: system: amhdmitx_init
[ 0.841967@0] hdmitx: system: Ver: 2014May6
[ 0.846174@0] hdmitx: system: amhdmitx_probe
[ 0.850509@0] hdmitx: system: not find cec config
[ 0.855047@0] hdmitx: system: not find vend_init_data
[ 0.860173@0] hdmitx: system: gate/pwr cmd: 7
[ 0.864411@0] hdmitx: system: ALREADY init VIC = 16
[ 0.869263@0] hdmitx: system: gate/pwr cmd: 0
[ 0.873993@1] hdmitx: system: reset intr mask
[ 0.890357@0] hdmitx: system: irq 1
[ 0.904234@0] bio: create slab <bio-0> at 0
[ 0.904639@0] SCSI subsystem initialized
[ 0.906790@0] usbcore: registered new interface driver usbfs
[ 0.912355@0] usbcore: registered new interface driver hub
[ 0.917826@0] usbcore: registered new device driver usb
[ 0.923057@0] Linux video capture interface: v2.00
[ 0.927768@0] pps_core: LinuxPPS API ver. 1 registered
[ 0.932865@0] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <[email protected]>
[ 0.942146@0] PTP clock support registered
[ 0.946445@0] mode is 15,sync_duration_den=1,sync_duration_num=60
[ 0.952287@0] TV mode 1080p selected.
[ 0.955915@0] already display in uboot
[ 0.959642@0] vinfo mode is: 1080p
[ 0.965034@0] call aml_pmu_probe_init in
[ 0.966971@0] aml_pmus_probe, child name:rn5t618
[ 0.971530@0] aml_pmus_probe, i2c_bus:i2c_bus_ao
[ 0.976383@0] board_has_battery:false
[ 0.980219@0] Allocate new i2c device: adapter:0, addr:0x32, node name:rn5t618, type:ricoh_pmu
[ 0.988531@0] Advanced Linux Sound Architecture Driver Initialized.
[ 0.994866@0] Bluetooth: Core ver 2.16
[ 0.998330@0] NET: Registered protocol family 31
[ 1.002907@0] Bluetooth: HCI device and connection manager initialized
[ 1.009403@0] Bluetooth: HCI socket layer initialized
[ 1.010723@1] hdmitx: system: gate/pwr cmd: 4
[ 1.018773@0] Bluetooth: L2CAP socket layer initialized
[ 1.023977@0] Bluetooth: SCO socket layer initialized
[ 1.029132@0] cfg80211: Calling CRDA to update world regulatory domain
[ 1.036609@0] Switching to clocksource Timer-E
[ 1.051631@0] NET: Registered protocol family 2
[ 1.052009@0] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[ 1.057764@0] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 1.064381@0] TCP: Hash tables configured (established 4096 bind 4096)
[ 1.070854@0] TCP: reno registered
[ 1.074195@0] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 1.080196@0] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 1.086739@0] NET: Registered protocol family 1
[ 1.091188@0] wifi_dev_probe
[ 1.093957@0] wifi_dt : interrupt_pin=GPIOX_21
[ 1.098383@0] wifi_dt : irq_num=null
[ 1.101941@0] wifi_dt : irq_trigger_type=GPIO_IRQ_HIGH
[ 1.107044@0] wifi_dt : power_on_pin=GPIOAO_6
[ 1.111392@0] wifi_dt : power_on_pin2=GPIOX_11
[ 1.115805@0] interrupt_pin=133, irq_num=4, irq_trigger_type=0, power_on_pin=6,clock_32k_pin=122
[ 1.124748@0] Unpacking initramfs...
[ 1.220234@1] hdmitx: system: gate/pwr cmd: 5
[ 1.220276@1] hdmitx: edid: edid ready
[ 1.221403@0] Freeing initrd memory: 2668K (c4e09000 - c50a4000)
[ 1.222579@0] audit: initializing netlink socket (disabled)
[ 1.222604@0] type=2000 audit(1.110:1): initialized
[ 1.223095@0] bounce pool size: 64 pages
[ 1.225995@0] VFS: Disk quotas dquot_6.5.2
[ 1.226146@0] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.227320@0] exFAT: Core Version 1.2.4
[ 1.227323@0] exFAT: FS Version 1.2.4
[ 1.228005@0] NTFS driver 2.1.30 [Flags: R/O].
[ 1.228178@0] fuse init (API version 7.22)
[ 1.269694@1] hdmitx: system: gate/pwr cmd: 4
[ 1.269875@0] msgmni has been set to 672
[ 1.270626@0] NET: Registered protocol family 38
[ 1.270735@0] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
[ 1.270738@0] io scheduler noop registered
[ 1.270741@0] io scheduler deadline registered
[ 1.270823@0] io scheduler cfq registered (default)
[ 1.273239@0] loop: module loaded
[ 1.273606@0] tun: Universal TUN/TAP device driver, 1.6
[ 1.273608@0] tun: (C) 1999-2004 Max Krasnyansky <[email protected]>
[ 1.273707@0] PPP generic driver version 2.4.2
[ 1.273792@0] PPP BSD Compression module registered
[ 1.273794@0] PPP Deflate Compression module registered
[ 1.273802@0] PPP MPPE Compression module registered
[ 1.273805@0] NET: Registered protocol family 24
[ 1.273859@0] usbcore: registered new interface driver asix
[ 1.273924@0] usbcore: registered new interface driver ax88179_178a
[ 1.273953@0] usbcore: registered new interface driver cdc_ether
[ 1.273980@0] usbcore: registered new interface driver dm9601
[ 1.274003@0] usbcore: registered new interface driver net1080
[ 1.274026@0] usbcore: registered new interface driver cdc_subset
[ 1.274048@0] usbcore: registered new interface driver zaurus
[ 1.274093@0] usbcore: registered new interface driver cdc_ncm
[ 1.274115@0] usbcore: registered new interface driver qf9700
[ 1.274143@0] usbcore: registered new interface driver sr9600
[ 1.274293@0] usbcore: registered new interface driver cdc_acm
[ 1.274295@0] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 1.274327@0] usbcore: registered new interface driver usb-storage
[ 1.274398@0] usbcore: registered new interface driver usbserial
[ 1.274420@0] usbcore: registered new interface driver option
[ 1.274438@0] usbserial: USB Serial support registered for GSM modem (1-port)
[ 1.274597@0] mousedev: PS/2 mouse device common for all mice
[ 1.274787@0] usbcore: registered new interface driver xpad
[ 1.274814@0] usbcore: registered new interface driver usb_acecad
[ 1.274839@0] usbcore: registered new interface driver aiptek
[ 1.274862@0] usbcore: registered new interface driver gtco
[ 1.274892@0] usbcore: registered new interface driver hanwang
[ 1.274924@0] usbcore: registered new interface driver kbtab
[ 1.274946@0] usbcore: registered new interface driver wacom
[ 1.275005@0] i2c /dev entries driver
[ 1.275319@0] usbcore: registered new interface driver uvcvideo
[ 1.275320@0] USB Video Class driver (1.1.1)
[ 1.275485@0] device-mapper: uevent: version 1.0.3
[ 1.275643@0] device-mapper: ioctl: 4.24.0-ioctl (2013-01-15) initialised: [email protected]
[ 1.275779@0] Bluetooth: HCI UART driver ver 2.2
[ 1.275783@0] Bluetooth: HCI H4 protocol initialized
[ 1.275968@0] hidraw: raw HID events driver (C) Jiri Kosina
[ 1.277335@0] usbcore: registered new interface driver usbhid
[ 1.277337@0] usbhid: USB HID core driver
[ 1.277637@0] zram: Created 1 device(s) ...
[ 1.277896@0] ashmem: initialized
[ 1.277998@0] logger: created 256K log 'log_main'
[ 1.278095@0] logger: created 256K log 'log_events'
[ 1.278191@0] logger: created 256K log 'log_radio'
[ 1.278283@0] logger: created 256K log 'log_system'
[ 1.278412@0] vout_init_module
[ 1.278456@0] start init vout module
[ 1.278479@0] create vout attribute ok
[ 1.278805@0] ge2d_init
[ 1.278809@0] ge2d_dev major:243
[ 1.278914@0] ge2d start monitor
[ 1.278951@0] osd_init
[ 1.278955@2] ge2d workqueue monitor start
[ 1.278980@0] osd_probe, vinfo:c084ccc0
[ 1.279157@0] Frame buffer memory assigned at phy:0x06100000, vir:0xf1000000, size=24576K
[ 1.279159@0] osd_probe, mydef_var:c0c36bf0, vinfo:c084ccc0
[ 1.279162@0] init fbdev bpp is :32
[ 1.279164@0] ---------------clear framebuffer0 memory
[ 1.628960@0] Frame buffer memory assigned at phy:0x07900000, vir:0xf0400000, size=1024K
[ 1.631421@0] osd_probe, mydef_var:c0c36bf0, vinfo:c084ccc0
[ 1.636952@0] don't find to display_size_default from mesonfb-dts
[ 1.643028@0] init fbdev bpp is :16
[ 1.662212@0] osd probe ok
[ 1.662312@0] osd_ext_init
[ 1.662528@0] vout2_init_module enter
[ 1.665637@0] start init vout2 module
[ 1.669272@0] create vout2 attribute ok
[ 1.673213@0] enter aml_sysled_init
[ 1.676983@0] amlvideo-000: V4L2 device registered as video10
[ 1.682499@0] amlvideo2: V4L2 device registered as video11
[ 1.687956@0] ionvideo-000: V4L2 device registered as video13
[ 1.693534@0] Video Technology Magazine Ion Video Capture Board ver 1.0 successfully loaded.
[ 1.702206@0] aml_wdt_driver_init,301
[ 1.705570@0] ** disable watchdog
[ 1.708987@0] keys===========================================
[ 1.714625@0] keys_devno=f000000
[ 1.717869@0] securitykey: device aml_keys created
[ 1.722591@0] amlkeys=0
[ 1.725009@0] platform_driver_register--aml_keys_driver--------------------
[ 1.732144@0] set uart_ao pinmux use pinctrl subsystem
[ 1.737036@0] P_AO_RTI_PIN_MUX_REG:5860
[ 1.740900@0] start uart_ao_ttyS0:(irq = 122)
[ 1.745184@0] register uart_ao ok
[ 1.748625@0] set uart_a pinmux use pinctrl subsystem
[ 1.753533@0] P_AO_RTI_PIN_MUX_REG:5860
[ 1.757330@0] start uart_a_ttyS1:(irq = 58)
[ 1.761503@0] register uart_a ok
[ 1.764823@0] start uart_d_ttyS4:(irq = 126)
[ 1.768935@0] register uart_d ok
[ 1.772246@0] dwc_otg: version 3.10a 12-MAY-2014
[ 1.776760@0] dwc_otg_driver_probe NOT match
[ 1.781044@0] usb1: type: 1, speed: 0, config: 0, dma: 0, id: 1, phy: fe108820, ctrl: fe080000
[ 1.789573@0] USB (1) use clock source: XTAL input
[ 1.815411@0] Core Release: 3.10a
[ 1.815441@0] Setting default values for core params
[ 1.818035@0] curmode: 1, host_only: 1
[ 1.830214@1] hdmitx: system: gate/pwr cmd: 5
[ 1.830249@1] hdmitx: edid: edid ready
[ 1.832661@1] hdmitx: edid: check sum valid
[ 1.836818@1] hdmitx: edid: check sum valid
[ 1.840996@1] hdmitx: edid: blk0 raw data
[ 1.841893@0] Using Buffer DMA mode
[ 1.841897@0] OTG VER PARAM: 1, OTG VER FLAG: 1
[ 1.841899@0] Working on port type = HOST
[ 1.856956@0] 00ffffffff[ 1.859187@0] dwc_otg lm1: DWC OTG Controller
[ 1.859204@0] dwc_otg lm1: new USB bus registered, assigned bus number 1
[ 1.859223@0] dwc_otg lm1: irq 63, io mem 0x00000000
[ 1.859226@0] -------hcd->flags.d32 = 0
[ 1.859247@0] Init: Port Power? op_state=1
[ 1.859248@0] Init1: Power Port (0)
[ 1.859345@0] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.859350@0] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.859354@0] usb usb1: Product: DWC OTG Controller
[ 1.859357@0] usb usb1: Manufacturer: Linux 3.10.33 dwc_otg_hcd
[ 1.859360@0] usb usb1: SerialNumber: lm1
[ 1.859636@0] hub 1-0:1.0: USB hub found
[ 1.859645@0] hub 1-0:1.0: 1 port detected
[ 1.859814@0] usb0: type: 0, speed: 0, config: 0, dma: 0, id: 0, phy: fe108800, ctrl: fe040000
[ 1.859823@0] USB (0) use clock source: XTAL input
[ 1.880882@0] Core Release: 3.10a
[ 1.880885@0] Setting default values for core params
[ 1.880891@0] curmode: 1, host_only: 0
[ 1.940973@0] Using Buffer DMA mode
[ 1.940976@0] OTG VER PARAM: 1, OTG VER FLAG: 1
[ 1.940979@0] Working on port type = OTG
[ 1.940980@0] Current port type: SLAVE
ffff[ 1.964731@0] dwc_otg lm0: DWC OTG Controller
[ 1.964745@0] dwc_otg lm0: new USB bus registered, assigned bus number 2
[ 1.964761@0] dwc_otg lm0: irq 62, io mem 0x00000000
[ 1.964795@0] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.964799@0] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.964803@0] usb usb2: Product: DWC OTG Controller
[ 1.964806@0] usb usb2: Manufacturer: Linux 3.10.33 dwc_otg_hcd
[ 1.964810@0] usb usb2: SerialNumber: lm0
[ 1.965060@0] hub 2-0:1.0: USB hub found
[ 1.965077@0] hub 2-0:1.0: 1 port detected
[ 1.965190@0] Dedicated Tx FIFOs mode
0014e101[ 2.022067@0] using timer detect id change, ed8f9800
[ 2.022169@0] boot_device_flag : 0
[ 2.022171@0] ===========================================amlnf_init:643,nand device tree ok,dev-name:nand
[ 2.022179@0] Nand PHY driver Version: 2.01.001.0006 (c) 2013 Amlogic Inc.
[ 2.022183@0] amlnf_phy_init : amlnf init flag 0
[ 2.022249@0] ######STS IRQ mode for nand driver
[ 2.022303@0] NAND device id: 2c 64 44 4b a9 0 0 0
[ 2.022308@0] detect NAND device: B revision NAND 8GiB MT29F64G08CBABA
[ 2.037270@0] status:0
[ 2.037276@0] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.10.33-gfa4a182-dirty #2
[ 2.037299@0] [<c00148e8>] (unwind_backtrace+0x0/0xf4) from [<c0011984>] (show_stack+0x10/0x14)
[ 2.037309@0] [<c0011984>] (show_stack+0x10/0x14) from [<c04c6b20>] (controller_quene_rb+0x1c0/0x1d0)
[ 2.037317@0] [<c04c6b20>] (controller_quene_rb+0x1c0/0x1d0) from [<c04bd4f8>] (nand_reset+0xd0/0x1c4)
[ 2.037323@0] [<c04bd4f8>] (nand_reset+0xd0/0x1c4) from [<c04bd860>] (read_id+0x68/0x144)
[ 2.037329@0] [<c04bd860>] (read_id+0x68/0x144) from [<c04bcdf4>] (amlnand_chip_init+0x360/0x72c)
[ 2.037335@0] [<c04bcdf4>] (amlnand_chip_init+0x360/0x72c) from [<c04c5a0c>] (amlnf_phy_init+0x180/0x204)
[ 2.037345@0] [<c04c5a0c>] (amlnf_phy_init+0x180/0x204) from [<c04b729c>] (amlnf_init+0xd4/0x12c)
[ 2.037357@0] [<c04b729c>] (amlnf_init+0xd4/0x12c) from [<c02f6cf4>] (driver_probe_device+0xd0/0x214)
[ 2.037366@0] [<c02f6cf4>] (driver_probe_device+0xd0/0x214) from [<c02f6ee4>] (__driver_attach+0x68/0x8c)
[ 2.037374@0] [<c02f6ee4>] (__driver_attach+0x68/0x8c) from [<c02f5298>] (bus_for_each_dev+0x4c/0x98)
[ 2.037381@0] [<c02f5298>] (bus_for_each_dev+0x4c/0x98) from [<c02f640c>] (bus_add_driver+0xd0/0x258)
[ 2.037388@0] [<c02f640c>] (bus_add_driver+0xd0/0x258) from [<c02f74f4>] (driver_register+0xa8/0x13c)
[ 2.037395@0] [<c02f74f4>] (driver_register+0xa8/0x13c) from [<c0008564>] (do_one_initcall+0xa8/0x150)
[ 2.037407@0] [<c0008564>] (do_one_initcall+0xa8/0x150) from [<c0b84bdc>] (kernel_init_freeable+0x138/0x1e0)
[ 2.037417@0] [<c0b84bdc>] (kernel_init_freeable+0x138/0x1e0) from [<c07dee30>] (kernel_init+0x8/0x158)
[ 2.037426@0] [<c07dee30>] (kernel_init+0x8/0x158) from [<c000dcd8>] (ret_from_fork+0x14/0x3c)
[ 2.040023@3] HOST mode
[ 2.052446@0] status:0
[ 2.052450@0] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.10.33-gfa4a182-dirty #2
[ 2.052461@0] [<c00148e8>] (unwind_backtrace+0x0/0xf4) from [<c0011984>] (show_stack+0x10/0x14)
[ 2.052468@0] [<c0011984>] (show_stack+0x10/0x14) from [<c04c6b20>] (controller_quene_rb+0x1c0/0x1d0)
[ 2.052475@0] [<c04c6b20>] (controller_quene_rb+0x1c0/0x1d0) from [<c04bd4f8>] (nand_reset+0xd0/0x1c4)
[ 2.052480@0] [<c04bd4f8>] (nand_reset+0xd0/0x1c4) from [<c04bd860>] (read_id+0x68/0x144)
[ 2.052486@0] [<c04bd860>] (read_id+0x68/0x144) from [<c04bcdf4>] (amlnand_chip_init+0x360/0x72c)
[ 2.052492@0] [<c04bcdf4>] (amlnand_chip_init+0x360/0x72c) from [<c04c5a0c>] (amlnf_phy_init+0x180/0x204)
[ 2.052499@0] [<c04c5a0c>] (amlnf_phy_init+0x180/0x204) from [<c04b729c>] (amlnf_init+0xd4/0x12c)
[ 2.052508@0] [<c04b729c>] (amlnf_init+0xd4/0x12c) from [<c02f6cf4>] (driver_probe_device+0xd0/0x214)
[ 2.052516@0] [<c02f6cf4>] (driver_probe_device+0xd0/0x214) from [<c02f6ee4>] (__driver_attach+0x68/0x8c)
[ 2.052523@0] [<c02f6ee4>] (__driver_attach+0x68/0x8c) from [<c02f5298>] (bus_for_each_dev+0x4c/0x98)
[ 2.052529@0] [<c02f5298>] (bus_for_each_dev+0x4c/0x98) from [<c02f640c>] (bus_add_driver+0xd0/0x258)
[ 2.052536@0] [<c02f640c>] (bus_add_driver+0xd0/0x258) from [<c02f74f4>] (driver_register+0xa8/0x13c)
[ 2.052543@0] [<c02f74f4>] (driver_register+0xa8/0x13c) from [<c0008564>] (do_one_initcall+0xa8/0x150)
[ 2.052552@0] [<c0008564>] (do_one_initcall+0xa8/0x150) from [<c0b84bdc>] (kernel_init_freeable+0x138/0x1e0)
[ 2.052559@0] [<c0b84bdc>] (kernel_init_freeable+0x138/0x1e0) from [<c07dee30>] (kernel_init+0x8/0x158)
[ 2.052566@0] [<c07dee30>] (kernel_init+0x8/0x158) from [<c000dcd8>] (ret_from_fork+0x14/0x3c)
[ 2.067503@0] status:0
[ 2.067507@0] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.10.33-gfa4a182-dirty #2
[ 2.067516@0] [<c00148e8>] (unwind_backtrace+0x0/0xf4) from [<c0011984>] (show_stack+0x10/0x14)
[ 2.067523@0] [<c0011984>] (show_stack+0x10/0x14) from [<c04c6b20>] (controller_quene_rb+0x1c0/0x1d0)
[ 2.067529@0] [<c04c6b20>] (controller_quene_rb+0x1c0/0x1d0) from [<c04bd4f8>] (nand_reset+0xd0/0x1c4)
[ 2.067534@0] [<c04bd4f8>] (nand_reset+0xd0/0x1c4) from [<c04bd860>] (read_id+0x68/0x144)
[ 2.067540@0] [<c04bd860>] (read_id+0x68/0x144) from [<c04bcdf4>] (amlnand_chip_init+0x360/0x72c)
[ 2.067546@0] [<c04bcdf4>] (amlnand_chip_init+0x360/0x72c) from [<c04c5a0c>] (amlnf_phy_init+0x180/0x204)
[ 2.067553@0] [<c04c5a0c>] (amlnf_phy_init+0x180/0x204) from [<c04b729c>] (amlnf_init+0xd4/0x12c)
[ 2.067561@0] [<c04b729c>] (amlnf_init+0xd4/0x12c) from [<c02f6cf4>] (driver_probe_device+0xd0/0x214)
[ 2.067568@0] [<c02f6cf4>] (driver_probe_device+0xd0/0x214) from [<c02f6ee4>] (__driver_attach+0x68/0x8c)
[ 2.067575@0] [<c02f6ee4>] (__driver_attach+0x68/0x8c) from [<c02f5298>] (bus_for_each_dev+0x4c/0x98)
[ 2.067581@0] [<c02f5298>] (bus_for_each_dev+0x4c/0x98) from [<c02f640c>] (bus_add_driver+0xd0/0x258)
[ 2.067588@0] [<c02f640c>] (bus_add_driver+0xd0/0x258) from [<c02f74f4>] (driver_register+0xa8/0x13c)
[ 2.067595@0] [<c02f74f4>] (driver_register+0xa8/0x13c) from [<c0008564>] (do_one_initcall+0xa8/0x150)
[ 2.067603@0] [<c0008564>] (do_one_initcall+0xa8/0x150) from [<c0b84bdc>] (kernel_init_freeable+0x138/0x1e0)
[ 2.067610@0] [<c0b84bdc>] (kernel_init_freeable+0x138/0x1e0) from [<c07dee30>] (kernel_init+0x8/0x158)
[ 2.067616@0] [<c07dee30>] (kernel_init+0x8/0x158) from [<c000dcd8>] (ret_from_fork+0x14/0x3c)
[ 2.069954@3] -------hcd->flags.d32 = 0
[ 2.069974@3] Init: Port Power? op_state=1
[ 2.069975@3] Init1: Power Port (0)
[ 2.069980@3] [RN5T618]rn5t618_otg_change, driver is not ready, do it later
[ 2.069982@3] set usb port power on (board gpio 15)!
[ 2.559785@1] 00Indeed it is in host mode hprt0 = 00021501
[ 2.565405@3] 0000000011170103800002781acf74a3574cb023
[ 2.570498@3] 09484c00000081c0d1c0010101010101010101010101023a801871382d40582c
[ 2.577692@3] 4500c48e2100[ 2.580110@0] AML_NAND_NEW_OOB : new oob
[ 2.580115@0] bus_cycle=6, bus_timing=8,system=3.9ns,flash->T_REA =16,flash->T_RHOH=15
[ 2.580118@0] boot_device_flag = 0
[ 2.582486@0] NAND CKECK : arg nbbt: arg_valid= 1, valid_blk_addr = 9, valid_page_addr = 0
[ 2.585595@0] nand block at blk 4 is bad
[ 2.585597@0] nand block at blk 5 is bad
[ 2.585599@0] nand block at blk 6 is bad
[ 2.585600@0] nand block at blk 7 is bad
[ 2.586883@0] NAND CKECK : arg ncnf: arg_valid= 1, valid_blk_addr = 10, valid_page_addr = 0
[ 2.587220@0] nand shipped bbt at block 0
[ 2.587222@0] nand block at blk 4 is bad
[ 2.587224@0] nand block at blk 5 is bad
[ 2.587226@0] nand block at blk 6 is bad
[ 2.587227@0] nand block at blk 7 is bad
[ 2.602862@0] NAND CKECK : arg phyp: arg_valid= 1, valid_blk_addr = 11, valid_page_addr = 1
[ 2.603272@0] nand block at blk 4 is bad
[ 2.603274@0] nand block at blk 5 is bad
[ 2.603276@0] nand block at blk 6 is bad
[ 2.603278@0] nand block at blk 7 is bad
[ 2.632852@0] NAND CKECK : arg nkey: arg_valid= 1, valid_blk_addr = 8, valid_page_addr = 43
[ 2.633198@0] i=0,register --- nand_key
[ 2.633208@0] nand blk 4 is shipped bad block
[ 2.633210@0] nand blk 5 is shipped bad block
[ 2.633211@0] nand blk 6 is shipped bad block
[ 2.633213@0] nand blk 7 is shipped bad block
[ 2.633233@0] amlnand_phydev_init,1177,phydev->offset=6800000,phydev->size=24800000
[ 2.633236@0] amlnand_phydev_init,1177,phydev->offset=2b000000,phydev->size=51800000
[ 2.633240@0] amlnand_phydev_init,1177,phydev->offset=7c800000,phydev->size=183800000
[ 2.633244@0] nfcache : offset: 0x000006800000 -0x000024800000 : partitons 1 : single_chip multi_plane
[ 2.633248@0] nfcode : offset: 0x00002b000000 -0x000051800000 : partitons 5 : single_chip multi_plane
[ 2.633252@0] nfdata : offset: 0x00007c800000 -0x000183800000 : partitons 1 : single_chip multi_plane
[ 2.633253@0] amlnand_add_nftl:
[ 2.633255@0] Creating 1 ntd partitions
[ 2.633259@0] block_num 146
[ 2.635940@0] ------init_ntd
[ 2.636128@0] ntd: Giving out device 0 to nfcache
[ 2.636130@0] Creating 5 ntd partitions
[ 2.636133@0] block_num 326
[ 2.642281@0] ntd: Giving out device 1 to nfcode
[ 2.642283@0] Creating 1 ntd partitions
[ 2.642286@0] block_num 1550
[ 2.670891@0] ntd: Giving out device 2 to nfdata
[ 2.671167@0] ethernet_driver probe!
[ 2.671172@0] Please config phy interface.
[ 2.671173@0] Please config savepowermode.
[ 2.671175@0] Please config reset_pin_enable.
[ 2.671176@0] Please config reset_delay.
[ 2.671178@0] Please config reset_pin.
[ 2.671181@0] ethernetinit(dbg[c0c3d7e4]=1)
[ 2.671202@0] ethernet base addr is fe0c0000
[ 2.671216@0] write mac add to:ed932ac8: ea 95 73 92 cb 01 |..s...|
[ 2.673599@0] libphy: AMLMAC MII Bus: probed
[ 2.673604@0] eth0: PHY ID 02430c54 at 0 IRQ -1 (0:00) active
[ 2.674036@0] Amlogic A/V streaming port init
[ 2.674739@0] buffersize=262144,0,start=0
[ 2.674747@0] Subtitle stbuf alloced at 0xece40000, size = 262144
[ 2.674749@0] changed the (2) buffer size from 0 to 262144
[ 2.674875@0] init vdec memsource 9a00000->199fffff
[ 2.674953@0] [tsync_pcr_init]init success.
[ 2.674955@0] amvideocap_init_module
[ 2.674983@0] amvideocap_probe,amvideocap
[ 2.674986@0] amvideocap_dev_register buf:1d200000,size:800000.
[ 2.675154@0] regist mpeg12 codec profile
[ 2.675188@0] regist mpeg4 codec profile
[ 2.675190@0] amvdec_vc1 module init
[ 2.675221@0] regist vc1 codec profile
[ 2.675223@0] amvdec_h264 module init
[ 2.675281@0] regist h264 codec profile
[ 2.675283@0] amvdec_h264mvc module init
[ 2.675317@0] regist hmvc codec profile
[ 2.675318@0] amvdec_h264_4k2k module init
[ 2.675358@0] regist h264_4k2k codec profile
[ 2.675359@0] amvdec_h265 module init
[ 2.675394@0] regist hevc_unsupport codec profile
[ 2.675428@0] regist mjpeg codec profile
[ 2.675430@0] amvdec_real module init
[ 2.675463@0] amvdec_avs module init
[ 2.675553@0] amvenc_avc memory resource undefined.
[ 2.675554@0] encode_wq_init.
[ 2.675557@0] encode start monitor.
[ 2.675600@2] encode workqueue monitor start.
[ 2.675739@0] jpegenc module init
[ 2.675906@0] picdec buffer size is 4000000
[ 2.676020@0] alloc_keep_buffer keep_y_addr eca00000
[ 2.676034@0] alloc_keep_buffer keep_u_addr ecf00000
[ 2.676042@0] alloc_keep_buffer keep_v_addr ed000000
[ 2.676044@0] yaddr=eca00000,u_addr=ecf00000,v_addr=ed000000
[ 2.676222@0] create_ge2d_work_queue video task ok
[ 2.676225@0] video2_init enter
[ 2.676494@0] video2_drv_probe exit
[ 2.676739@0]
[ 2.676739@0]
[ 2.676739@0] VECM init
[ 2.676739@0]
[ 2.676877@0] efuse===========================================
[ 2.676959@0] efuse: device efuse created
[ 2.676999@0] efuse--------------------------------------------
[ 2.677000@0] SARADC Driver init.
[ 2.677079@0] __saradc_probe__
[ 2.729970@3] usb 1-1: new high-speed USB device number 2 using dwc_otg
[ 2.730275@0] Indeed it is in host mode hprt0 = 00001101
[ 2.820060@0] saradc calibration: ref_val = 507
[ 2.820062@0] saradc calibration: ref_nominal = 512
[ 2.820064@0] saradc calibration: coef = 4112
[ 2.820255@0] irblaster probe
[ 2.820356@0] Remote Driver
[ 2.820420@0] Remote platform_data g_remote_base=fe600580
[ 2.820442@0] set drvdata completed
[ 2.820449@0] device_create_file completed
[ 2.820747@0] input: aml_keypad as /devices/platform/meson-remote/input/input0
[ 2.820899@0] input_register_device completed
[ 2.820948@0] [0xffffff00] = 0x1dd0190
[ 2.820950@0] [0xffffff04] = 0xf800ca
[ 2.820952@0] [0xffffff08] = 0x82006e
[ 2.820954@0] [0xffffff0c] = 0x3c0030
[ 2.820955@0] [0xffffff10] = 0x30fa0013
[ 2.820956@0] [0xffffff18] = 0x6f19000
[ 2.820958@0] [0xffffff1c] = 0xbe40
[ 2.820960@0] [0x0] = 0xfa00a0
[ 2.820961@0] [0x4] = 0xfa00a0
[ 2.820963@0] [0x8] = 0xfa00a0
[ 2.820964@0] [0xc] = 0x640030
[ 2.820965@0] [0x10] = 0x30fa0013
[ 2.820967@0] [0x18] = 0x961b800
[ 2.820968@0] [0x1c] = 0x9740
[ 2.820970@0] [0x20] = 0x104
[ 2.820971@0] [0x24] = 0x0
[ 2.820972@0] [0x28] = 0x0
[ 2.820975@0] set_remote_mode[69]
[ 2.820989@0] remote config major:232
[ 2.821063@0] physical address:0x2d0a8000
[ 2.821089@0] ADC Keypad Driver init.
[ 2.821166@0] ==touch_ts_init==
[ 2.821234@0] ==ft5x0x_ts_init==
[ 2.821256@0] ==goodix_ts_init==
[ 2.821294@0] i2c-core: driver [gslx680_compatible] using legacy suspend method
[ 2.821296@0] i2c-core: driver [gslx680_compatible] using legacy resume method
[ 2.821315@0] !!!ntp_ts: ret = 0.
[ 2.821316@0] VTL ct36x TouchScreen driver, <[email protected]>.
[ 2.821332@0] i2c-core: driver [ct36x] using legacy suspend method
[ 2.821334@0] i2c-core: driver [ct36x] using legacy resume method
[ 2.821337@0] VTL ct36x TouchScreen driver End.
[ 2.821338@0] ==gsl_ts_init==
[ 2.821355@0] ret=0
[ 2.821405@0] ####################come here #####################
[ 2.836916@0] up vfd key(103) registed.
[ 2.836918@0] down vfd key(108) registed.
[ 2.836920@0] right vfd key(106) registed.
[ 2.836922@0] back vfd key(158) registed.
[ 2.836924@0] left vfd key(105) registed.
[ 2.836925@0] ok vfd key(232) registed.
[ 2.837033@0] input: vfd_keypad as /devices/platform/m1-vfd.0/input/input1
[ 2.837125@0] vfd config major:231
[ 2.837380@0] i2c-core: driver [mir3da] using legacy suspend method
[ 2.837382@0] i2c-core: driver [mir3da] using legacy resume method
[ 2.837401@0] i2c-core: driver [lis3dh_acc] using legacy suspend method
[ 2.837403@0] i2c-core: driver [lis3dh_acc] using legacy resume method
[ 2.837435@0] i2c-core: driver [bma222] using legacy suspend method
[ 2.837437@0] i2c-core: driver [bma222] using legacy resume method
[ 2.837469@0] i2c-core: driver [dmard06] using legacy suspend method
[ 2.837471@0] i2c-core: driver [dmard06] using legacy resume method
[ 2.837489@0] lsm303d driver: init
[ 2.837528@0] i2c-core: driver [dmard10] using legacy suspend method
[ 2.837529@0] i2c-core: driver [dmard10] using legacy resume method
[ 2.837548@0] stk8313_init
[ 2.837565@0] ======stk831x init ok======
[ 2.837567@0] stk831x_init
[ 2.837584@0] mxc622x accelerometer driver: init
[ 2.837600@0] i2c-core: driver [mxc622x] using legacy suspend method
[ 2.837602@0] i2c-core: driver [mxc622x] using legacy resume method
[ 2.837605@0] mxc6255xc accelerometer driver: init
[ 2.837621@0] i2c-core: driver [mxc6255xc] using legacy suspend method
[ 2.837623@0] i2c-core: driver [mxc6255xc] using legacy resume method
[ 2.837671@0] cm3217 v.1.0.0.1
[ 2.837691@0] i2c-core: driver [elan_epl6814] using legacy suspend method
[ 2.837693@0] i2c-core: driver [elan_epl6814] using legacy resume method
[ 2.837711@0] i2c-core: driver [LTR501] using legacy suspend method
[ 2.837712@0] i2c-core: driver [LTR501] using legacy resume method
[ 2.837763@0] GPIO Keypad Driver init.
[ 2.837820@0] ==gpio_key_probe==
[ 2.837840@0] reg:2620,clearmask=400040,setmask=1
[ 2.837843@0] reg:2622,clearmask=ff0000,set pin=3
[ 2.837845@0] reg:2623,clearmask=7000000,setmask=7
[ 2.837848@0] reg:2620,clearmask=800080,setmask=10001
[ 2.837851@0] reg:2622,clearmask=ff000000,set pin=3
[ 2.837853@0] reg:2623,clearmask=70000000,setmask=7
[ 2.837898@0] power key(116) registed.
[ 2.838000@0] input: gpio_keypad as /devices/platform/gpio_keypad.6/input/input2
[ 2.838077@0] gpio keypad register input device completed.
[ 2.838082@0] gpio keypad major:230
[ 2.838191@0] spi_nor_init
[ 2.838257@0] amlogic_spi_nor_probe:
[ 2.838262@0] amlogic_spi->state_name:default
[ 2.838328@0] AMLOGIC_SPI_NOR cc000000.spi: master is unqueued, this is deprecated
[ 2.838382@0] check_storage_device : spi boot_device_flag : 0
[ 2.838383@0] spi_nor_probe
[ 2.838411@0] spi_nor apollospi:32766: mx25l160 (2048 Kbytes)
[ 2.838549@0] Creating 2 MTD partitions on "apollospi:32766":
[ 2.838554@0] 0x000000000000-0x000000100000 : "bootloader"
[ 2.839063@0] 0x000000100000-0x000000110000 : "ubootenv"
[ 2.839523@0] amlogic_spi_nor_probe over
[ 2.839627@0] mmc driver version: 1.07, 2015-01-21: fix a bug in tuning which caused eMMC data CRC error
[ 2.931144@0] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608
[ 2.931149@0] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 2.931153@0] usb 1-1: Product: USB2.0 Hub
[ 2.931588@0] hub 1-1:1.0: USB hub found
[ 2.931857@0] hub 1-1:1.0: 4 ports detected
[ 3.089973@2] Indeed it is in host mode hprt0 = 00021501
[ 3.269954@2] usb 2-1: new high-speed USB device number 2 using dwc_otg
[ 3.270236@0] Indeed it is in host mode hprt0 = 00001101
[ 3.471636@0] usb 2-1: New USB device found, idVendor=05e3, idProduct=0718
[ 3.471641@0] usb 2-1: New USB device strings: Mfr=0, Product=1, SerialNumber=2
[ 3.471645@0] usb 2-1: Product: USB Storage
[ 3.471648@0] usb 2-1: SerialNumber: 000000000033
[ 3.472106@0] usb-storage 2-1:1.0: UÓ‚Å] hdmitx: audio: i2s_to_spdif_flag:1
[ 3.788110@1] hdmitx: audio: Enable audio spdif to HDMI
[ 3.789943@2] [0;40;33m Uart in[0m
[ 3.789946@2] [aml_uart_switch] aml_uart_switch 1
[ 3.789946@2]
[ 3.789946@2]
[ 3.789946@2]
[ 3.789946@2]
[ 3.789949@2] [0;40;32m JTAG in[0m
[ 3.811828@1] hdmitx: cec: CEC not ready
[ 3.815677@1] hdmi detect: plug.
[ 3.829973@2] reg:2620,clearmask=80008,setmask=10001
[ 3.830014@2] reg:2621,clearmask=ff000000,set pin=64
[ 3.834325@2] reg:2623,clearmask=7000,setmask=7
[ 3.838833@2] reg:2620,clearmask=200020,setmask=1
[ 3.842897@0] usb 1-1.3: New USB device found, idVendor=046d, idProduct=c52b
[ 3.842902@0] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 3.842906@0] usb 1-1.3: Product: USB Receiver
[ 3.842909@0] usb 1-1.3: Manufacturer: Logitech
[ 3.867004@2] reg:2622,clearmask=ff00,set pin=64
[ 3.871598@2] reg:2623,clearmask=700000,setmask=7
[ 3.876576@2] pdata->caps 107
[ 3.879227@2] pdata->caps2 0
[ 3.882098@2] get property: port, value:0x00000000
[ 3.888588@2] get property: ocr_avail, value:0x00200000
[ 3.895103@2] get property: f_min, value:0x000493e0
[ 3.901616@2] get property: f_max, value:0x02faf080
[ 3.908105@2] get property: max_req_size, value:0x00020000
[ 3.914645@2] get property: pinname, str:sdio
[ 3.920432@2] get property: card_type, value:0x00000003
[ 3.920474@0] logitech-djreceiver 0003:046D:C52B.0003: hiddev0,hidraw0: USB HID v1.11 Device [Logitech USB Receiver] on usb-lm1-1.3/input2
[ 4.029943@2] [aml_sdio_probe] aml_sdio_probe() success!
[ 4.031139@2] host->base fe108e00
[ 4.032958@2] pdata->caps 80000547
[ 4.036290@2] pdata->caps2 0
[ 4.039151@2] get property: port, value:0x00000005
[ 4.045664@2] get property: ocr_avail, value:0x00200000
[ 4.052160@2] get property: f_min, value:0x000493e0
[ 4.058654@2] get property: f_max, value:0x05f5e100
[ 4.065162@2] get property: max_req_size, value:0x00020000
[ 4.071666@2] get property: pinname, str:emmc
[ 4.077464@2] get property: card_type, value:0x00000001
[ 4.083974@2] get property: gpio_dat3, str:BOOT_3
[ 4.089968@2] [is_emmc_exist] host->storage_flag=4, POR_BOOT_VALUE=5
[ 4.096274@2] [aml_sdhc_probe]: there is not eMMC/tsd, skip sdhc_c dts config!
[ 4.159944@2] [aml_sdhc_probe] aml_sdhc_probe() success!
[ 4.160037@2] [dsp]DSP start addr 0xc5e00000
[ 4.163884@2] [dsp]register dsp to char divece(257)
[ 4.168932@2] amlogic audio spdif interface device init!
[ 4.174075@2] name=nand_key nand_key
[ 4.177929@2] register_aes_algorithm:488,new way
[ 4.182628@2] key name:keyexample, key data:1234567890
[ 4.187851@2] aml_rtc rtc.0: rtc core: registered aml_rtc as rtc0
[ 4.195974@2] input: rn5t618_pmu as /devices/i2c-0/0-0032/rn5t618_pmu.0/input/input3
[ 4.201153@2] [RN5T618] NO BATTERY_PARAMETERS FOUND
[ 4.205902@2] [RN5T618]no battery, exit
[ 4.215758@2] vdin_drv_init: major 228
[ 4.215933@2] vdin0 mem_start = 0x19a00000, mem_size = 0x1000000
[ 4.219858@2] vdin_drv_probe: driver initialized ok
[ 4.224813@2] vdin1 mem_start = 0x1aa00000, mem_size = 0x1000000
[ 4.230702@2] vdin_drv_probe: driver initialized ok
[ 4.235606@2] amvdec_656in module: init.
[ 4.239441@2] amvdec_656in_init_module:major 227
[ 4.244270@2] amvdec_656in probe ok.
[ 4.247797@2] amvdec_csi probe ok.
[ 4.250993@2] [viuin..]viuin_init_module viuin module init
[ 4.256539@2] [viuin..]viuin_probe probe ok.
[ 4.260850@2] [isp..]isp_probe isp probe ok.
[ 4.264935@2] [sii9233a_drv_init] Ver: 2013Nov12
[ 4.270108@2] amaudio2: device amaudio2 created
[ 4.274158@2] Error: Didn't get power valid value --- wifi_power_probe 376
[ 4.280886@2] Error: Didn't get suspend_power_off value --- wifi_power_probe 393
[ 4.288243@2] wifi_power power_gpio is 6
[ 4.292151@2] wifi_power power_gpio2 is 123
[ 4.296437@2] amlogic rfkill init
[ 4.299644@2] not get gpio_en
[ 4.302554@2] not get gpio_wake
[ 4.330003@2] wifi_request_32k_clk : OFF-->ON for bt_rfkill
[ 4.330039@2] clock_32k_pin(122) : (null)
[ 4.333927@2] clock_32k_pin(122) : sdio_wifi
[ 4.440945@2] aml_aes aml_aes: Aml AES
[ 4.441284@2] aml_tdes aml_tdes: Aml TDES
[ 4.443323@2] usbcore: registered new interface driver snd-usb-audio
[ 4.449597@2] enter rt5616_modinit
[ 4.452877@2] dummy_codec_platform_probe
[ 4.456764@2] == ES8323 == es8323_modinit()
[ 4.461263@2] i2s get no clk src setting in dts, use the default mpll 0
[ 4.467494@2] [aml-i2s-dai]enterd aml_i2s_dai_probe,old_samplerate:0,sample_rate=48000
[ 4.475530@2] [aml-spdif-dai]enter aml_dai_spdif_init
[ 4.480415@2] [aml-spdif-dai]enterd aml_spdif_play,set_clock:-1,sample_rate=4
[ 4.487511@2] audio_set_958_clk, freq=4,
[ 4.491427@2] IEC958 16bit
[ 4.494101@2] hdmitx: audio: aout notify rate 48000
[ 4.498953@2] hdmitx: audio: aout notify size 16
[ 4.503559@2] hdmitx: audio: aout notify format CT_PCM
[ 4.508663@2] hdmitx: audio: audio channel num is 1
[ 4.513527@2] hdmitx: audio: SPDIF
[ 4.516905@2] hdmitx: audio: current VIC: 16
[ 4.521151@2] hdmitx: audio: audio sample rate: 3
[ 4.525825@2] hdmitx: audio: set audio N para
[ 4.530170@2] hdmitx: audio: PCM out to HDMI
[ 4.534407@2] hdmitx: audio: i2s_to_spdif_flag:1
[ 4.539087@2] hdmitx: audio: Enable audio spdif to HDMI
[ 4.544298@2] hdmitx: audio: Audio Type: PCM
[ 4.548576@2] hdmitx: audio: set audio param
[ 4.552850@2] [aml-spdif-dai]aml_spdif_probe
[ 4.557125@2] test codec dummy_codec
[ 4.560596@2] using external codec, index = 1
[ 4.564918@2] using external dummy codec
[ 4.568900@2] enter spdif_dit_probe
[ 4.572381@2] aml_spdif_unmute
[ 4.575631@2] codec_name = dummy_codec.0
[ 4.579665@2] p_aml_audio->hp_disable=1
[ 4.583221@2] falied to get spk event delay time paraments from dts file
[ 4.589883@2] spk_event delay_time = 0
[ 4.594718@2] aml-i2s 0:playback preallocate_dma_buffer: area=ef300000, addr=2f500000, size=524288
[ 4.602860@2] aml-i2s 1:capture preallocate_dma_buffer: area=ef240000, addr=2f440000, size=65536
[ 4.611320@2] aml_snd_m8 aml_m8_sound_card.5: dummy_codec <-> aml-i2s-dai.0 mapping ok
[ 4.620606@2] aml-i2s 0:playback preallocate_dma_buffer: area=ef400000, addr=2f600000, size=524288
[ 4.628512@2] aml-i2s 1:capture preallocate_dma_buffer: area=ef260000, addr=2f460000, size=65536
[ 4.636976@2] aml_snd_m8 aml_m8_sound_card.5: dit-hifi <-> aml-spdif-dai.0 mapping ok
[ 4.645611@2] -----ext_codec=1---
[ 4.648147@2] =aml_m8_pinmux_init==,aml_m8_pinmux_init done,---0
[ 4.654240@2] GACT probability NOT on
[ 4.657760@2] Mirror/redirect action on
[ 4.661607@2] u32 classifier
[ 4.664430@2] Actions configured
[ 4.667986@2] Netfilter messages via NETLINK v0.30.
[ 4.672886@2] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 4.679452@2] ctnetlink v0.93: registering with nfnetlink.
[ 4.684603@2] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
[ 4.691657@2] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
[ 4.697904@2] xt_time: kernel timezone is -0000
[ 4.702224@2] ipip: IPv4 over IPv4 tunneling driver
[ 4.707374@2] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 4.712578@2] arp_tables: (C) 2002 David S. Miller
[ 4.717248@2] TCP: cubic registered
[ 4.720697@2] Initializing XFRM netlink socket
[ 4.725451@2] NET: Registered protocol family 10
[ 4.730233@2] mip6: Mobile IPv6
[ 4.732841@2] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 4.738517@2] sit: IPv6 over IPv4 tunneling driver
[ 4.743771@2] NET: Registered protocol family 17
[ 4.747751@2] NET: Registered protocol family 15
[ 4.752390@2] Bridge firewalling registered
[ 4.756584@2] Bluetooth: RFCOMM TTY layer initialized
[ 4.761547@2] Bluetooth: RFCOMM socket layer initialized
[ 4.766802@2] Bluetooth: RFCOMM ver 1.11
[ 4.770713@2] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 4.776164@2] Bluetooth: BNEP filters: protocol multicast
[ 4.781550@2] Bluetooth: BNEP socket layer initialized
[ 4.786653@2] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 4.792733@2] Bluetooth: HIDP socket layer initialized
[ 4.797857@2] l2tp_core: L2TP core driver, V2.0
[ 4.802360@2] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[ 4.807282@2] l2tp_ip: L2TP IP encapsulation support (L2TPv3)
[ 4.813026@2] l2tp_netlink: L2TP netlink interface
[ 4.817789@2] l2tp_eth: L2TP ethernet pseudowire support (L2TPv3)
[ 4.823870@2] l2tp_debugfs: L2TP debugfs support
[ 4.828434@2] l2tp_ip6: L2TP IP encapsulation support for IPv6 (L2TPv3)
[ 4.835058@2] NET: Registered protocol family 35
[ 4.840285@2] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[ 4.847430@2] Registering SWP/SWPB emulation handler
[ 4.852370@2] enter meson_pm_init
[ 4.855779@2] enter meson_pm_probe!
[ 4.859123@2] meson_pm_probe done !
[ 4.863085@2] file system registered
[ 4.866758@2] android_usb gadget: Mass Storage Function, version: 2009/09/11
[ 4.873179@2] android_usb gadget: Number of LUNs=2
[ 4.877931@2] lun0: LUN: removable file: (no medium)
[ 4.882966@2] lun1: LUN: removable file: (no medium)
[ 4.888131@2] android_usb gadget: android_usb ready
[ 4.893261@2] aml_rtc rtc.0: setting system clock to 1970-01-01 00:00:00 UTC (0)
[ 4.900236@2] ### dt-test ### No testcase data in device tree; not running tests
[ 4.907667@2] meson_cpufreq: no voltage_control prop
[ 4.912523@2] voltage_control = 0
[ 4.916975@2] <<-GTP-INFO->> GTP driver installing...
[ 4.920917@2] hdmitx: cec: CEC init
[ 4.924452@2] input: cec_input as /devices/virtual/input/input4
[ 4.930277@2] hdmitx: cec: hdmitx_device->cec_init_ready:0x1[ 4.935666@2] hdmitx: cec: CEC task process
[ 4.9[ 4.959944@2] Changing uart_ao_ttyS0: baud from 0 to 115200
[ 4.980089@2] Freeing unused kernel memory: 380K (c0b84000 - c0be3000)
[ 5.002388@3] init: aml-firstboot-init insert aml-firstboot-init
[ 5.006811@3] aml_nftl_dev: module license 'Proprietary' taints kernel.
[ 5.009346@3] Disabling lock debugging due to kernel taint
[ 5.016007@3] boot_device_flag : 0
[ 5.018185@3] register_ntd_blktrans start
[ 5.022195@3] ntd device 250!
[ 5.025118@3] ntd->name: nfcache
[ 5.028328@3] adjust_block_num : 4,reserved_block_ratio 10
[ 5.033806@3] nftl version 150330d
[ 5.037166@3] nftl build Mar 30 2015_19:39:32
[ 5.041526@3] nftl part attr 0
[ 5.046680@3] nftl start:146,17, init flag 0
[ 5.048942@3] first
[ 5.099971@3] average_erase_count:0
[ 5.100001@3] second 6,129
[ 5.100510@3] part->max_discard_block = 4
[ 5.107843@3] current_block1:139
[ 5.190354@3] recover_current_block_mapping invalid page data!!
[ 5.191226@3] recover_current_block_mapping invalid page data!!
[ 5.197097@3] recover_current_block_mapping invalid page data!!
[ 5.202997@3] recover_current_block_mapping invalid page data!!
[ 5.208908@3] recover_current_block_mapping invalid page data!!
[ 5.214807@3] recover_current_block_mapping invalid page data!!
[ 5.220644@3] all discard block full!!
[ 5.223831@3] free block cnt = 140
[ 5.227211@3] new current block is 144
[ 5.578667@0] prio_garbage_collect_no_last_page_in_create_list put_phy_block_to_free_list!
[ 5.802538@0] recover_current_block_mapping : fill the current block, from page 255
[ 5.804554@0] total discard page count is 0
[ 5.808716@0] create_part_list:1238,current_used_discard_block=138,current_discard_block_used_count=8
[ 5.818343@0] unmappig_pages=31983,discarded_pages=0,mapping_pages=1041
[ 5.824525@0] nftl ok!
[ 5.827289@0] Enable QUEUE_FLAG_DISCARD for NFTL
[ 5.832102@0] aml_nftl_add_ntd ok
[ 5.834733@0] ntd device 250!
[ 5.837664@0] ntd->name: nfcode
[ 5.840832@0] adjust_block_num : 4,reserved_block_ratio 10
[ 5.846274@0] nftl version 150330d
[ 5.849629@0] nftl build Mar 30 2015_19:39:32
[ 5.854010@0] nftl part attr 0
[ 5.861945@0] size_in_blk 326; total_block 322;
[ 5.861970@0] nftl start:322,33, init flag 0
[ 5.866156@0] first
[ 5.909791@0] scsi 0:0:0:0: Direct-Access USB TO I DE/SATA Device 0016 PQ: 0 ANSI: 4
[ 5.914236@0] sd 0:0:0:0: [sda] Test WP failed, assume Write Enabled
[ 5.919290@0] sd 0:0:0:0: [sda] Asking for cache data failed
[ 5.924461@0] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 5.932762@0] sd 0:0:0:0: [sda] Test WP failed, assume Write Enabled
[ 5.937491@0] sd 0:0:0:0: [sda] Asking for cache data failed
[ 5.942624@0] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 5.948851@0] sd 0:0:0:0: [sda] Attached SCSI disk
[ 5.972036@1] average_erase_count:0
[ 5.972062@1] second 244,289
[ 5.972745@1] part->max_discard_block = 4
[ 6.115164@1] current_block1:76
[ 6.123763@1] recover_current_block_mapping invalid page data!!
[ 6.124621@1] recover_current_block_mapping invalid page data!!
[ 6.130539@1] recover_current_block_mapping invalid page data!!
[ 6.136427@1] recover_current_block_mapping invalid page data!!
[ 6.142312@1] recover_current_block_mapping invalid page data!!
[ 6.148204@1] recover_current_block_mapping invalid page data!!
[ 6.154070@1] all discard block full!!
[ 6.157285@1] free block cnt = 78
[ 6.160537@1] new current block is 79
[ 6.212995@2] [RN5T618]battery vol change: 0->0
[ 6.313875@0] prio_garbage_collect_no_last_page_in_create_list put_phy_block_to_free_list!
[ 6.732929@0] recover_current_block_mapping : fill the current block, from page 255
[ 6.734946@0] total discard page count is 0
[ 6.739112@0] create_part_list:1238,current_used_discard_block=77,current_discard_block_used_count=248
[ 6.749300@0] unmappig_pages=13401,discarded_pages=0,mapping_pages=60583
[ 6.755100@0] nftl ok!
[ 6.758038@0] Enable QUEUE_FLAG_DISCARD for NFTL
[ 6.762653@0] Enable QUEUE_FLAG_DISCARD for NFTL
[ 6.767137@0] Enable QUEUE_FLAG_DISCARD for NFTL
[ 6.771778@0] Enable QUEUE_FLAG_DISCARD for NFTL
[ 6.776289@0] Enable QUEUE_FLAG_DISCARD for NFTL
[ 6.780880@0] aml_nftl_add_ntd ok
[ 6.783662@0] ntd device 250!
[ 6.786609@0] ntd->name: nfdata
[ 6.789728@0] adjust_block_num : 4,reserved_block_ratio 10
[ 6.795226@0] nftl version 150330d
[ 6.798586@0] nftl build Mar 30 2015_19:39:32
[ 6.803028@0] nftl part attr 0
[ 6.829143@0] nftl start:1550,145, init flag 0
[ 6.830424@0] first
[ 7.345267@0] average_erase_count:0
[ 7.345307@0] second 323,1405
[ 7.346072@0] part->max_discard_block = 4
[ 7.533096@0] current_block1:1226
[ 7.609635@0] recover_current_block_mapping invalid page data!!
[ 7.610517@0] recover_current_block_mapping invalid page data!!
[ 7.616416@0] recover_current_block_mapping invalid page data!!
[ 7.622344@0] recover_current_block_mapping invalid page data!!
[ 7.628209@0] recover_current_block_mapping invalid page data!!
[ 7.634123@0] recover_current_block_mapping invalid page data!!
[ 7.639955@0] all discard block full!!
[ 7.643550@0] free block cnt = 1238
[ 7.646604@0] new current block is 1548
[ 7.901729@0] prio_garbage_collect_no_last_page_in_create_list put_phy_block_to_free_list!
[ 8.221883@0] recover_current_block_mapping : fill the current block, from page 255
[ 8.223900@0] total discard page count is 0
[ 8.228062@0] create_part_list:1238,current_used_discard_block=1225,current_discard_block_used_count=325
[ 8.242594@0] unmappig_pages=303701,discarded_pages=0,mapping_pages=55979
[ 8.244274@0] nftl ok!
[ 8.247335@0] Enable QUEUE_FLAG_DISCARD for NFTL
[ 8.251806@[ 8.258750@0] android_usb: already disabled
[ 8.258941@0] init: property 'ro.serialno' doesn't exist while expanding '${ro.serialno}'
[ 8.265531@0] init: cannot expand '${ro.serialno}' while writing to '/sys/class/android_usb/android0/iSerial'
[ 8.275410@0] init: Unable to open persistent pro[ 8.285540@3] cur_mode = 0
[ 8.285569@3] [0x0] = 0x1dd0190
[ 8.285736@3] [0x4] = 0xf800ca
[ 8.285911@1] systemcontrol: [ubootenv] open devices error: No such file or directory
[ 8.285919@1] systemcontrol: [ubootenv] Cannot read : -1.
[ 8.285926@1] systemcontrol: [ubootenv] open devices error: No such file or directory
[ 8.285931@1] systemcontrol: [ubootenv] Cannot read : -1.
[ 8.285936@1] systemcontrol: [ubootenv] open devices error: No such file or directory
[ 8.285944@1] systemcontrol: [ubootenv] Cannot read : -1.
[ 8.285951@1] systemcontrol: [ubootenv] open devices error: No such file or directory
[ 8.285956@1] systemcontrol: [ubootenv] Cannot read : -1.
[ 8.285961@1] systemcontrol: [ubootenv] open devices error: No such file or directory
[ 8.285966@1] systemcontrol: [ubootenv] Cannot read : -1.
[ 8.285970@1] systemcontrol: [ubootenv] read failed
[ 8.286295@1] systemcontrol: [ubootenv] ubootenv.var.hdmimode is not a ubootenv varible.
[ 8.286314@2] aml_nftl_open ok!
[ 8.286326@1] systemcontrol: [ubootenv] ubootenv.var.is.bestmode is not a ubootenv varible.
[ 8.286335@1] systemcontrol: [ubootenv] bootenv do not init
[ 8.286341@1] systemcontrol: [ubootenv] bootenv do not init
[ 8.286767@1] systemcontrol: [ubootenv] ubootenv.var.1080p_x is not a ubootenv varible.
[ 8.286775@1] systemcontrol: [ubootenv] ubootenv.var.1080p_y is not a ubootenv varible.
[ 8.286780@1] systemcontrol: [ubootenv] ubootenv.var.1080p_w is not a ubootenv varible.
[ 8.286785@1] systemcontrol: [ubootenv] ubootenv.var.1080p_h is not a ubootenv varible.
[ 8.286805@1] tvmode set to 1080p
[ 8.286813@1] don't set the same mode as current.
[ 8.287104@2] force enable DISCARD here for ext4 fs
[ 8.297933@2] checked enable EXT4 DISCARD here
[ 8.297938@2] EXT4-fs (cache): mounted filesystem with ordered data mode. Opts:
[ 8.298832@2] systemcontrol: [ubootenv] open devices error: No such file or directory
[ 8.298838@2] systemcontrol: [ubootenv] Cannot read : -1.
[ 8.298844@2] systemcontrol: [ubootenv] open devices error: No such file or directory
[ 8.298848@2] systemcontrol: [ubootenv] Cannot read : -1.
[ 8.298853@2] systemcontrol: [ubootenv] open devices error: No such file or directory
[ 8.298858@2] systemcontrol: [ubootenv] Cannot read : -1.
[ 8.298863@2] systemcontrol: [ubootenv] open devices error: No such file or directory
[ 8.298867@2] systemcontrol: [ubootenv] Cannot read : -1.
[ 8.298872@2] systemcontrol: [ubootenv] open devices error: No such file or directory
[ 8.298876@2] systemcontrol: [ubootenv] Cannot read : -1.
[ 8.298880@2] systemcontrol: [ubootenv] read failed
# [ 8.517742@3] [0x8] = 0x82006e
[ 8.517743@3] [0xc] = 0x3c0030
[ 8.517745@3] [0x10] = 0x30fa0013
[ 8.517746@3] [0x18] = 0x6f19000
[ 8.517747@3] [0x1c] = 0x9f40
[ 8.517748@3] [0x20] = 0x0
[ 8.517749@3] [0x24] = 0x0
[ 8.517749@3] [0x28] = 0x0
[ 8.517751@3] set_remote_mode[69]
[ 8.578893@1] systemcontrol: [ubootenv] ubootenv.var.digitaudiooutput is not a ubootenv varible.
[ 8.582061@1] buf=0
[ 8.584110@1] IEC958_mode_raw=0
[ 8.587241@1] systemcontrol: [ubootenv] ubootenv.var.1080p_x is not a ubootenv varible.
[ 8.595225@1] systemcontrol: [ubootenv] ubootenv.var.1080p_y is not a ubootenv varible.
[ 8.603192@1] systemcontrol: [ubootenv] ubootenv.var.1080p_w is not a ubootenv varible.
[ 8.611164@1] systemcontrol: [ubootenv] ubootenv.var.1080p_h is not a ubootenv varible.
[ 8.619182@1] osd0=>x:0 ,y:0,w:1920,h:1080
[ 8.619182@1] osd1=> x:0,y:0,w:18,h:18
[ 8.628940@1] osd[1] set scale, h_scale: ENABLE, v_scale: ENABLE
[ 8.633008@1] osd[1].scaledata: 1920 1920 1080 1080
[ 8.637853@1] osd[1].pandata: 0 0 0 0
[ 10.100194@2] systemcontrol: [ubootenv] open devices error: No such file or directory
[ 10.102385@2] systemcontrol: [ubootenv] Cannot read : -1.
[ 10.107757@2] systemcontrol: [ubootenv] open devices error: No such file or directory
[ 10.115583@2] systemcontrol: [ubootenv] Cannot read : -1.
[ 10.120950@2] systemcontrol: [ubootenv] open devices error: No such file or directory
[ 10.128733@2] systemcontrol: [ubootenv] Cannot read : -1.
[ 10.134121@2] systemcontrol: [ubootenv] open devices error: No such file or directory
[ 10.141915@2] systemcontrol: [ubootenv] Cannot read : -1.
[ 10.147284@2] systemcontrol: [ubootenv] open devices error: No such file or directory
[ 10.155090@2] systemcontrol: [ubootenv] Cannot read : -1.
[ 10.160463@2] systemcontrol: [ubootenv] read failed
[ 10.165510@2] systemcontrol: [ubootenv] open devices error: No such file or directory
[ 10.173295@2] systemcontrol: [ubootenv] Cannot read : -1.
[ 10.178663@2] systemcontrol: [ubootenv] open devices error: No such file or directory
[ 10.186472@2] systemcontrol: [ubootenv] Cannot read : -1.
[ 10.191847@2] systemcontrol: [ubootenv] open devices error: No such file or directory
[ 10.199639@2] systemcontrol: [ubootenv] Cannot read : -1.
[ 10.205022@2] systemcontrol: [ubootenv] open devices error: No such file or directory
[ 10.215868@2] systemcontrol: [ubootenv] Cannot read : -1.
[ 10.218190@2] systemcontrol: [ubootenv] open devices error: No such file or directory
[ 10.226004@2] systemcontrol: [ubootenv] Cannot read : -1.
[ 10.231371@2] systemcontrol: [ubootenv] read failed
[ 20.103103@0] remote_send_key
[ 20.103146@0] press ircode = 0x0e, scancode = 0x006c, maptable = 0
[ 20.106682@0] remote_send_key sleep:0
[ 20.459934@0] remote_send_key
[ 20.459964@0] release ircode = 0x0e, scancode = 0x006c, maptable = 0
[ 20.463691@0] remote_send_key sleep:0
[ 21.176171@0] remote_send_key
[ 21.176202@0] press ircode = 0x0e, scancode = 0x006c, maptable = 0
[ 21.179762@0] remote_send_key sleep:0
[ 21.504692@0] remote_send_key
[ 21.504720@0] release ircode = 0x0e, scancode = 0x006c, maptable = 0
[ 21.508442@0] remote_send_key sleep:0
[ 21.512092@0] remote_send_key
[ 21.515050@0] press ircode = 0x0e, scancode = 0x006c, maptable = 0
[ 21.521282@0] remote_send_key sleep:0
[ 21.797187@0] remote_send_key
[ 21.797219@0] release ircode = 0x0e, scancode = 0x006c, maptable = 0
[ 21.800951@0] remote_send_key sleep:0
[ 21.804579@0] remote_send_key
[ 21.807536@0] press ircode = 0x0e, scancode = 0x006c, maptable = 0
[ 21.813784@0] remote_send_key sleep:0
[ 22.073834@0] remote_send_key
[ 22.073865@0] release ircode = 0x0e, scancode = 0x006c, maptable = 0
[ 22.077584@0] remote_send_key sleep:0
[ 22.081246@0] remote_send_key
[ 22.084188@0] press ircode = 0x0e, scancode = 0x006c, maptable = 0
[ 22.090424@0] remote_send_key sleep:0
[ 22.313829@0] remote_send_key
[ 22.313860@0] release ircode = 0x0e, scancode = 0x006c, maptable = 0
[ 22.317580@0] remote_send_key sleep:0
[ 22.321231@0] remote_send_key
[ 22.324177@0] press ircode = 0x0e, scancode = 0x006c, maptable = 0
[ 22.330420@0] remote_send_key sleep:0
[ 22.575528@0] remote_send_key
[ 22.575559@0] release ircode = 0x0e, scancode = 0x006c, maptable = 0
[ 22.579286@0] remote_send_key sleep:0
[ 22.582930@0] remote_send_key
[ 22.585876@0] press ircode = 0x0e, scancode = 0x006c, maptable = 0
[ 22.592112@0] remote_send_key sleep:0
[ 22.825788@0] remote_send_key
[ 22.825818@0] release ircode = 0x0e, scancode = 0x006c, maptable = 0
[ 22.829549@0] remote_send_key sleep:0
[ 22.833189@0] remote_send_key
[ 22.836127@0] press ircode = 0x0e, scancode = 0x006c, maptable = 0
[ 22.842377@0] remote_send_key sleep:0
[ 23.125359@0] remote_send_key
[ 23.125389@0] release ircode = 0x0e, scancode = 0x006c, maptable = 0
[ 23.129123@0] remote_send_key sleep:0
[ 23.132751@0] remote_send_key
[ 23.135706@0] press ircode = 0x0e, scancode = 0x006c, maptable = 0
[ 23.141947@0] remote_send_key sleep:0
[ 23.489933@0] remote_send_key
[ 23.489974@0] release ircode = 0x0e, scancode = 0x006c, maptable = 0
[ 23.493683@0] remote_send_key sleep:0
[ 24.395789@0] remote_send_key
[ 24.395821@0] press ircode = 0x0d, scancode = 0x0061, maptable = 0
[ 24.399366@0] remote_send_key sleep:0
[ 24.759933@0] remote_send_key
[ 24.759963@0] release ircode = 0x0d, scancode = 0x0061, maptable = 0
[ 24.763689@0] remote_send_key sleep:0
[ 24.812498@0] SysRq : Emergency Remount R/O
[ 24.812645@0] aml_keys_notify_reboot:1717[ 24.815561@2] Emergency Remount complete
[ 24.816248@1] aml_nftl_open ok!
[ 24.825301@1] force enable DISCARD here for ext4 fs
[ 24.825386@0] sd 0:0:0:0: Driver sd calling sd_shutdown shutdown
[ 24.825641@0] rn5t618_pmu rn5t618_pmu.0: Driver rn5t618_pmu calling platform_drv_shutdown shutdown
[ 24.825651@0] ricoh_pmu 0-0032: Bus i2c calling i2c_device_shutdown shutdown
[ 24.825664@0] i2c i2c-3: Bus i2c calling i2c_device_shutdown shutdown
[ 24.825669@0] i2c i2c-2: Bus i2c calling i2c_device_shutdown shutdown
[ 24.825673@0] i2c i2c-1: Bus i2c calling i2c_device_shutdown shutdown
[ 24.825677@0] i2c i2c-0: Bus i2c calling i2c_device_shutdown shutdown
[ 24.825719@0] amlnfdev nand: Driver amlnfdev calling platform_drv_shutdown shutdown
[ 24.825723@0] boot_device_flag : 0
[ 24.825793@0] aml_rtc rtc.0: Driver aml_rtc calling platform_drv_shutdown shutdown
[ 24.826448@0] Restarting system with command 'android'.
[ 24.898070@0]
[ 24.899891@0] Restarting Linux version 3.10.33-gfa4a182-dirty (user@DroidBOX) (gcc version 4.8.2 (Ubuntu/Linaro 4.8.2-16ubuntu4) ) #2 SMP PREEMPT Fri Jan 15 09:37:53 CET 2016
[ 24.899891@0]
[ †!UÒššŠ²Âj
BT : 12:14:11 Jan 11 2016
PMU:rn5t618
DC01 v:1100, 0x[36]: 2c -> 28
DC02 v:1150, 0x[37]: 2c -> 2c
DC03 v:1500, 0x[38]: 48 -> 48
LDO01 v:2900, 0x[4c]: 50 -> 50
LDO02 v:1800, 0x[4d]: 24 -> 24
LDO03 v:1800, 0x[4e]: 30 -> 30
LDO04 v:2850, 0x[4f]: 4e -> 4e
LDO05 v:1800, 0x[50]: 24 -> 24
LDO0a v:2700, 0x[56]: 28 -> 28
LDO0b v:900, 0x[57]: 00 -> 00
CPU clock is 1200MHz
CPU type: M8
DDR info: 2GB(auto) @ 792MHz(1T)
DDR channel: DDR 0 + DDR 1
DDR init use : 12112 us
HHH
Boot From SPI
ucl decompress...pass
0x12345678
Boot from internal device 1st SPI
TE : 407205
System Started
U-boot-00000-g99c5e8c-dirty(m8_k200_v1@m201) (Jan 11 2016 - 12:14:01)
clr h-ram
DRAM: 2 GiB
relocation Offset is: 6feb0000
show partition table:
part: 0, name : logo, size : 2000000
part: 1, name : recovery, size : 2000000
part: 2, name : misc, size : 2000000
part: 3, name : boot, size : 2000000
part: 4, name : system, size : 40000000
part: 5, name : cache, size : 20000000
part: 6, name : data, size : end
aml_card_type=0x200
MMC: [mmc_register] add mmc dev_num=0, port=1, if_type=6
[mmc_register] add mmc dev_num=1, port=2, if_type=6
SDIO Port B: 0, SDIO Port C: 1
PMU fault status:
reg[0x9A] = 0x0d
LSI version:03, OTP version:06
PMU type:RN5T618
register usb cfg[0][1] = 7ff68328
register usb cfg[2][0] = 7ff6be54
mcli -- wifi_power_init in uboot --
enter spi boot
SF: Detected MX25L1605D with page size 256, total 2 MiB
SPI NOR Flash have write protect!!!
spi success
get_storage_device_flag: store 4
boot_device_flag 0
Nand PHY driver Version: 2.01.001.0004 (c) 2013 Amlogic Inc.
amlnf_phy_init : amlnf init flag 5
NAND device id: 2c 64 44 4b a9 0 0 0
detect NAND device: B revision NAND 8GiB MT29F64G08CBABA
nand chip ce mask 1
device_boot_flag=4
boot_device_flag 0
Nand PHY driver Version: 2.01.001.0004 (c) 2013 Amlogic Inc.
amlnf_phy_init : amlnf init flag 0
NAND device id: 2c 64 44 4b a9 0 0 0
detect NAND device: B revision NAND 8GiB MT29F64G08CBABA
nand chip ce mask 1
AML_NAND_NEW_OOB : new oob
bus_cycle=6, bus_timing=8,system=3.9ns,flash->T_REA =16,flash->T_RHOH=15
NAND CKECK : arg nbbt: arg_valid= 1, valid_blk_addr = 9, valid_page_addr = 0
nand block at blk 4 is bad
nand block at blk 5 is bad
nand block at blk 6 is bad
nand block at blk 7 is bad
NAND CKECK : arg ncnf: arg_valid= 1, valid_blk_addr = 10, valid_page_addr = 0
nand block at blk 4 is bad
nand block at blk 5 is bad
nand block at blk 6 is bad
nand block at blk 7 is bad
NAND CKECK : arg nkey: arg_valid= 1, valid_blk_addr = 8, valid_page_addr = 43
i=0,register --- nand_key
nand block at blk 4 is bad
nand block at blk 5 is bad
nand block at blk 6 is bad
nand block at blk 7 is bad
NAND CKECK : arg phyp: arg_valid= 1, valid_blk_addr = 11, valid_page_addr = 1
nand blk 4 is shipped bad block
nand blk 5 is shipped bad block
nand blk 6 is shipped bad block
nand blk 7 is shipped bad block
amlnand_phydev_init,1171,phydev->offset=6800000,phydev->size=24800000
amlnand_phydev_init,1171,phydev->offset=2b000000,phydev->size=51800000
amlnand_phydev_init,1171,phydev->offset=7c800000,phydev->size=183800000
nfcache : offset: 0x000006800000 -0x000024800000 : partitons 1 : single_chip multi_plane
nfcode : offset: 0x00002b000000 -0x000051800000 : partitons 5 : single_chip multi_plane
nfdata : offset: 0x00007c800000 -0x000183800000 : partitons 1 : single_chip multi_plane
amlnf_logic_init: START
amlnf_logic_init: COMPLETE
SPI BOOT,spi_env_relocate_spec : env_relocate_spec 64
spi env have been init already, just retun here
set_storage_device_flag: store 4
Multi dtb tool version: v2 .
Multi dtb detected, support 6 dtbs.
aml_dt soc: m8 platform: k200 variant: 2gsdhc
dtb 0 soc: m8 plat: k200 vari: 2gsdhc
dtb 1 soc: m8 plat: k200 vari: 2gsdio
dtb 2 soc: m8 plat: k200 vari: sdhc
dtb 3 soc: m8 plat: k200 vari: sdio
dtb 4 soc: m8m2 plat: n200 vari: 1G
dtb 5 soc: m8m2 plat: n200 vari: 2G
Find match dtb: 0
vpu driver detect cpu type: m8
vpu clk_level in dts: 7
set vpu clk: 364300000Hz, readback: 364300000Hz(0x700)
Net: Meson_Ethernet
init suspend firmware done. (ret:0)
cvbs trimming.1.v5: 0xa0, 0x0
android
SPI BOOT,spi_saveenv : saveenv 122
Erasing SPI flash...Writing to SPI flash...done
wipe_data=successful
wipe_cache=successful
reboot_mode=android
TV mode 1080p selected.
mode = 8 vic = 16
set HDMI vic: 16
config HPLL
config HPLL done
reconfig packet setting done
Hit Enter key to stop autoboot -- : 1 0
exit abortboot: 0
current storer:nand_key
key save is auto select storer(nand or emmc)
write key code version3_flush:709,prov->write:7fed99f4
write key ok!!
Booting...
pos 509 value is 20ERR(v2_common/optimus_download_key.c)L473:failed to query key state, rc 0, keyIsBurned=0
pos 509 value is 20ERR(v2_common/optimus_download_key.c)L473:failed to query key state, rc 0, keyIsBurned=0
bootprio= boot
## ANDROID Format IMAGE
## Booting kernel from Legacy Image at 12000000 ...
Image Name: Linux-3.10.33
Image Type: ARM Linux Kernel Image (lzo compressed)
Data Size: 6708859 Bytes = 6.4 MiB
Load Address: 00208000
Entry Point: 00208000
Verifying Checksum ... OK
Ramdisk start addr = 0x12666800, len = 0x1138bb
Multi dtb tool version: v2 .
Multi dtb detected, support 6 dtbs.
aml_dt soc: m8 platform: k200 variant: 2gsdhc
dtb 0 soc: m8 plat: k200 vari: 2gsdhc
dtb 1 soc: m8 plat: k200 vari: 2gsdio
dtb 2 soc: m8 plat: k200 vari: sdhc
dtb 3 soc: m8 plat: k200 vari: sdio
dtb 4 soc: m8m2 plat: n200 vari: 1G
dtb 5 soc: m8m2 plat: n200 vari: 2G
Find match dtb: 0
Flat device tree start addr = 0x1277b000, len = 0x516a magic=0xedfe0dd0
Uncompressing Kernel Image ... OK
uboot time: 3199079 us.
EFUSE machid is not set.
Using machid 0xf81 from environment
From device tree /memory/ node aml_reserved_end property, for relocate ramdisk and fdt, relocate_addr: 0x511d001
Loading Ramdisk to 05009000, end 0511c8bb ... OK
Loading Device Tree to 05000000, end 05008169 ... OK
Starting kernel ...
[ 0.000000@0] Booting Linux on physical CPU 0x200
[ 0.000000@0] Initializing cgroup subsys cpu
[ 0.000000@0] Initializing cgroup subsys cpuacct
[ 0.000000@0] Linux version 3.10.33-gfa4a182-dirty (user@DroidBOX) (gcc version 4.8.2 (Ubuntu/Linaro 4.8.2-16ubuntu4) ) #2 SMP PREEMPT Fri Jan 15 09:37:53 CET 2016
[ 0.000000@0] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c5387d
[ 0.000000@0] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000@0] Machine: Amlogic Meson8, model: AMLOGIC
[ 0.000000@0] physical memory start address is 0x200000
[ 0.000000@0] reserved_end is 1d9fffff
[ 0.000000@0]
[ 0.000000@0] Total memory is 2046 MiB
[ 0.000000@0] Reserved low memory from 0x06000000 to 0x1d9fffff, size: 378 MiB
[ 0.000000@0] mesonfb0(low) : 0x06100000 - 0x07900000 ( 24 MiB)
[ 0.000000@0] mesonfb1(low) : 0x07900000 - 0x07a00000 ( 1 MiB)
[ 0.000000@0] deinterlace0(high) : 0x7df00000 - 0x80000000 ( 33 MiB)
[ 0.000000@0] mesonstream0(low) : 0x07a00000 - 0x09a00000 ( 32 MiB)
[ 0.000000@0] vdec0(low) : 0x09a00000 - 0x19a00000 (256 MiB)
[ 0.000000@0] ppmgr0(high) : 0x7bf00000 - 0x7df00000 ( 32 MiB)
[ 0.000000@0] vdin00(low) : 0x19a00000 - 0x1aa00000 ( 16 MiB)
[ 0.000000@0] vdin10(low) : 0x1aa00000 - 0x1ba00000 ( 16 MiB)
[ 0.000000@0] amlvideo20(low) : 0x1ba00000 - 0x1d200000 ( 24 MiB)
[ 0.000000@0] amvideocap0(low) : 0x1d200000 - 0x1da00000 ( 8 MiB)
[ 0.000000@0] get storage device: storage 4
[ 0.000000@0] value=4
[ 0.000000@0] get_storage_device : get storage device: storage 4
[ 0.000000@0] get_storage_device : value=4
[ 0.000000@0] [get_storage_device] storage_flag=4
[ 0.000000@0] [get_storage_device] the storage device does NOT relate to eMMC, storage_flag=4
[ 0.000000@0] cma: CMA: reserved 8 MiB at 2f000000
[ 0.000000@0] cma: Found region@0, memory base 0, size 18 MiB
[ 0.000000@0] cma: CMA: reserved 20 MiB at 2dc00000
[ 0.000000@0] Memory policy: ECC disabled, Data cache writealloc
[ 0.000000@0] Meson chip version = RevC (19:C - 0:27ED)
[ 0.000000@0] PERCPU: Embedded 9 pages/cpu @c1f09000 s13120 r8192 d15552 u36864
[ 0.000000@0] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 405264
[ 0.000000@0] Kernel command line: rootfstype=ramfs init=/init console=ttyS0,115200n8 no_console_suspend earlyprintk ramoops.mem_address=0x04e00000 ramoops.mem_size=0x100000 ramoops.record_size=0x8000 ramoops.console_size=0x4000 androidboot.selinux=permissive storage=4 cvbsdrv=0 vdaccfg=0xa000 logo=osd1,loaded,0x07900000,1080p,full hdmimode=1080p cvbsmode=576cvbs androidboot.firstboot=1 hdmitx= mac=00:01:db:88:00:0d
[ 0.000000@0] cvbs performance line = 0
[ 0.000000@0] cvbs trimming line = 0xa000
[ 0.000000@0] cvbs trimming.1.v5: 0xa0, 0x0
[ 0.000000@0] osd1:1
[ 0.000000@0] loaded:268435459
[ 0.000000@0] logo has been loaded
[ 0.000000@0] 1080p:15
[ 0.000000@0] full:2
[ 0.000000@0] kernel get hdmimode form uboot is 1080p
[ 0.000000@0] kernel get cvbsmode form uboot is 576cvbs
[ 0.000000@0] ******** uboot setup mac-addr: 0:1:db:88:0:d
[ 0.000000@0] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000@0] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000@0] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000@0] Memory: 64MB 16MB 1509MB = 1589MB total
[ 0.000000@0] Memory: 1564920k/1564920k available, 62216k reserved, 1250304K highmem
[ 0.000000@0] Virtual kernel memory layout:
[ 0.000000@0] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000@0] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000@0] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB)
[ 0.000000@0] lowmem : 0xc0000000 - 0xef800000 ( 760 MB)
[ 0.000000@0] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000@0] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000@0] .text : 0xc0008000 - 0xc0b83bc0 (11759 kB)
[ 0.000000@0] .init : 0xc0b84000 - 0xc0be3340 ( 381 kB)
[ 0.000000@0] .data : 0xc0be4000 - 0xc0c9d0e8 ( 741 kB)
[ 0.000000@0] .bss : 0xc0c9d0e8 - 0xc0f75f94 (2916 kB)
[ 0.000000@0] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000@0] Preemptible hierarchical RCU implementation.
[ 0.000000@0] NR_IRQS:256
[ 0.000000@0] sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 4294967ms
[ 0.000000@0] Switching to timer-based delay loop
[ 0.000000@0] console [ttyS0] enabled
[ 0.403550@0] Calibrating delay loop (skipped), value calculated using timer frequency.. 2.00 BogoMIPS (lpj=10000)
[ 0.413835@0] pid_max: default: 32768 minimum: 301
[ 0.418718@0] Security Framework initialized
[ 0.422878@0] SELinux: Disabled at boot.
[ 0.426903@0] Mount-cache hash table entries: 512
[ 0.434923@0] Initializing cgroup subsys debug
[ 0.435942@0] Initializing cgroup subsys freezer
[ 0.440614@0] CPU: Testing write buffer coherency: ok
[ 0.445868@0] CPU0: thread -1, cpu 0, socket 2, mpidr 80000200
[ 0.451434@0] Setting up static identity map for 0xc07f1970 - 0xc07f19c8
[ 0.458141@0] L310 cache controller enabled
[ 0.462238@0] l2x0: 8 ways, 4096 sets, CACHE_ID 0x4100a0c9, Cache size: 1048576 B
[ 0.469742@0] AUX_CTRL 0x7ec80001, PERFETCH_CTRL 0x71000007, POWER_CTRL 0x00000000
[ 0.477896@0] TAG_LATENCY 0x00000111, DATA_LATENCY 0x00000222
[ 0.560157@0] write pen_release: 1
[ 0.560363@1] CPU1: Booted secondary processor
[ 0.560375@1] CPU1: thread -1, cpu 1, socket 2, mpidr 80000201
[ 0.580153@0] write pen_release: 2
[ 0.588295@2] CPU2: Booted secondary processor
[ 0.588307@2] CPU2: thread -1, cpu 2, socket 2, mpidr 80000202
[ 0.600141@0] write pen_release: 3
[ 0.608283@3] CPU3: Booted secondary processor
[ 0.608295@3] CPU3: thread -1, cpu 3, socket 2, mpidr 80000203
[ 0.608361@0] Brought up 4 CPUs
[ 0.621493@0] SMP: Total of 4 processors activated (8.00 BogoMIPS).
[ 0.627722@0] CPU: All CPU(s) started in SVC mode.
[ 0.632979@0] devtmpfs: initialized
[ 0.640562@0] clkrate [ xtal ] : 24000000
[ 0.640590@0] clkrate [ pll_sys ] : 1200000000
[ 0.644539@0] clkrate [ pll_fixed ] : 2550000000
[ 0.649220@0] clkrate [ pll_vid ] : 366000000
[ 0.653648@0] TODO: clk_get_rate_hpll() is not implement in M8 now
[ 0.659794@0] clkrate [ pll_hpll ] : 0
[ 0.663614@0] clkrate [ pll_ddr ] : 0
[ 0.667337@0] clkrate [ a9_clk ] : 1200000000
[ 0.671764@0] clkrate [ clk81 ] : 141666666
[ 0.676737@0] pinctrl core: initialized pinctrl subsystem
[ 0.681558@0] regulator-dummy: no parameters
[ 0.686473@0] NET: Registered protocol family 16
[ 0.696101@0] DMA: preallocated 4096 KiB pool for atomic coherent allocations
[ 0.697687@0] ramoops: using module parameters
[ 0.702115@0] persistent_ram: found existing buffer, size 0, start 0
[ 0.708347@0] persistent_ram: found existing buffer, size 0, start 0
[ 0.714684@0] persistent_ram: found existing buffer, size 0, start 0
[ 0.721008@0] persistent_ram: found existing buffer, size 0, start 0
[ 0.727330@0] persistent_ram: found existing buffer, size 0, start 0
[ 0.733663@0] persistent_ram: found existing buffer, size 0, start 0
[ 0.739985@0] persistent_ram: found existing buffer, size 0, start 0
[ 0.746319@0] persistent_ram: found existing buffer, size 0, start 0
[ 0.752649@0] persistent_ram: found existing buffer, size 0, start 0
[ 0.758968@0] persistent_ram: found existing buffer, size 0, start 0
[ 0.765307@0] persistent_ram: found existing buffer, size 0, start 0
[ 0.771630@0] persistent_ram: found existing buffer, size 0, start 0
[ 0.777952@0] persistent_ram: found existing buffer, size 0, start 0
[ 0.784285@0] persistent_ram: found existing buffer, size 0, start 0
[ 0.790613@0] persistent_ram: found existing buffer, size 0, start 0
[ 0.796935@0] persistent_ram: found existing buffer, size 0, start 0
[ 0.803269@0] persistent_ram: found existing buffer, size 0, start 0
[ 0.809591@0] persistent_ram: found existing buffer, size 0, start 0
[ 0.815924@0] persistent_ram: found existing buffer, size 0, start 0
[ 0.822252@0] persistent_ram: found existing buffer, size 0, start 0
[ 0.828575@0] persistent_ram: found existing buffer, size 0, start 0
[ 0.834908@0] persistent_ram: found existing buffer, size 0, start 0
[ 0.841235@0] persistent_ram: found existing buffer, size 0, start 0
[ 0.847558@0] persistent_ram: found existing buffer, size 0, start 0
[ 0.853891@0] persistent_ram: found existing buffer, size 0, start 0
[ 0.860219@0] persistent_ram: found existing buffer, size 0, start 0
[ 0.866545@0] persistent_ram: found existing buffer, size 0, start 0
[ 0.872875@0] persistent_ram: found existing buffer, size 0, start 0
[ 0.879197@0] persistent_ram: found existing buffer, size 0, start 0
[ 0.885531@0] persistent_ram: found existing buffer, size 0, start 0
[ 0.891858@0] persistent_ram: found existing buffer, size 0, start 0
[ 0.898178@0] pstore przs=0xf0010000
[ 0.901741@0] persistent_ram: found existing buffer, size 832, start 832
[ 0.908484@0] pstore cprz=0xf0008000
[ 0.911969@0] persistent_ram: found existing buffer, size 0, start 0
[ 0.918744@0] console [pstore-1] enabled
[ 0.922196@0] cprz old_log=0xed748000
[ 0.925839@0] ramoops: attached 0x100000@0x4e00000, ecc: 0/0
[ 0.932362@0] VPU driver version: v03
[ 0.935107@0] vpu driver detect cpu type: m8
[ 0.939355@0] load vpu_clk in dts: 364300000Hz(7)
[ 0.944054@0] vpu_probe OK
[ 0.946957@0] cma: Assigned CMA region with name cma_0 to amvenc_avc.0 device
[ 0.955727@0] amlogic_gpio gpio: Probed amlogic GPIO driver
[ 0.959520@0] register lm device lm-root
[ 0.963322@0] register lm device lm1
[ 0.966859@0] register lm device lm0
[ 0.970515@0] Init pinux probe!
[ 0.973888@0] pinmux-m8 pinmux: Probed amlogic pinctrl driver
[ 0.979243@0] tv_init_module
[ 0.982102@0] major number 254 for disp
[ 0.985902@0] vout_register_server
[ 0.989282@0] register tv module server ok
[ 0.993381@0] major number 0 for disp
[ 0.996997@0] register tv module server ok
[ 1.001090@0] video2_early_init enter
[ 1.004712@0] video2_early_init exit
[ 1.008287@0] aml_i2c version: 20140813
[ 1.012215@0] aml-i2c i2c-AO: add adapter aml_i2c_adap0(ed73d0a8)
[ 1.018150@0] aml-i2c i2c-AO: aml i2c bus driver.
[ 1.022931@0] aml-i2c i2c-A: add adapter aml_i2c_adap1(ed73d4a8)
[ 1.028811@0] aml-i2c i2c-A: aml i2c bus driver.
[ 1.033522@0] aml-i2c i2c-B: add adapter aml_i2c_adap2(ed73d8a8)
[ 1.039387@0] aml-i2c i2c-B: aml i2c bus driver.
[ 1.044075@0] aml-i2c i2c-C: add adapter aml_i2c_adap3(ed73dca8)
[ 1.049962@0] aml-i2c i2c-C: aml i2c bus driver.
[ 1.054618@0] aml_pmu_init, 458
[ 1.057691@0] call aml_dvfs_init in
[ 1.061311@0] hdmitx: system: amhdmitx_init
[ 1.065303@0] hdmitx: system: Ver: 2014May6
[ 1.069518@0] hdmitx: system: amhdmitx_probe
[ 1.073854@0] hdmitx: system: not find cec config
[ 1.078391@0] hdmitx: system: not find vend_init_data
[ 1.083518@0] hdmitx: system: gate/pwr cmd: 7
[ 1.087755@0] hdmitx: system: ALREADY init VIC = 16
[ 1.092615@0] hdmitx: system: gate/pwr cmd: 0
[ 1.097331@1] hdmitx: system: reset intr mask
[ 1.120400@0] hdmitx: system: irq 1
[ 1.127195@0] bio: create slab <bio-0> at 0
[ 1.127602@0] SCSI subsystem initialized
[ 1.129750@0] usbcore: registered new interface driver usbfs
[ 1.135315@0] usbcore: registered new interface driver hub
[ 1.140794@0] usbcore: registered new device driver usb
[ 1.146006@0] Linux video capture interface: v2.00
[ 1.150738@0] pps_core: LinuxPPS API ver. 1 registered
[ 1.155817@0] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <[email protected]>
[ 1.165107@0] PTP clock support registered
[ 1.169400@0] mode is 15,sync_duration_den=1,sync_duration_num=60
[ 1.175247@0] TV mode 1080p selected.
[ 1.178875@0] already display in uboot
[ 1.182608@0] vinfo mode is: 1080p
[ 1.187952@0] call aml_pmu_probe_init in
[ 1.189928@0] aml_pmus_probe, child name:rn5t618
[ 1.194490@0] aml_pmus_probe, i2c_bus:i2c_bus_ao
[ 1.199347@0] board_has_battery:false
[ 1.203189@0] Allocate new i2c device: adapter:0, addr:0x32, node name:rn5t618, type:ricoh_pmu
[ 1.211501@0] Advanced Linux Sound Architecture Driver Initialized.
[ 1.217817@0] Bluetooth: Core ver 2.16
[ 1.221300@0] NET: Registered protocol family 31
[ 1.225857@0] Bluetooth: HCI device and connection manager initialized
[ 1.232370@0] Bluetooth: HCI socket layer initialized
[ 1.237391@0] Bluetooth: L2CAP socket layer initialized
[ 1.240769@1] hdmitx: system: gate/pwr cmd: 4
[ 1.246938@0] Bluetooth: SCO socket layer initialized
[ 1.252099@0] cfg80211: Calling CRDA to update world regulatory domain
[ 1.259562@0] Switching to clocksource Timer-E
[ 1.274565@0] NET: Registered protocol family 2
[ 1.274945@0] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[ 1.280698@0] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 1.287311@0] TCP: Hash tables configured (established 4096 bind 4096)
[ 1.293786@0] TCP: reno registered
[ 1.297129@0] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 1.303129@0] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 1.309667@0] NET: Registered protocol family 1
[ 1.314120@0] wifi_dev_probe
[ 1.316890@0] wifi_dt : interrupt_pin=GPIOX_21
[ 1.321316@0] wifi_dt : irq_num=null
[ 1.324874@0] wifi_dt : irq_trigger_type=GPIO_IRQ_HIGH
[ 1.329977@0] wifi_dt : power_on_pin=GPIOAO_6
[ 1.334320@0] wifi_dt : power_on_pin2=GPIOX_11
[ 1.338738@0] interrupt_pin=133, irq_num=4, irq_trigger_type=0, power_on_pin=6,clock_32k_pin=122
[ 1.347688@0] Unpacking initramfs...
[ 1.396562@0] Freeing initrd memory: 1100K (c4e09000 - c4f1c000)
[ 1.398078@0] audit: initializing netlink socket (disabled)
[ 1.402512@0] type=2000 audit(1.280:1): initialized
[ 1.407824@0] bounce pool size: 64 pages
[ 1.414160@0] VFS: Disk quotas dquot_6.5.2
[ 1.415462@0] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.423177@0] exFAT: Core Version 1.2.4
[ 1.425800@0] exFAT: FS Version 1.2.4
[ 1.430120@0] NTFS driver 2.1.30 [Flags: R/O].
[ 1.434056@0] fuse init (API version 7.22)
[ 1.438273@0] msgmni has been set to 672
[ 1.442530@0] NET: Registered protocol family 38
[ 1.443237@1] hdmitx: system: gate/pwr cmd: 5
[ 1.443239@1] hdmitx: edid: edid ready
[ 1.443241@1] hdmitx: system: gate/pwr cmd: 4
[ 1.458952@0] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
[ 1.466379@0] io scheduler noop registered
[ 1.470443@0] io scheduler deadline registered
[ 1.474950@0] io scheduler cfq registered (default)
[ 1.482142@0] loop: module loaded
[ 1.483400@0] tun: Universal TUN/TAP device driver, 1.6
[ 1.488215@0] tun: (C) 1999-2004 Max Krasnyansky <[email protected]>
[ 1.494671@0] PPP generic driver version 2.4.2
[ 1.499045@0] PPP BSD Compression module registered
[ 1.503827@0] PPP Deflate Compression module registered
[ 1.509019@0] PPP MPPE Compression module registered
[ 1.513964@0] NET: Registered protocol family 24
[ 1.518602@0] usbcore: registered new interface driver asix
[ 1.524173@0] usbcore: registered new interface driver ax88179_178a
[ 1.530371@0] usbcore: registered new interface driver cdc_ether
[ 1.536354@0] usbcore: registered new interface driver dm9601
[ 1.542060@0] usbcore: registered new interface driver net1080
[ 1.547882@0] usbcore: registered new interface driver cdc_subset
[ 1.553948@0] usbcore: registered new interface driver zaurus
[ 1.559677@0] usbcore: registered new interface driver cdc_ncm
[ 1.565476@0] usbcore: registered new interface driver qf9700
[ 1.571196@0] usbcore: registered new interface driver sr9600
[ 1.577038@0] usbcore: registered new interface driver cdc_acm
[ 1.582693@0] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 1.590891@0] usbcore: registered new interface driver usb-storage
[ 1.597073@0] usbcore: registered new interface driver usbserial
[ 1.603012@0] usbcore: registered new interface driver option
[ 1.608715@0] usbserial: USB Serial support registered for GSM modem (1-port)
[ 1.615999@0] mousedev: PS/2 mouse device common for all mice
[ 1.621729@0] usbcore: registered new interface driver xpad
[ 1.627115@0] usbcore: registered new interface driver usb_acecad
[ 1.633177@0] usbcore: registered new interface driver aiptek
[ 1.638890@0] usbcore: registered new interface driver gtco
[ 1.643229@1] hdmitx: system: gate/pwr cmd: 5
[ 1.643230@1] hdmitx: edid: edid ready
[ 1.643235@1] hdmitx: edid: check sum valid
[ 1.643236@1] hdmitx: edid: check sum valid
[ 1.643238@1] hdmitx: edid: blk0 raw data
[ 1.643261@1] 00ffffffffffff0014e101000000000011170103800002781acf74a3574cb023
[ 1.643283@1] 09484c00000081c0d1c0010101010101010101010101023a801871382d40582c
[ 1.643304@1] 4500c48e2100001e00000018001c1620582c2500c48e2100009e000000fc0045
[ 1.643326@1] 6c6761746f0a202020202020000000fd00173d19460f000a20202020202001e5
[ 1.643326@1]
[ 1.643328@1] hdmitx: edid: blk1 raw data
[ 1.643349@1] 020326f451850403021213941607061115a1a2271f1023090701830100006703
[ 1.643371@1] 0c002000202d8c0aa01451f01600267c4300c48e210000988c0ad08a20e02d10
[ 1.643392@1] 103e9600c48e21000019011d007251d01e206e285500c48e2100001f011d8018
[ 1.643413@1] 711c1620582c2500c48e2100009e0000000000000000000000000000000000ff
[ 1.643414@1]
[ 1.643443@1] hdmitx: edid: find IEEEOUT
[ 1.643486@1] hdmitx: video: get current mode: 1080p
[ 1.643494@1] is_similar_hdmi_vic[326] vic_old=16,mode_new=15
[ 1.643497@1] hdmitx: system: [set_disp_mode_auto] ALREADY init VIC = 16
[ 1.643500@1] hdmitx: audio: audio channel num is 0
[ 1.643505@1] hdmitx: audio: SPDIF
[ 1.643516@1] hdmitx: audio: current VIC: 16
[ 1.643518@1] hdmitx: audio: audio sample rate: 0
[ 1.643519@1] hdmitx: audio: set audio N para
[ 1.643527@1] hdmitx: audio: PCM out to HDMI
[ 1.664073@1] hdmitx: audio: Time out: AIU_HDMI_CLK_DATA_CTRL
[ 1.664075@1] hdmitx: audio: i2s_to_spdif_flag:1
[ 1.664077@1] hdmitx: audio: Enable audio spdif to HDMI
[ 1.664131@1] hdmitx: cec: CEC not ready
[ 1.664134@1] hdmi detect: plug.
[ 1.799367@0] usbcore: registered new interface driver hanwang
[ 1.805166@0] usbcore: registered new interface driver kbtab
[ 1.810777@0] usbcore: registered new interface driver wacom
[ 1.816474@0] i2c /dev entries driver
[ 1.820360@0] usbcore: registered new interface driver uvcvideo
[ 1.825936@0] USB Video Class driver (1.1.1)
[ 1.830340@0] device-mapper: uevent: version 1.0.3
[ 1.835116@0] device-mapper: ioctl: 4.24.0-ioctl (2013-01-15) initialised: [email protected]
[ 1.843674@0] Bluetooth: HCI UART driver ver 2.2
[ 1.848115@0] Bluetooth: HCI H4 protocol initialized
[ 1.853264@0] hidraw: raw HID events driver (C) Jiri Kosina
[ 1.859953@0] usbcore: registered new interface driver usbhid
[ 1.864337@0] usbhid: USB HID core driver
[ 1.868619@0] zram: Created 1 device(s) ...
[ 1.872748@0] ashmem: initialized
[ 1.875888@0] logger: created 256K log 'log_main'
[ 1.880543@0] logger: created 256K log 'log_events'
[ 1.885416@0] logger: created 256K log 'log_radio'
[ 1.890169@0] logger: created 256K log 'log_system'
[ 1.895075@0] vout_init_module
[ 1.897999@0] start init vout module
[ 1.901531@0] create vout attribute ok
[ 1.905669@0] ge2d_init
[ 1.907755@0] ge2d_dev major:243
[ 1.911061@0] ge2d start monitor
[ 1.914225@0] osd_init
[ 1.914232@1] ge2d workqueue monitor start
[ 1.920614@0] osd_probe, vinfo:c084ccc0
[ 1.924580@0] Frame buffer memory assigned at phy:0x06100000, vir:0xf1000000, size=24576K
[ 1.932543@0] osd_probe, mydef_var:c0c36bf0, vinfo:c084ccc0
[ 1.938106@0] init fbdev bpp is :32
[ 1.941557@0] ---------------clear framebuffer0 memory
[ 1.968992@0] Frame buffer memory assigned at phy:0x07900000, vir:0xf0400000, size=1024K
[ 1.971437@0] osd_probe, mydef_var:c0c36bf0, vinfo:c084ccc0
[ 1.976996@0] don't find to display_size_default from mesonfb-dts
[ 1.983059@0] init fbdev bpp is :16
[ 2.002244@0] osd probe ok
[ 2.002346@0] osd_ext_init
[ 2.002566@0] vout2_init_module enter
[ 2.005684@0] start init vout2 module
[ 2.009307@0] create vout2 attribute ok
[ 2.013242@0] enter aml_sysled_init
[ 2.017017@0] amlvideo-000: V4L2 device registered as video10
[ 2.022512@0] amlvideo2: V4L2 device registered as video11
[ 2.027999@0] ionvideo-000: V4L2 device registered as video13
[ 2.033566@0] Video Technology Magazine Ion Video Capture Board ver 1.0 successfully loaded.
[ 2.042234@0] aml_wdt_driver_init,301
[ 2.045639@0] ** disable watchdog
[ 2.049023@0] keys===========================================
[ 2.054653@0] keys_devno=f000000
[ 2.057903@0] securitykey: device aml_keys created
[ 2.062598@0] amlkeys=0
[ 2.065069@0] platform_driver_register--aml_keys_driver--------------------
[ 2.072149@0] set uart_ao pinmux use pinctrl subsystem
[ 2.077098@0] P_AO_RTI_PIN_MUX_REG:78005861
[ 2.081251@0] start uart_ao_ttyS0:(irq = 122)
[ 2.085589@0] register uart_ao ok
[ 2.089000@0] set uart_a pinmux use pinctrl subsystem
[ 2.093912@0] P_AO_RTI_PIN_MUX_REG:78005861
[ 2.098056@0] start uart_a_ttyS1:(irq = 58)
[ 2.102206@0] register uart_a ok
[ 2.105567@0] start uart_d_ttyS4:(irq = 126)
[ 2.109661@0] register uart_d ok
[ 2.112977@0] dwc_otg: version 3.10a 12-MAY-2014
[ 2.117488@0] dwc_otg_driver_probe NOT match
[ 2.121742@0] usb1: type: 1, speed: 0, config: 0, dma: 0, id: 1, phy: fe108820, ctrl: fe080000
[ 2.130326@0] USB (1) use clock source: XTAL input
[ 2.156143@0] Core Release: 3.10a
[ 2.156175@0] Setting default values for core params
[ 2.158767@0] curmode: 1, host_only: 1
[ 2.182597@0] Using Buffer DMA mode
[ 2.182623@0] OTG VER PARAM: 1, OTG VER FLAG: 1
[ 2.184975@0] Working on port type = HOST
[ 2.189676@0] dwc_otg lm1: DWC OTG Controller
[ 2.193324@0] dwc_otg lm1: new USB bus registered, assigned bus number 1
[ 2.199967@0] dwc_otg lm1: irq 63, io mem 0x00000000
[ 2.204920@0] -------hcd->flags.d32 = 0
[ 2.208722@0] Init: Port Power? op_state=1
[ 2.212778@0] Init1: Power Port (0)
[ 2.216361@0] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.223214@0] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.230551@0] usb usb1: Product: DWC OTG Controller
[ 2.235426@0] usb usb1: Manufacturer: Linux 3.10.33 dwc_otg_hcd
[ 2.241303@0] usb usb1: SerialNumber: lm1
[ 2.245593@0] hub 1-0:1.0: USB hub found
[ 2.249193@0] hub 1-0:1.0: 1 port detected
[ 2.253471@0] usb0: type: 0, speed: 0, config: 0, dma: 0, id: 0, phy: fe108800, ctrl: fe040000
[ 2.261848@0] USB (0) use clock source: XTAL input
[ 2.287689@0] Core Release: 3.10a
[ 2.287716@0] Setting default values for core params
[ 2.290310@0] curmode: 1, host_only: 0
[ 2.354147@0] Using Buffer DMA mode
[ 2.354173@0] OTG VER PARAM: 1, OTG VER FLAG: 1
[ 2.356505@0] Working on port type = OTG
[ 2.360404@0] Current port type: SLAVE
[ 2.364278@0] dwc_otg lm0: DWC OTG Controller
[ 2.368479@0] dwc_otg lm0: new USB bus registered, assigned bus number 2
[ 2.375185@0] dwc_otg lm0: irq 62, io mem 0x00000000
[ 2.380114@0] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.387048@0] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.394407@0] usb usb2: Product: DWC OTG Controller
[ 2.399241@0] usb usb2: Manufacturer: Linux 3.10.33 dwc_otg_hcd
[ 2.405158@0] usb usb2: SerialNumber: lm0
[ 2.409373@0] hub 2-0:1.0: USB hub found
[ 2.413065@0] hub 2-0:1.0: 1 port detected
[ 2.417210@0] Dedicated Tx FIFOs mode
[ 2.420969@0] using timer detect id change, ed971800
[ 2.425806@0] boot_device_flag : 0
[ 2.429058@0] ===========================================amlnf_init:643,nand device tree ok,dev-name:nand
[ 2.438600@0] Nand PHY driver Version: 2.01.001.0006 (c) 2013 Amlogic Inc.
[ 2.445482@0] amlnf_phy_init : amlnf init flag 0
[ 2.450082@2] HOST mode
[ 2.450133@0] ######STS IRQ mode for nand driver
[ 2.450189@0] NAND device id: 2c 64 44 4b a9 0 0 0
[ 2.450194@0] detect NAND device: B revision NAND 8GiB MT29F64G08CBABA
[ 2.452959@1] Indeed it is in host mode hprt0 = 00021501
[ 2.468592@0] status:0
[ 2.468598@0] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.10.33-gfa4a182-dirty #2
[ 2.468621@0] [<c00148e8>] (unwind_backtrace+0x0/0xf4) from [<c0011984>] (show_stack+0x10/0x14)
[ 2.468631@0] [<c0011984>] (show_stack+0x10/0x14) from [<c04c6b20>] (controller_quene_rb+0x1c0/0x1d0)
[ 2.468640@0] [<c04c6b20>] (controller_quene_rb+0x1c0/0x1d0) from [<c04bd4f8>] (nand_reset+0xd0/0x1c4)
[ 2.468646@0] [<c04bd4f8>] (nand_reset+0xd0/0x1c4) from [<c04bd860>] (read_id+0x68/0x144)
[ 2.468652@0] [<c04bd860>] (read_id+0x68/0x144) from [<c04bcdf4>] (amlnand_chip_init+0x360/0x72c)
[ 2.468658@0] [<c04bcdf4>] (amlnand_chip_init+0x360/0x72c) from [<c04c5a0c>] (amlnf_phy_init+0x180/0x204)
[ 2.468668@0] [<c04c5a0c>] (amlnf_phy_init+0x180/0x204) from [<c04b729c>] (amlnf_init+0xd4/0x12c)
[ 2.468681@0] [<c04b729c>] (amlnf_init+0xd4/0x12c) from [<c02f6cf4>] (driver_probe_device+0xd0/0x214)
[ 2.468690@0] [<c02f6cf4>] (driver_probe_device+0xd0/0x214) from [<c02f6ee4>] (__driver_attach+0x68/0x8c)
[ 2.468697@0] [<c02f6ee4>] (__driver_attach+0x68/0x8c) from [<c02f5298>] (bus_for_each_dev+0x4c/0x98)
[ 2.468704@0] [<c02f5298>] (bus_for_each_dev+0x4c/0x98) from [<c02f640c>] (bus_add_driver+0xd0/0x258)
[ 2.468711@0] [<c02f640c>] (bus_add_driver+0xd0/0x258) from [<c02f74f4>] (driver_register+0xa8/0x13c)
[ 2.468719@0] [<c02f74f4>] (driver_register+0xa8/0x13c) from [<c0008564>] (do_one_initcall+0xa8/0x150)
[ 2.468731@0] [<c0008564>] (do_one_initcall+0xa8/0x150) from [<c0b84bdc>] (kernel_init_freeable+0x138/0x1e0)
[ 2.468740@0] [<c0b84bdc>] (kernel_init_freeable+0x138/0x1e0) from [<c07dee30>] (kernel_init+0x8/0x158)
[ 2.468749@0] [<c07dee30>] (kernel_init+0x8/0x158) from [<c000dcd8>] (ret_from_fork+0x14/0x3c)
[ 2.487871@0] status:0
[ 2.487875@0] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.10.33-gfa4a182-dirty #2
[ 2.487884@0] [<c00148e8>] (unwind_backtrace+0x0/0xf4) from [<c0011984>] (show_stack+0x10/0x14)
[ 2.487891@0] [<c0011984>] (show_stack+0x10/0x14) from [<c04c6b20>] (controller_quene_rb+0x1c0/0x1d0)
[ 2.487898@0] [<c04c6b20>] (controller_quene_rb+0x1c0/0x1d0) from [<c04bd4f8>] (nand_reset+0xd0/0x1c4)
[ 2.487904@0] [<c04bd4f8>] (nand_reset+0xd0/0x1c4) from [<c04bd860>] (read_id+0x68/0x144)
[ 2.487909@0] [<c04bd860>] (read_id+0x68/0x144) from [<c04bcdf4>] (amlnand_chip_init+0x360/0x72c)
[ 2.487915@0] [<c04bcdf4>] (amlnand_chip_init+0x360/0x72c) from [<c04c5a0c>] (amlnf_phy_init+0x180/0x204)
[ 2.487922@0] [<c04c5a0c>] (amlnf_phy_init+0x180/0x204) from [<c04b729c>] (amlnf_init+0xd4/0x12c)
[ 2.487931@0] [<c04b729c>] (amlnf_init+0xd4/0x12c) from [<c02f6cf4>] (driver_probe_device+0xd0/0x214)
[ 2.487938@0] [<c02f6cf4>] (driver_probe_device+0xd0/0x214) from [<c02f6ee4>] (__driver_attach+0x68/0x8c)
[ 2.487945@0] [<c02f6ee4>] (__driver_attach+0x68/0x8c) from [<c02f5298>] (bus_for_each_dev+0x4c/0x98)
[ 2.487951@0] [<c02f5298>] (bus_for_each_dev+0x4c/0x98) from [<c02f640c>] (bus_add_driver+0xd0/0x258)
[ 2.487958@0] [<c02f640c>] (bus_add_driver+0xd0/0x258) from [<c02f74f4>] (driver_register+0xa8/0x13c)
[ 2.487965@0] [<c02f74f4>] (driver_register+0xa8/0x13c) from [<c0008564>] (do_one_initcall+0xa8/0x150)
[ 2.487973@0] [<c0008564>] (do_one_initcall+0xa8/0x150) from [<c0b84bdc>] (kernel_init_freeable+0x138/0x1e0)
[ 2.487980@0] [<c0b84bdc>] (kernel_init_freeable+0x138/0x1e0) from [<c07dee30>] (kernel_init+0x8/0x158)
[ 2.487987@0] [<c07dee30>] (kernel_init+0x8/0x158) from [<c000dcd8>] (ret_from_fork+0x14/0x3c)
[ 2.507102@0] status:0
[ 2.507106@0] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.10.33-gfa4a182-dirty #2
[ 2.507114@0] [<c00148e8>] (unwind_backtrace+0x0/0xf4) from [<c0011984>] (show_stack+0x10/0x14)
[ 2.507121@0] [<c0011984>] (show_stack+0x10/0x14) from [<c04c6b20>] (controller_quene_rb+0x1c0/0x1d0)
[ 2.507128@0] [<c04c6b20>] (controller_quene_rb+0x1c0/0x1d0) from [<c04bd4f8>] (nand_reset+0xd0/0x1c4)
[ 2.507133@0] [<c04bd4f8>] (nand_reset+0xd0/0x1c4) from [<c04bd860>] (read_id+0x68/0x144)
[ 2.507139@0] [<c04bd860>] (read_id+0x68/0x144) from [<c04bcdf4>] (amlnand_chip_init+0x360/0x72c)
[ 2.507145@0] [<c04bcdf4>] (amlnand_chip_init+0x360/0x72c) from [<c04c5a0c>] (amlnf_phy_init+0x180/0x204)
[ 2.507152@0] [<c04c5a0c>] (amlnf_phy_init+0x180/0x204) from [<c04b729c>] (amlnf_init+0xd4/0x12c)
[ 2.507160@0] [<c04b729c>] (amlnf_init+0xd4/0x12c) from [<c02f6cf4>] (driver_probe_device+0xd0/0x214)
[ 2.507167@0] [<c02f6cf4>] (driver_probe_device+0xd0/0x214) from [<c02f6ee4>] (__driver_attach+0x68/0x8c)
[ 2.507174@0] [<c02f6ee4>] (__driver_attach+0x68/0x8c) from [<c02f5298>] (bus_for_each_dev+0x4c/0x98)
[ 2.507180@0] [<c02f5298>] (bus_for_each_dev+0x4c/0x98) from [<c02f640c>] (bus_add_driver+0xd0/0x258)
[ 2.507187@0] [<c02f640c>] (bus_add_driver+0xd0/0x258) from [<c02f74f4>] (driver_register+0xa8/0x13c)
[ 2.507194@0] [<c02f74f4>] (driver_register+0xa8/0x13c) from [<c0008564>] (do_one_initcall+0xa8/0x150)
[ 2.507202@0] [<c0008564>] (do_one_initcall+0xa8/0x150) from [<c0b84bdc>] (kernel_init_freeable+0x138/0x1e0)
[ 2.507209@0] [<c0b84bdc>] (kernel_init_freeable+0x138/0x1e0) from [<c07dee30>] (kernel_init+0x8/0x158)
[ 2.507216@0] [<c07dee30>] (kernel_init+0x8/0x158) from [<c000dcd8>] (ret_from_fork+0x14/0x3c)
[ 2.632936@1] usb 1-1: new high-speed USB device number 2 using dwc_otg
[ 2.633157@0] Indeed it is in host mode hprt0 = 00001101
[ 2.834102@0] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608
[ 2.834106@0] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 2.834110@0] usb 1-1: Product: USB2.0 Hub
[ 2.834552@0] hub 1-1:1.0: USB hub found
[ 2.834815@0] hub 1-1:1.0: 4 ports detected
[ 2.978735@0] AML_NAND_NEW_OOB : new oob
[ 2.982440@0] bus_cycle=6, bus_timing=8,system=3.9ns,flash->T_REA =16,flash->T_RHOH=15
[ 2.990358@0] boot_device_flag = 0
[ 2.996061@0] NAND CKECK : arg nbbt: arg_valid= 1, valid_blk_addr = 9, valid_page_addr = 0
[ 3.002924@2] -------hcd->flags.d32 = 0
[ 3.005106@0] nand block at blk 4 is bad
[ 3.005108@0] nand block at blk 5 is bad
[ 3.005110@0] nand block at blk 6 is bad
[ 3.005112@0] nand block at blk 7 is bad
[ 3.006380@0] NAND CKECK : arg ncnf: arg_valid= 1, valid_blk_addr = 10, valid_page_addr = 0
[ 3.006713@0] nand shipped bbt at block 0
[ 3.006715@0] nand block at blk 4 is bad
[ 3.006717@0] nand block at blk 5 is bad
[ 3.006718@0] nand block at blk 6 is bad
[ 3.006720@0] nand block at blk 7 is bad
[ 3.022152@0] NAND CKECK : arg phyp: arg_valid= 1, valid_blk_addr = 11, valid_page_addr = 1
[ 3.022558@0] nand block at blk 4 is bad
[ 3.022560@0] nand block at blk 5 is bad
[ 3.022562@0] nand block at blk 6 is bad
[ 3.022564@0] nand block at blk 7 is bad
[ 3.052760@0] NAND CKECK : arg nkey: arg_valid= 1, valid_blk_addr = 8, valid_page_addr = 45
[ 3.053128@0] i=0,register --- nand_key
[ 3.053139@0] nand blk 4 is shipped bad block
[ 3.053141@0] nand blk 5 is shipped bad block
[ 3.053143@0] nand blk 6 is shipped bad block
[ 3.053144@0] nand blk 7 is shipped bad block
[ 3.053164@0] amlnand_phydev_init,1177,phydev->offset=6800000,phydev->size=24800000
[ 3.053168@0] amlnand_phydev_init,1177,phydev->offset=2b000000,phydev->size=51800000
[ 3.053175@0] amlnand_phydev_init,1177,phydev->offset=7c800000,phydev->size=183800000
[ 3.053181@0] nfcache : offset: 0x000006800000 -0x000024800000 : partitons 1 : single_chip multi_plane
[ 3.053184@0] nfcode : offset: 0x00002b000000 -0x000051800000 : partitons 5 : single_chip multi_plane
[ 3.053187@0] nfdata : offset: 0x00007c800000 -0x000183800000 : partitons 1 : single_chip multi_plane
[ 3.053189@0] amlnand_add_nftl:
[ 3.053191@0] Creating 1 ntd partitions
[ 3.053195@0] block_num 146
[ 3.055985@0] ------init_ntd
[ 3.056185@0] ntd: Giving out device 0 to nfcache
[ 3.056187@0] Creating 5 ntd partitions
[ 3.056189@0] block_num 326
[ 3.062488@0] ntd: Giving out device 1 to nfcode
[ 3.062490@0] Creating 1 ntd partitions
[ 3.062492@0] block_num 1550
[ 3.091944@0] ntd: Giving out device 2 to nfdata
[ 3.092239@0] ethernet_driver probe!
[ 3.092243@0] Please config phy interface.
[ 3.092245@0] Please config savepowermode.
[ 3.092246@0] Please config reset_pin_enable.
[ 3.092248@0] Please config reset_delay.
[ 3.092249@0] Please config reset_pin.
[ 3.092252@0] ethernetinit(dbg[c0c3d7e4]=1)
[ 3.092272@0] ethernet base addr is fe0c0000
[ 3.092283@0] write mac add to:ed999ec8: 00 01 db 88 00 0d |......|
[ 3.094781@0] libphy: AMLMAC MII Bus: probed
[ 3.094786@0] eth0: PHY ID 02430c54 at 0 IRQ -1 (0:00) active
[ 3.095243@0] Amlogic A/V streaming port init
[ 3.095976@0] buffersize=262144,0,start=0
[ 3.095984@0] Subtitle stbuf alloced at 0xece40000, size = 262144
[ 3.095986@0] changed the (2) buffer size from 0 to 262144
[ 3.096122@0] init vdec memsource 9a00000->199fffff
[ 3.096219@0] [tsync_pcr_init]init success.
[ 3.096220@0] amvideocap_init_module
[ 3.096251@0] amvideocap_probe,amvideocap
[ 3.096255@0] amvideocap_dev_register buf:1d200000,size:800000.
[ 3.096428@0] regist mpeg12 codec profile
[ 3.096468@0] regist mpeg4 codec profile
[ 3.096470@0] amvdec_vc1 module init
[ 3.096509@0] regist vc1 codec profile
[ 3.096511@0] amvdec_h264 module init
[ 3.096575@0] regist h264 codec profile
[ 3.096576@0] amvdec_h264mvc module init
[ 3.096612@0] regist hmvc codec profile
[ 3.096613@0] amvdec_h264_4k2k module init
[ 3.096649@0] regist h264_4k2k codec profile
[ 3.096650@0] amvdec_h265 module init
[ 3.096689@0] regist hevc_unsupport codec profile
[ 3.096724@0] regist mjpeg codec profile
[ 3.096726@0] amvdec_real module init
[ 3.096760@0] amvdec_avs module init
[ 3.096852@0] amvenc_avc memory resource undefined.
[ 3.096854@0] encode_wq_init.
[ 3.096860@0] encode start monitor.
[ 3.096915@1] encode workqueue monitor start.
[ 3.097059@0] jpegenc module init
[ 3.097241@0] picdec buffer size is 4000000
[ 3.097355@0] alloc_keep_buffer keep_y_addr eca00000
[ 3.097369@0] alloc_keep_buffer keep_u_addr ecf00000
[ 3.097377@0] alloc_keep_buffer keep_v_addr ed000000
[ 3.097379@0] yaddr=eca00000,u_addr=ecf00000,v_addr=ed000000
[ 3.097581@0] create_ge2d_work_queue video task ok
[ 3.097583@0] video2_init enter
[ 3.097866@0] video2_drv_probe exit
[ 3.098134@0]
[ 3.098134@0]
[ 3.098134@0] VECM init
[ 3.098134@0]
[ 3.098282@0] efuse===========================================
[ 3.098369@0] efuse: device efuse created
[ 3.098411@0] efuse--------------------------------------------
[ 3.098412@0] SARADC Driver init.
[ 3.098498@0] __saradc_probe__
[ 3.113166@0] usb 1-1.3: new full-speed USB device number 3 using dwc_otg
[ 3.215998@0] usb 1-1.3: New USB device found, idVendor=046d, idProduct=c52b
[ 3.216003@0] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 3.216006@0] usb 1-1.3: Product: USB Receiver
[ 3.216009@0] usb 1-1.3: Manufacturer: Logitech
[ 3.243052@0] saradc calibration: ref_val = 507
[ 3.243054@0] saradc calibration: ref_nominal = 512
[ 3.243055@0] saradc calibration: coef = 4112
[ 3.243276@0] irblaster probe
[ 3.243397@0] Remote Driver
[ 3.243464@0] Remote platform_data g_remote_base=fe600580
[ 3.243491@0] set drvdata completed
[ 3.243499@0] device_create_file completed
[ 3.243821@0] input: aml_keypad as /devices/platform/meson-remote/input/input0
[ 3.243985@0] input_register_device completed
[ 3.244027@0] [0xffffff00] = 0x1dd0190
[ 3.244029@0] [0xffffff04] = 0xf800ca
[ 3.244030@0] [0xffffff08] = 0x82006e
[ 3.244032@0] [0xffffff0c] = 0x3c0030
[ 3.244033@0] [0xffffff10] = 0x30fa0013
[ 3.244035@0] [0xffffff18] = 0x6f19000
[ 3.244036@0] [0xffffff1c] = 0xbe40
[ 3.244038@0] [0x0] = 0xfa00a0
[ 3.244039@0] [0x4] = 0xfa00a0
[ 3.244040@0] [0x8] = 0xfa00a0
[ 3.244042@0] [0xc] = 0x640030
[ 3.244043@0] [0x10] = 0x30fa0013
[ 3.244045@0] [0x18] = 0x961b800
[ 3.244046@0] [0x1c] = 0x9740
[ 3.244047@0] [0x20] = 0x104
[ 3.244049@0] [0x24] = 0x0
[ 3.244050@0] [0x28] = 0x0
[ 3.244053@0] set_remote_mode[69]
[ 3.244073@0] remote config major:232
[ 3.244165@0] physical address:0x2d0ae000
[ 3.244195@0] ADC Keypad Driver init.
[ 3.244281@0] ==touch_ts_init==
[ 3.244357@0] ==ft5x0x_ts_init==
[ 3.244380@0] ==goodix_ts_init==
[ 3.244413@0] i2c-core: driver [gslx680_compatible] using legacy suspend method
[ 3.244415@0] i2c-core: driver [gslx680_compatible] using legacy resume method
[ 3.244439@0] !!!ntp_ts: ret = 0.
[ 3.244441@0] VTL ct36x TouchScreen driver, <[email protected]>.
[ 3.244457@0] i2c-core: driver [ct36x] using legacy suspend method
[ 3.244459@0] i2c-core: driver [ct36x] using legacy resume method
[ 3.244462@0] VTL ct36x TouchScreen driver End.
[ 3.244463@0] ==gsl_ts_init==
[ 3.244486@0] ret=0
[ 3.244538@0] ####################come here #####################
[ 3.260046@0] up vfd key(103) registed.
[ 3.260048@0] down vfd key(108) registed.
[ 3.260050@0] right vfd key(106) registed.
[ 3.260052@0] back vfd key(158) registed.
[ 3.260054@0] left vfd key(105) registed.
[ 3.260055@0] ok vfd key(232) registed.
[ 3.260173@0] input: vfd_keypad as /devices/platform/m1-vfd.0/input/input1
[ 3.260263@0] vfd config major:231
[ 3.260536@0] i2c-core: driver [mir3da] using legacy suspend method
[ 3.260538@0] i2c-core: driver [mir3da] using legacy resume method
[ 3.260557@0] i2c-core: driver [lis3dh_acc] using legacy suspend method
[ 3.260559@0] i2c-core: driver [lis3dh_acc] using legacy resume method
[ 3.260593@0] i2c-core: driver [bma222] using legacy suspend method
[ 3.260594@0] i2c-core: driver [bma222] using legacy resume method
[ 3.260633@0] i2c-core: driver [dmard06] using legacy suspend method
[ 3.260634@0] i2c-core: driver [dmard06] using legacy resume method
[ 3.260653@0] lsm303d driver: init
[ 3.260693@0] i2c-core: driver [dmard10] using legacy suspend method
[ 3.260695@0] i2c-core: driver [dmard10] using legacy resume method
[ 3.260715@0] stk8313_init
[ 3.260744@0] ======stk831x init ok======
[ 3.260746@0] stk831x_init
[ 3.260764@0] mxc622x accelerometer driver: init
[ 3.260778@0] i2c-core: driver [mxc622x] using legacy suspend method
[ 3.260780@0] i2c-core: driver [mxc622x] using legacy resume method
[ 3.260783@0] mxc6255xc accelerometer driver: init
[ 3.260798@0] i2c-core: driver [mxc6255xc] using legacy suspend method
[ 3.260799@0] i2c-core: driver [mxc6255xc] using legacy resume method
[ 3.260845@0] cm3217 v.1.0.0.1
[ 3.260865@0] i2c-core: driver [elan_epl6814] using legacy suspend method
[ 3.260867@0] i2c-core: driver [elan_epl6814] using legacy resume method
[ 3.260884@0] i2c-core: driver [LTR501] using legacy suspend method
[ 3.260886@0] i2c-core: driver [LTR501] using legacy resume method
[ 3.260938@0] GPIO Keypad Driver init.
[ 3.261002@0] ==gpio_key_probe==
[ 3.261021@0] reg:2620,clearmask=400040,setmask=1
[ 3.261024@0] reg:2622,clearmask=ff0000,set pin=3
[ 3.261027@0] reg:2623,clearmask=7000000,setmask=7
[ 3.261030@0] reg:2620,clearmask=800080,setmask=10001
[ 3.261032@0] reg:2622,clearmask=ff000000,set pin=3
[ 3.261035@0] reg:2623,clearmask=70000000,setmask=7
[ 3.261077@0] power key(116) registed.
[ 3.261177@0] input: gpio_keypad as /devices/platform/gpio_keypad.6/input/input2
[ 3.261259@0] gpio keypad register input device completed.
[ 3.261263@0] gpio keypad major:230
[ 3.261365@0] spi_nor_init
[ 3.261435@0] amlogic_spi_nor_probe:
[ 3.261444@0] amlogic_spi->state_name:default
[ 3.261515@0] AMLOGIC_SPI_NOR cc000000.spi: master is unqueued, this is deprecated
[ 3.261560@0] check_storage_device : spi boot_device_flag : 0
[ 3.261561@0] spi_nor_probe
[ 3.261589@0] spi_nor apollospi:32766: mx25l160 (2048 Kbytes)
[ 3.261754@0] Creating 2 MTD partitions on "apollospi:32766":
[ 3.261760@0] 0x000000000000-0x000000100000 : "bootloader"
[ 3.262288@0] 0x000000100000-0x000000110000 : "ubootenv"
[ 3.262738@0] amlogic_spi_nor_probe over
[ 3.262846@0] mmc driver version: 1.07, 2015-01-21: fix a bug in tuning which caused eMMC data CRC error
[ 3.927345@2] Init: Port Power? op_state=1
[ 3.931362@2] Init1: Power Port (0)
[ 3.932310@0] logitech-djreceiver 0003:046D:C52B.0003: hiddev0,hidraw0: USB HID v1.11 Device [Logitech USB Receiver] on usb-lm1-1.3/input2
[ 3.947238@2] [RN5T618]rÅ]
[ 4.152948@1]
[ 4.152948@1]
[ 4.152948@1]
[ 4.162213@1] [0;40;32m JTAG in[0m
[ 4.202941@1] reg:2620,clearmask=80008,setmask=10001
[ 4.202980@1] reg:2621,clearmask=ff000000,set pin=64
[ 4.207293@1] reg:2623,clearmask=7000,setmask=7
[ 4.211801@1] reg:2620,clearmask=200020,setmask=1
[ 4.216567@1] reg:2622,clearmask=ff00,set pin=64
[ 4.221161@1] reg:2623,clearmask=700000,setmask=7
[ 4.232966@2] pdata->caps 107
[ 4.232994@2] pdata->caps2 0
[ 4.233158@2] get property: port, value:0x00000000
[ 4.239659@2] get property: ocr_avail, value:0x00200000
[ 4.246174@2] get property: f_min, value:0x000493e0
[ 4.252661@2] get property: f_max, value:0x02faf080
[ 4.259171@2] get property: max_req_size, value:0x00020000
[ 4.265673@2] get property: pinname, str:sdio
[ 4.271471@2] get property: card_type, value:0x00000003
[ 4.302937@0] Indeed it is in host mode hprt0 = 00021501
[ 4.372915@2] [aml_sdio_probe] aml_sdio_probe() success!
[ 4.374045@2] host->base fe108e00
[ 4.375928@2] pdata->caps 80000547
[ 4.379260@2] pdata->caps2 0
[ 4.382121@2] get property: port, value:0x00000005
[ 4.388635@2] get property: ocr_avail, value:0x00200000
[ 4.395131@2] get property: f_min, value:0x000493e0
[ 4.401625@2] get property: f_max, value:0x05f5e100
[ 4.408133@2] get property: max_req_size, value:0x00020000
[ 4.414636@2] get property: pinname, str:emmc
[ 4.420435@2] get property: card_type, value:0x00000001
[ 4.426944@2] get property: gpio_dat3, str:BOOT_3
[ 4.432925@2] [is_emmc_exist] host->storage_flag=4, POR_BOOT_VALUE=5
[ 4.439245@2] [aml_sdhc_probe]: there is not eMMC/tsd, skip sdhc_c dts config!
[ 4.482938@0] usb 2-1: new high-speed USB device number 2 using dwc_otg
[ 4.484210@0] Indeed it is in host mode hprt0 = 00001101
[ 4.502915@2] [aml_sdhc_probe] aml_sdhc_probe() success!
[ 4.503010@2] [dsp]DSP start addr 0xc5e00000
[ 4.506853@2] [dsp]register dsp to char divece(257)
[ 4.511911@2] amlogic audio spdif interface device init!
[ 4.517043@2] name=nand_key nand_key
[ 4.520922@2] register_aes_algorithm:488,new way
[ 4.525608@2] key name:keyexample, key data:1234567890
[ 4.530827@2] aml_rtc rtc.0: rtc core: registered aml_rtc as rtc0
[ 4.537685@2] input: rn5t618_pmu as /devices/i2c-0/0-0032/rn5t618_pmu.0/input/input3
[ 4.544127@2] [RN5T618] NO BATTERY_PARAMETERS FOUND
[ 4.548873@2] [RN5T618]no battery, exit
[ 4.558722@2] vdin_drv_init: major 228
[ 4.558894@2] vdin0 mem_start = 0x19a00000, mem_size = 0x1000000
[ 4.562822@2] vdin_drv_probe: driver initialized ok
[ 4.567790@2] vdin1 mem_start = 0x1aa00000, mem_size = 0x1000000
[ 4.573665@2] vdin_drv_probe: driver initialized ok
[ 4.578573@2] amvdec_656in module: init.
[ 4.582405@2] amvdec_656in_init_module:major 227
[ 4.587227@2] amvdec_656in probe ok.
[ 4.590756@2] amvdec_csi probe ok.
[ 4.593971@2] [viuin..]viuin_init_module viuin module init
[ 4.599506@2] [viuin..]viuin_probe probe ok.
[ 4.603834@2] [isp..]isp_probe isp probe ok.
[ 4.607900@2] [sii9233a_drv_init] Ver: 2013Nov12
[ 4.613157@2] amaudio2: device amaudio2 created
[ 4.617113@2] Error: Didn't get power valid value --- wifi_power_probe 376
[ 4.623850@2] Error: Didn't get suspend_power_off value --- wifi_power_probe 393
[ 4.631206@2] wifi_power power_gpio is 6
[ 4.635115@2] wifi_power power_gpio2 is 123
[ 4.639403@2] amlogic rfkill init
[ 4.642609@2] not get gpio_en
[ 4.645518@2] not get gpio_wake
[ 4.672974@2] wifi_request_32k_clk : OFF-->ON for bt_rfkill
[ 4.673011@2] clock_32k_pin(122) : (null)
[ 4.676898@2] clock_32k_pin(122) : sdio_wifi
[ 4.684599@0] usb 2-1: New USB device found, idVendor=05e3, idProduct=0718
[ 4.688040@0] usb 2-1: New USB device strings: Mfr=0, Product=1, SerialNumber=2
[ 4.695320@0] usb 2-1: Product: USB Storage
[ 4.699454@0] usb 2-1: SerialNumber: 000000000033
[ 4.704649@0] usb-storage 2-1:1.0: USB Mass Storage device detected
[ 4.710648@0] scsi0 : usb-storage 2-1:1.0
[ 4.783985@2] aml_aes aml_aes: Aml AES
[ 4.784330@2] aml_tdes aml_tdes: Aml TDES
[ 4.786363@2] usbcore: registered new interface driver snd-usb-audio
[ 4.792640@2] enter rt5616_modinit
[ 4.795914@2] dummy_codec_platform_probe
[ 4.799802@2] == ES8323 == es8323_modinit()
[ 4.804286@2] i2s get no clk src setting in dts, use the default mpll 0
[ 4.810533@2] [aml-i2s-dai]enterd aml_i2s_dai_probe,old_samplerate:0,sample_rate=48000
[ 4.818572@2] [aml-spdif-dai]enter aml_dai_spdif_init
[ 4.823455@2] [aml-spdif-dai]enterd aml_spdif_play,set_clock:-1,sample_rate=4
[ 4.830551@2] audio_set_958_clk, freq=4,
[ 4.834465@2] IEC958 16bit
[ 4.837142@2] hdmitx: audio: aout notify rate 48000
[ 4.841994@2] hdmitx: audio: aout notify size 16
[ 4.846596@2] hdmitx: audio: aout notify format CT_PCM
[ 4.851704@2] hdmitx: audio: audio channel num is 1
[ 4.856567@2] hdmitx: audio: SPDIF
[ 4.859945@2] hdmitx: audio: current VIC: 16
[ 4.864192@2] hdmitx: audio: audio sample rate: 3
[ 4.868865@2] hdmitx: audio: set audio N para
[ 4.873211@2] hdmitx: audio: PCM out to HDMI
[ 4.877447@2] hdmitx: audio: i2s_to_spdif_flag:1
[ 4.882127@2] hdmitx: audio: Enable audio spdif to HDMI
[ 4.887338@2] hdmitx: audio: Audio Type: PCM
[ 4.891617@2] hdmitx: audio: set audio param
[ 4.895889@2] [aml-spdif-dai]aml_spdif_probe
[ 4.900167@2] test codec dummy_codec
[ 4.903636@2] using external codec, index = 1
[ 4.907959@2] using external dummy codec
[ 4.911939@2] enter spdif_dit_probe
[ 4.915421@2] aml_spdif_unmute
[ 4.918677@2] codec_name = dummy_codec.0
[ 4.922702@2] p_aml_audio->hp_disable=1
[ 4.926260@2] falied to get spk event delay time paraments from dts file
[ 4.932931@2] spk_event delay_time = 0
[ 4.937705@2] aml-i2s 0:playback preallocate_dma_buffer: area=ef300000, addr=2f500000, size=524288
[ 4.945922@2] aml-i2s 1:capture preallocate_dma_buffer: area=ef240000, addr=2f440000, size=65536
[ 4.954359@2] aml_snd_m8 aml_m8_sound_card.5: dummy_codec <-> aml-i2s-dai.0 mapping ok
[ 4.963596@2] aml-i2s 0:playback preallocate_dma_buffer: area=ef400000, addr=2f600000, size=524288
[ 4.971553@2] aml-i2s 1:capture preallocate_dma_buffer: area=ef260000, addr=2f460000, size=65536
[ 4.980018@2] aml_snd_m8 aml_m8_sound_card.5: dit-hifi <-> aml-spdif-dai.0 mapping ok
[ 4.988581@2] -----ext_codec=1---
[ 4.991187@2] =aml_m8_pinmux_init==,aml_m8_pinmux_init done,---0
[ 4.997278@2] GACT probability NOT on
[ 5.000801@2] Mirror/redirect action on
[ 5.004621@2] u32 classifier
[ 5.007470@2] Actions configured
[ 5.011027@2] Netfilter messages via NETLINK v0.30.
[ 5.015919@2] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 5.022492@2] ctnetlink v0.93: registering with nfnetlink.
[ 5.027642@2] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
[ 5.034697@2] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
[ 5.040950@2] xt_time: kernel timezone is -0000
[ 5.045270@2] ipip: IPv4 over IPv4 tunneling driver
[ 5.050410@2] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 5.055613@2] arp_tables: (C) 2002 David S. Miller
[ 5.060293@2] TCP: cubic registered
[ 5.063737@2] Initializing XFRM netlink socket
[ 5.068492@2] NET: Registered protocol family 10
[ 5.073267@2] mip6: Mobile IPv6
[ 5.075880@2] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 5.081560@2] sit: IPv6 over IPv4 tunneling driver
[ 5.086827@2] NET: Registered protocol family 17
[ 5.090790@2] NET: Registered protocol family 15
[ 5.095438@2] Bridge firewalling registered
[ 5.099618@2] Bluetooth: RFCOMM TTY layer initialized
[ 5.104585@2] Bluetooth: RFCOMM socket layer initialized
[ 5.109843@2] Bluetooth: RFCOMM ver 1.11
[ 5.113753@2] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 5.119204@2] Bluetooth: BNEP filters: protocol multicast
[ 5.124590@2] Bluetooth: BNEP socket layer initialized
[ 5.129693@2] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 5.135774@2] Bluetooth: HIDP socket layer initialized
[ 5.140888@2] l2tp_core: L2TP core driver, V2.0
[ 5.145398@2] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[ 5.150323@2] l2tp_ip: L2TP IP encapsulation support (L2TPv3)
[ 5.156067@2] l2tp_netlink: L2TP netlink interface
[ 5.160829@2] l2tp_eth: L2TP ethernet pseudowire support (L2TPv3)
[ 5.166899@2] l2tp_debugfs: L2TP debugfs support
[ 5.171473@2] l2tp_ip6: L2TP IP encapsulation support for IPv6 (L2TPv3)
[ 5.178101@2] NET: Registered protocol family 35
[ 5.183324@2] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[ 5.190470@2] Registering SWP/SWPB emulation handler
[ 5.195411@2] enter meson_pm_init
[ 5.198814@2] enter meson_pm_probe!
[ 5.202163@2] meson_pm_probe done !
[ 5.206143@2] file system registered
[ 5.209807@2] android_usb gadget: Mass Storage Function, version: 2009/09/11
[ 5.216219@2] android_usb gadget: Number of LUNs=2
[ 5.220971@2] lun0: LUN: removable file: (no medium)
[ 5.226006@2] lun1: LUN: removable file: (no medium)
[ 5.231182@2] android_usb gadget: android_usb ready
[ 5.236302@2] aml_rtc rtc.0: setting system clock to 1970-01-01 00:00:28 UTC (28)
[ 5.243364@2] ### dt-test ### No testcase data in device tree; not running tests
[ 5.250794@2] meson_cpufreq: no voltage_control prop
[ 5.255651@2] voltage_control = 0
[ 5.260094@2] <<-GTP-INFO->> GTP driver installing...
[ 5.264041@2] hdmitx: cec: CEC init
[ 5.267581@2] input: cec_input as /devices/virtual/input/input4
[ 5.273408@2] hdmitx: cec: hdmitx_device->cec_init_ready:0x1[ 5.278794@2] hdmitx: cec: CEC task process
[ 5.²[ 5.302918@2] Changing uart_ao_ttyS0: baud from 0 to 115200
[ 5.323058@2] Freeing unused kernel memory: 380K (c0b84000 - c0be3000)
[ 5.345558@3] init: aml-firstboot-init insert aml-firstboot-init
[ 5.346415@3] init: command 'loglevel 7' action=early-init status=0 (init.amlogic.board.rc:4)
[ 5.357238@3] aml_nftl_dev: module license 'Proprietary' taints kernel.
[ 5.361009@3] Disabling lock debugging due to kernel taint
[ 5.367260@3] boot_device_flag : 0
[ 5.369849@3] register_ntd_blktrans start
[ 5.373861@3] ntd device 250!
[ 5.376784@3] ntd->name: nfcache
[ 5.379993@3] adjust_block_num : 4,reserved_block_ratio 10
[ 5.385471@3] nftl version 150330d
[ 5.388832@3] nftl build Mar 30 2015_19:39:32
[ 5.393189@3] nftl part attr 0
[ 5.398354@3] nftl start:146,17, init flag 0
[ 5.400601@3] first
[ 5.451625@3] average_erase_count:0
[ 5.451651@3] second 7,129
[ 5.452163@3] part->max_discard_block = 4
[ 5.460059@3] current_block1:137
[ 5.490134@3] recover_current_block_mapping invalid page data!!
[ 5.491004@3] recover_current_block_mapping invalid page data!!
[ 5.496891@3] recover_current_block_mapping invalid page data!!
[ 5.502780@3] recover_current_block_mapping invalid page data!!
[ 5.508693@3] recover_current_block_mapping invalid page data!!
[ 5.514587@3] recover_current_block_mapping invalid page data!!
[ 5.520416@3] all discard block full!!
[ 5.523616@3] free block cnt = 139
[ 5.526990@3] new current block is 139
[ 5.704032@0] prio_garbage_collect_no_last_page_in_create_list put_phy_block_to_free_list!
[ 6.098035@0] recover_current_block_mapping : fill the current block, from page 255
[ 6.100052@0] total discard page count is 0
[ 6.104255@0] create_part_list:1238,current_used_discard_block=138,current_discard_block_used_count=11
[ 6.113917@0] unmappig_pages=31977,discarded_pages=0,mapping_pages=1047
[ 6.120097@0] nftl ok!
[ 6.122834@0] Enable QUEUE_FLAG_DISCARD for NFTL
[ 6.127717@0] aml_nftl_add_ntd ok
[ 6.130307@0] ntd device 250!
[ 6.133305@0] ntd->name: nfcode
[ 6.136391@0] adjust_block_num : 4,reserved_block_ratio 10
[ 6.141840@0] nftl version 150330d
[ 6.145239@0] nftl build Mar 30 2015_19:39:32
[ 6.149582@0] nftl part attr 0
[ 6.157502@0] size_in_blk 326; total_block 322;
[ 6.157527@0] nftl start:322,33, init flag 0
[ 6.161727@0] first
[ 6.265123@0] average_erase_count:0
[ 6.265146@0] second 244,289
[ 6.265834@0] part->max_discard_block = 4
[ 6.407723@0] all block full!!
[ 6.407743@0] all discard block full!!
[ 6.408929@0] free block cnt = 78
[ 6.412166@0] new current block is 77
[ 6.415833@0] total discard page count is 0
[ 6.419985@0] create_part_list:1238,current_used_discard_block=76,current_discard_block_used_count=249
[ 6.430120@0] unmappig_pages=13401,discarded_pages=0,mapping_pages=60583
[ 6.435967@0] nftl ok!
[ 6.438913@0] Enable QUEUE_FLAG_DISCARD for NFTL
[ 6.443491@0] Enable QUEUE_FLAG_DISCARD for NFTL
[ 6.447983@0] Enable QUEUE_FLAG_DISCARD for NFTL
[ 6.452593@0] Enable QUEUE_FLAG_DISCARD for NFTL
[ 6.457183@0] Enable QUEUE_FLAG_DISCARD for NFTL
[ 6.461693@0] aml_nftl_add_ntd ok
[ 6.464567@0] ntd device 250!
[ 6.467470@0] ntd->name: nfdata
[ 6.470611@0] adjust_block_num : 4,reserved_block_ratio 10
[ 6.476087@0] nftl version 150330d
[ 6.479432@0] nftl build Mar 30 2015_19:39:32
[ 6.483892@0] nftl part attr 0
[ 6.510030@0] nftl start:1550,145, init flag 0
[ 6.511293@0] first
[ 6.555978@2] [RN5T618]battery vol change: 0->0
[ 7.026108@0] average_erase_count:0
[ 7.026150@0] second 323,1405
[ 7.026907@0] part->max_discard_block = 4
[ 7.059018@0] scsi 0:0:0:0: Direct-Access USB TO I DE/SATA Device 0016 PQ: 0 ANSI: 4
[ 7.063364@1] sd 0:0:0:0: [sda] Test WP failed, assume Write Enabled
[ 7.068478@1] sd 0:0:0:0: [sda] Asking for cache data failed
[ 7.073610@1] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 7.082149@1] sd 0:0:0:0: [sda] Test WP failed, assume Write Enabled
[ 7.086690@1] sd 0:0:0:0: [sda] Asking for cache data failed
[ 7.091801@1] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 7.098052@1] sd 0:0:0:0: [sda] Attached SCSI disk
[ 7.227329@2] all block full!!
[ 7.227350@2] all discard block full!!
[ 7.228920@2] free block cnt = 1238
[ 7.231940@2] new current block is 1226
[ 7.235761@2] total discard page count is 0
[ 7.239916@2] create_part_list:1238,current_used_discard_block=1225,current_discard_block_used_count=326
[ 7.254204@2] unmappig_pages=303701,discarded_pages=0,mapping_pages=55979
[ 7.256125@2] nftl ok!
[ 7.259129@2] Enable QUEUE_FLAG_DISCARD for NFTL
[ 7.263598@2] aml_nftl_add_ntd ok
[ 7.266360@2] init_aml_nftl end
[ 7.269648@2] init: command 'insmod /boot/aml_nftl_dev.ko' action=early-init status=0 (init.amlogic.board.rc:9)
[ 7.284582@2] gpu cooling register okay with err=0
[ 7.284737@2] gpu core cooling register okay with err=0
[ 7.289644@2] Mali: Mali device driver loaded
[ 7.294034@2] init: command 'insmod /boot/mali.ko mali_debug_level=2 mali_shared_mem_size=0x40000000' action=early-init status=0 (init.amlogic.board.rc:10)
[ 7.307736@2] init: processing action 0xb646c970 (wait_for_coldboot_done)
[ 7.314475@2] init: wait for /dev/.coldboot_done
[ 7.319085@2] init: command 'wait_for_coldboot_done' action=wait_for_coldboot_done status=0 ((null):0)
[ 7.328351@2] init: processing action 0xb646c9a0 (mix_hwrng_into_linux_rng)
[ 7.335385@2] init: Mixed 512 bytes from /dev/hw_random into /dev/urandominit: command 'mix_hwrng_into_linux_rng' action=mix_hwrng_into_linux_rng status=0 ((null):0)
[ 7.350028@2] init: processing action 0xb646c9d0 (keychord_init)
[ 7.356004@2] init: command 'keychord_init' action=keychord_init status=0 ((null):0)
[ 0[ 7.369689@2] init: command 'console_init' action=console_init status=0 ((null):0)
[ 7.371618@2] init: processing action 0xb64460a0 (init)
[ 7.376832@2] init: command 'sysclktz 0' action=init status=0 (/init.rc:33)
[ 7.386674@2] init: property 'ro.serialno' doesn't exist while expanding '${ro.serialno}'
[ 7.391902@2] init: cannot expand '${ro.serialno}' while writing to '/sys/class/android_usb/android0/iSerial'
[ 7.401805@2] init: property 'ro.serialno' doesn't exist while expanding '${ro.serialno}'
[ 7.409941@2] init: cannot expand '${ro.serialno}' while writing to '/sys/class/android_usb/android0/iSerial'
[ 7.419819@2] init: enter do_confirm_formated /dev/block/data, /data
[ 7.426149@2] init: do_confirm_formated ext4 try mount
[ 7.431309@2] aml_nftl_open ok!
[ 7.435100@2] force enable DISCARD here for ext4 fs
[ 7.449286@2] checked enable EXT4 DISCARD here
[ 7.449316@2] EXT4-fs (data): mounted filesystem with ordered data mode. Opts: noauto_da_alloc
[ 7.458806@2] init: enter do_confirm_formated /dev/block/cache, /cache
[ 7.463255@2] init: do_confirm_formated ext4 try mount
[ 7.468342@2] aml_nftl_open ok!
[ 7.472073@2] force enable DISCARD here for ext4 fs
[ 7.485722@2] checked enable EXT4 DISCARD here
[ 7.485752@2] EXT4-fs (cache): mounted filesystem with ordered data mode. Opts: noauto_da_alloc
[ 7.496185@3] aml_nftl_open ok!
[ 7.497008@3] force enable DISCARD here for ext4 fs
[ 7.507416@3] checked enable EXT4 DISCARD here
[ 7.507447@3] EXT4-fs (system): mounted filesystem with ordered data mode. Opts: (null)
[ 7.514250@3] fs_mgr: __mount(source=/dev/block/system,target=/system,type=ext4)=0
[ 7.521761@3] blktrans_ioctl -cmd: 125d,801c0204,64
[ 7.526765@3] aml_nftl_open ok!
[ 7.530500@3] force enable DISCARD here for ext4 fs
[ 7.534669@3] EXT4-fs (data): Ignoring removed nomblk_io_submit option
[ 7.543261@3] checked enable EXT4 DISCARD here
[ 7.545578@3] EXT4-fs (data): mounted filesystem with ordered data mode. Opts: nomblk_io_submit,errors=remount-ro
[ 7.555838@3] fs_mgr: check_fs(): mount(/dev/block/data,/data,ext4)=0
[ 7.565651@3] fs_mgr: Running /system/bin/e2fsck on /dev/block/data
[ 7.641639@1] aml_nftl_open ok!
[ 7.641720@1] aml_nftl_open ok!
[ 7.651928@3] e2fsck: e2fsck 1.42.9 (28-Dec-2013)
[ 7.651988@3] e2fsck: /dev/block/data: clean, 1164/359744 files, 224910/1438720 blocks
[ 7.659077@3] aml_nftl_open ok!
[ 7.662701@3] force enable DISCARD here for ext4 fs
[ 7.666879@3] EXT4-fs (data): Ignoring removed nomblk_io_submit option
[ 7.677118@3] checked enable EXT4 DISCARD here
[ 7.677781@3] EXT4-fs (data): mounted filesystem with ordered data mode. Opts: nomblk_io_submit,errors=panic
[ 7.687613@3] fs_mgr: __mount(source=/dev/block/data,target=/data,type=ext4)=0
[ 7.694856@3] aml_nftl_open ok!
[ 7.698589@3] force enable DISCARD here for ext4 fs
[ 7.702749@3] EXT4-fs (cache): Ignoring removed nomblk_io_submit option
[ 7.711255@3] checked enable EXT4 DISCARD here
[ 7.713764@3] EXT4-fs (cache): mounted filesystem with ordered data mode. Opts: nomblk_io_submit,errors=remount-ro
[ 7.724095@3] fs_mgr: check_fs(): mount(/dev/block/cache,/cache,ext4)=0
[ 7.732793@3] fs_mgr: Running /system/bin/e2fsck on /dev/block/cache
[ 7.741506@1] aml_nftl_open ok!
[ 7.741581@1] aml_nftl_open ok!
[ 7.748995@3] e2fsck: e2fsck 1.42.9 (28-Dec-2013)
[ 7.749043@3] e2fsck: /dev/block/cache: clean, 21/32768 files, 4236/131072 blocks
[ 7.755691@3] aml_nftl_open ok!
[ 7.759334@3] force enable DISCARD here for ext4 fs
[ 7.763509@3] EXT4-fs (cache): Ignoring removed nomblk_io_submit option
[ 7.773639@3] checked enable EXT4 DISCARD here
[ 7.774502@3] EXT4-fs (cache): mounted filesystem with ordered data mode. Opts: nomblk_io_submit,errors=panic
[ 7.784424@3] fs_mgr: __mount(source=/dev/block/cache,target=/cache,type=ext4)=0
[ 7.835027@3] binder: 139:139 transaction failed 29189, size 0-0
[ 7.896110@2] buf[0]=75,buf[1]=9a,err=4
[ 7.896145@2] M8:adc=423,TS_C=5,flag=1
[ 7.898039@2] efuse_flag=a
[ 7.900729@2] amlogic_thermal_probe, this chip is trimmed, use thermal
[ 7.907262@2] amlogic-thermal aml_thermal: amlogic thermal probe start
[ 7.913751@2] #thermal-cells=7
[ 7.916764@2] keep_mode is disabled
[ 7.920231@2] pdata->temp_trip_count=4
[ 7.923977@2] temperature=70 on trip point=0
[ 7.928205@2] fixing high_freq=1608001 to 1608000 at trip point 0,level=2
[ 7.934987@2] fixing low_freq=1608001 to 1608000 at trip point 0,level=2
[ 7.941641@2] gpu[0].gpu_high_freq=511,tmp_level[0].gpu_high_freq=511
[ 7.948075@2] cpu[0] core num==3
[ 7.951261@2] gpu[0] core num==5
[ 7.954490@2] temperature=80 on trip point=1
[ 7.958719@2] fixing high_freq=1200001 to 1200000 at trip point 1,level=6
[ 7.965493@2] fixing low_freq=1200001 to 1200000 at trip point 1,level=6
[ 7.972154@2] gpu[1].gpu_high_freq=435,tmp_level[1].gpu_high_freq=435
[ 7.978588@2] cpu[1] core num==2
[ 7.981775@2] gpu[1] core num==4
[ 7.984999@2] temperature=90 on trip point=2
[ 7.989231@2] fixing high_freq=800001 to 696000 at trip point 2,level=11
[ 7.995903@2] fixing low_freq=800001 to 696000 at trip point 2,level=11
[ 8.002490@2] gpu[2].gpu_high_freq=328,tmp_level[2].gpu_high_freq=328
[ 8.008925@2] cpu[2] core num==2
[ 8.012115@2] gpu[2] core num==3
[ 8.015342@2] temperature=260 on trip point=3
[ 8.019653@2] fixing high_freq=-1 to -22 at trip point 3,level=-1
[ 8.025722@2] fixing low_freq=-1 to [ 8.028990@0] logd.auditd: start
-22 at trip point 3,level=-1
[ 8.034924@2] gpu[3].gpu_high_freq=-1,tmp_level[3].gpu_high_freq=-1
[ 8.041152@2] cpu[3] core num==-1
[ 8.044455@2] gpu[3] core num==-1
[ 8.047743@2] idle interval=1000
[ 8.050951@2] pdata->name:aml_thermal, pdata:ec3e0000
[ 8.056009@2] amlogic_thermal_init_from_dts, 998
[ 8.060573@2] amlogic_thermal_initialize, 1014, pdata:ec3e0000
[ 8.067041@2] tmp_trip[0].cpu_core_upper=1
[ 8.070468@2] tmp_trip[1].cpu_core_upper=2
[ 8.074568@2] tmp_trip[2].cpu_core_upper=2
[ 8.078611@2] tmp_trip[3].cpu_core_upper=-1
[ 8.082782@2] aml_thermal bind thermal-cpucore-0 okay !
[ 8.088041@2] aml_thermal bind thermal-cpufreq-0 okay !
[ 8.093189@2] tmp_trip[0].gpu_core_upper=1
[ 8.097248@2] tmp_trip[1].gpu_core_upper=2
[ 8.101322@2] tmp_trip[2].gpu_core_upper=3
[ 8.105417@2] tmp_trip[3].gpu_core_upper=-1
[ 8.109561@2] aml_thermal bind thermal-gpucore-0 okay !
[ 8.114790@2] pdata->tmp_trip[0].gpu_lower_level=1
[ 8.119517@2] pdata->tmp_trip[0].gpu_upper_level=1
[ 8.124326@2] pdata->tmp_trip[1].gpu_lower_level=2
[ 8.129051@2] pdata->tmp_trip[1].gpu_upper_level=2
[ 8.133847@2] pdata->tmp_trip[2].gpu_lower_level=3
[ 8.138583@2] pdata->tmp_trip[2].gpu_upper_level=3
[ 8.143380@2] pdata->tmp_trip[3].gpu_lower_level=-1
[ 8.148205@2] pdata->tmp_trip[3].gpu_upper_level=-1
[ 8.153083@2] aml_thermal bind thermal-gpufreq-0 okay !
[ 8.158389@2] amlogic: Kernel Thermal management registered
[ 8.163826@2] amlogic-thermal aml_thermal: amlogic thermal probe done
[ 8.171536@2] video first pts = 0
[ 8.173890@2] IEC958 16bit
[ 8.176208@2] hdmitx: audio: aout notify rate 48000
[ 8.181059@2] hdmitx: audio: aout notify size 16
[ 8.185665@2] hdmitx: audio: no update
[ 8.189380@2] aml_i2s_close device type 4
[ 8.193816@2] IEC958 16bit
[ 8.196145@2] hdmitx: audio: aout notify rate 48000
[ 8.201037@2] hdmitx: audio: aout notify size 16
[ 8.205614@2] hdmitx: audio: no update
[ 8.209325@2] aml_i2s_close device type 8
[ 8.214052@2] aml_i2s_close device type 1
[ 8.217214@3] read descriptors
[ 8.217219@3] read strings
[ 8.223452@2] IEC958 16bit
[ 8.225879@2] hdmitx: audio: aout notify rate 48000
[ 8.230734@2] hdmitx: audio: aout notify size 16
[ 8.235340@2] hdmitx: audio: no update
[ 8.239055@2] aml_i2s_close device type 2
root@T8S:/ # [ 8.246454@2] vfm_map_store:rm default
[ 8.248033@2] vfm_map_store:add default decoder ppmgr deinterlace amvideo
[ 8.254970@2] init: property 'ro.usb.vendor.string' doesn't exist while expanding '${ro.usb.vendor.string}'
[ 8.264480@2] init: cannot expand '${ro.usb.vendor.string}' while writing to '/sys/class/android_usb/android0/f_mass_storage/vendor_string'
[ 8.277119@2] init: property 'ro.usb.product.string' doesn't exist while expanding '${ro.usb.product.string}'
[ 8.286929@2] init: cannot expand '${ro.usb.product.string}' while writing to '/sys/class/android_usb/android0/f_mass_storage/product_string'
[ 8.301455@2] init: property 'ro.usb.vendor.string' doesn't exist while expanding '${ro.usb.vendor.string}'
[ 8.309211@2] init: cannot expand '${ro.usb.vendor.string}' while writing to '/sys/class/android_usb/android0/f_mass_storage/vendor_string'
[ 8.321704@2] init: property 'ro.usb.product.string' doesn't exist while expanding '${ro.usb.product.string}'
[ 8.331571@2] init: cannot expand '${ro.usb.product.string}' while writing to '/sys/class/android_usb/android0/f_mass_storage/product_string'
[ 8.345136@2] init: cannot find '/system/bin/debuggerd64', disabling 'debuggerd64'
[ 8.351775@2] init: cannot find '/system/bin/rild', disabling 'ril-daemon'
[ 8.359811@2] init: cannot find '/system/bin/install-recovery.sh', disabling 'flash_recovery'
[ 8.370722@2] android_usb: already disabled
[ 8.371439@2] mtp_bind_config
[ 8.374240@0] WARN::dwc_otg_handle_mode_mismatch_intr:167: Mode Mismatch Interrupt: currently in Host mode
[ 8.374240@0]
[ 8.385477@0] WARN::dwc_otg_handle_mode_mismatch_intr:167: Mode Mismatch Interrupt: currently in Host mode
[ 8.385477@0]
[ 8.396747@2] WARN::ep_dequeue:413: bogus device state
[ 8.396747@2]
[ 8.403701@2] mtp_bind_config
[ 8.406461@0] WARN::dwc_otg_handle_mode_mismatch_intr:167: Mode Mismatch Interrupt: currently in Host mode
[ 8.406461@0]
[ 8.423987@3] cur_mode = 0
[ 8.424019@3] [0x0] = 0x1dd0190
[ 8.424184@3] [0x4] = 0xf800ca
[ 8.427220@3] [0x8] = 0x82006e
[ 8.430256@3] [0xc] = 0x3c0030
[ 8.441263@3] [0x10] = 0x30fa0013
[ 8.441303@3] [0x18] = 0x6f19000
[ 8.441458@1] Adding 511996k swap on /dev/block/zram0. Priority:-1 extents:1 across:511996k SS
[ 8.441724@0] dig: data_integrity_guard main!
[ 8.455582@3] [0x1c] = 0x9f40
[ 8.458109@3] [0x20] = 0x0
[ 8.460794@3] [0x24] = 0x0
[ 8.463596@3] [0x28] = 0x0
[ 8.466170@3] set_remote_mode[69]
[ 8.481956@1] tvmode set to 1080p
[ 8.481993@1] don't set the same mode as current.
[ 8.535694@1] buf=0
[ 8.535715@1] IEC958_mode_raw=0
[ 8.535842@1] osd0=>x:0 ,y:0,w:1920,h:1080
[ 8.535842@1] osd1=> x:0,y:0,w:18,h:18
[ 8.549066@1] warning: `su' uses 32-bit capabilities (legacy support in use)
[ 8.553838@1] osd[1] set scale, h_scale: ENABLE, v_scale: ENABLE
[ 8.559669@1] osd[1].scaledata: 1920 1920 1080 1080
[ 8.564543@1] osd[1].pandata: 0 0 0 0
[ 8.569893@2] blktrans_ioctl -cmd: 125d,801c0204,64
[ 8.587075@2] EXT4-fs (system): re-mounted. Opts: (null)
[ 8.747323@0] EXT4-fs (system): re-mounted. Opts: (null)
[ 8.815563@1] EXT4-fs (system): re-mounted. Opts: (null)
[ 8.866712@3] init: untracked pid 277 exited with status 0
[ 10.586576@2] force enable DISCARD here for ext4 fs
[ 10.587136@2] checked enable EXT4 DISCARD here
[ 10.590250@2] EXT4-fs (zram0): mounting with "discard" option, but the device does not support discard
[ 10.599549@2] EXT4-fs (zram0): mounted filesystem with ordered data mode. Opts: (null)
[ 11.553471@1] CPU3: shutdown
[ 11.694067@1] CPU2: shutdown
[ 14.441499@1] vout [tv_set_vframe_rate_end_hint] return mode = 15, policy = 1!
[ 14.443122@1] vout [framerate_automation_set_mode] mode_target = 15
[ 14.449445@1] +++++++++++++++++framerate_automation_set_mode[1128]auto_mode=0++++++++++++++++
[ 15.066058@1] request_suspend_state: wakeup (3->0) at 14953148000 (1970-01-01 00:00:38.329760000 UTC)
[ 15.069644@1] request_suspend_state,169,old_sleep=0,new_state=0
[ 25.843103@1] write pen_release: 2
[ 26.143044@1] write pen_release: 3
[ 27.133290@2] IRQ94 no longer affine to CPU2
[ 27.133493@1] CPU2: shutdown
[ 27.173689@3] lowmemorykiller: lowmem_shrink: convert oom_adj to oom_score_adj:
[ 27.175361@3] lowmemorykiller: oom_adj 0 => oom_score_adj 0
[ 27.180905@3] lowmemorykiller: oom_adj 1 => oom_score_adj 58
[ 27.186555@3] lowmemorykiller: oom_adj 2 => oom_score_adj 117
[ 27.192261@3] lowmemorykiller: oom_adj 3 => oom_score_adj 176
[ 27.198033@3] lowmemorykiller: oom_adj 9 => oom_score_adj 529
[ 27.203734@3] lowmemorykiller: oom_adj 15 => oom_score_adj 1000
[ 27.273637@1] CPU3: shutdown
[ 27.943058@1] write pen_release: 2
[ 28.326592@1] acc_open
[ 28.326624@1] acc_release
[ 28.578879@0] netdev_open
[ 28.578904@0] Ethernet reset
[ 28.578923@0] NET MDA descpter start addr=ebd2b000
[ 28.584341@0] phy_interface = 1
[ 28.584367@0] aml_phy_init: trying to attach to 0:00
[ 28.584705@0] --1--write mac add to:ed999ec8: 00 01 db 88 00 0d |......|
[ 28.584718@0] unkown current key-name,key_read_show:1396
[ 28.584721@0] version NO error
[ 28.584722@0] ret = -22
[ 28.584722@0] print_buff=
[ 28.584731@0] --2--write mac add to:ed999ec8: 00 01 db 88 00 0d |......|
[ 28.584737@0] write mac add to:ed999ec8: 00 01 db 88 00 0d |......|
[ 28.584740@0] Current DMA mode=0, set mode=621c100
[ 28.584766@0] ether leave promiscuous mode
[ 28.584767@0] ether leave all muticast mode
[ 28.584769@0] changed the Multicast,mcount=1
[ 28.584772@0] add mac address:33:33:00:00:00:01,bit=1
[ 28.584773@0] set hash low=2,high=0
[ 28.584775@0] changed the filter setting to :4
[ 28.584782@0] changed the Multicast,mcount=1
[ 28.584818@0] add mac address:33:33:00:00:00:01,bit=1
[ 28.585393@0] changed the Multicast,mcount=2
[ 28.585397@0] add mac address:33:33:00:00:00:01,bit=1
[ 28.585400@0] add mac address:01:00:5e:00:00:01,bit=32
[ 28.585401@0] set hash low=2,high=1
[ 28.585403@0] changed the filter setting to :4
[ 28.585416@0] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 29.343063@1] write pen_release: 3
[ 29.343251@3] CPU3: Booted secondary processor
[ 29.395296@2] avc open
[ 29.428539@2] amvenc_avc check CMA pool sucess, max instance: 1.
[ 29.429529@2] amvenc_avc_open: allocating phys 2dc00000, size 18432k, wq:ea2f5a00.
[ 29.429533@2] amvenc_avc memory config sucess, buff start:0x2dc00000, size is 0x1200000, wq:ea2f5a00.
[ 29.429595@2] avc release, wq:ea2f5a00
[ 29.429599@2] remove encode_work_queue ea2f5a00 sucess, destroy_encode_work_queue line 2408.
[ 29.434984@2] ionvideo open
[ 29.434993@2] ionvideo_stop_generating!!!!
[ 29.435004@2] ionvideo release
[ 29.438023@1] ionvideo open
[ 29.438031@1] ionvideo_stop_generating!!!!
[ 29.438040@1] ionvideo release
[ 29.443499@1] ionvideo open
[ 29.443508@1] ionvideo_stop_generating!!!!
[ 29.443519@1] ionvideo release
[ 29.453670@1] ionvideo open
[ 29.453679@1] ionvideo_stop_generating!!!!
[ 29.453687@1] ionvideo release
[ 29.455231@1] ionvideo open
[ 29.455238@1] ionvideo_stop_generating!!!!
[ 29.455247@1] ionvideo release
[ 29.456713@1] ionvideo open
[ 29.456721@1] ionvideo_stop_generating!!!!
[ 29.456731@1] ionvideo release
[ 29.458499@1] ionvideo open
[ 29.458511@1] ionvideo_stop_generating!!!!
[ 29.458520@1] ionvideo release
[ 29.460283@1] ionvideo open
[ 29.460291@1] ionvideo_stop_generating!!!!
[ 29.460300@1] ionvideo release
[ 29.846345@3] Digital output mode: 0 - PCM
[ 29.851081@3] Digital output mode: 0 - PCM
[ 29.887995@3] Digital output mode: 0 - PCM
[ 30.460964@0] systemcontrol: [ubootenv] open devices error: No such file or directory
[ 30.463465@0] systemcontrol: [ubootenv] Cannot read : -1.
[ 30.470260@0] systemcontrol: [ubootenv] open devices error: No such file or directory
[ 30.476711@0] systemcontrol: [ubootenv] Cannot read : -1.
[ 30.482568@0] systemcontrol: [ubootenv] open devices error: No such file or directory
[ 30.490092@0] systemcontrol: [ubootenv] Cannot read : -1.
[ 30.495169@0] systemcontrol: [ubootenv] open devices error: No such file or directory
[ 30.503033@0] systemcontrol: [ubootenv] Cannot read : -1.
[ 30.508185@0] systemcontrol: [ubootenv] open devices error: No such file or directory
[ 30.516036@0] systemcontrol: [ubootenv] Cannot read : -1.
[ 30.521350@0] systemcontrol: [ubootenv] read failed
[ 30.521359@0] systemcontrol: [ubootenv] ubootenv.var.firstboot is not a ubootenv varible.
[ 31.452739@1] dig: data_integrity_guard isBootCompleted:1!
[ 31.453833@1] dig: dig set_data_ro_count count:0!
[ 32.091524@0] input: Logitech Unifying Device. Wireless PID:4024 as /devices/lm1/usb1/1-1/1-1.3/1-1.3:1.2/0003:046D:C52B.0003/input/input5
[ 32.100247@0] logitech-djdevice 0003:046D:C52B.0004: input,hidraw1: USB HID v1.11 Keyboard [Logitech Unifying Device. Wireless PID:4024] on usb-lm1-1.3:1
[ 32.114653@0] input: Logitech Unifying Device. Wireless PID:4024 as /devices/lm1/usb1/1-1/1-1.3/1-1.3:1.2/0003:046D:C52B.0003/input/input6
[ 32.126519@0] logitech-djdevice 0003:046D:C52B.0005: input,hidraw2: USB HID v1.11 Keyboard [Logitech Unifying Device. Wireless PID:4024] on usb-lm1-1.3:2
[ 35.152152@0] [aml-i2s-dai]i2s dma ef300000,phy addr 2f500000,mode 0,ch 2
[ 35.152155@0] ----aml_hw_iec958_init,runtime->rate=48000--
[ 35.152157@0] ----aml_hw_iec958_init,runtime->rate=48000,sample_rate=4--
[ 35.152160@0] iec958 mode PCM16
[ 35.152164@0] IEC958 16bit
[ 35.152170@0] hdmitx: audio: aout notify rate 48000
[ 35.152171@0] hdmitx: audio: aout notify size 16
[ 35.152172@0] hdmitx: audio: no update
[ 35.152174@0] [aml-spdif-dai]spdif dma ef300000,phy addr 2f500000
[ 35.152341@0] speaker_events--mute =1
[ 35.153429@0] [aml-i2s-dai]aiu i2s playback enable
[ 35.153429@0]
[ 35.153431@0] [aml-i2s-dai]audio_hw_958_enable 1
[ 36.752973@0] function[set_tm1628_led_value] line 228 display string: 00:01 .
[ 40.583265@2] IRQ94 no longer affine to CPU2
[ 40.583505@1] CPU2: shutdown
[ 40.733558@3] IRQ95 no longer affine to CPU3
[ 40.733880@1] CPU3: shutdown
[ 41.128503@0] BT_RADIO going: off
[ 41.128535@0] BCM_BT: going OFF
[ 41.153153@0] BT_RADIO going: on
[ 41.153189@0] BCM_BT: going ON
[ 41.232954@1] Changing uart_a_ttyS1: baud from 0 to 115200
[ 41.269126@0] EXT4-fs (sda): unable to read superblock
[ 41.272954@1] Changing uart_a_ttyS1: baud from 115200 to 2000000
[ 41.343141@1] write pen_release: 2
[ 41.792939@1] Changing uart_a_ttyS1: baud from 2000000 to 115200
[ 42.032960@1] Changing uart_a_ttyS1: baud from 115200 to 2000000
[ 42.916256@0] [aml-i2s-dai]aiu i2s playback disable
[ 42.916256@0]
[ 42.916258@0] [aml-i2s-dai]audio_hw_958_enable 0
[ 42.916269@0] IEC958 16bit
[ 42.916275@0] hdmitx: audio: aout notify rate 48000
[ 42.916277@0] hdmitx: audio: aout notify size 16
[ 42.916278@0] hdmitx: audio: no update
[ 42.916281@0] aml_i2s_close device type 8
[ 43.683331@2] IRQ94 no longer affine to CPU2
[ 43.683630@1] CPU2: shutdown
[ 43.846033@0] [aml-i2s-dai]i2s dma ef300000,phy addr 2f500000,mode 0,ch 2
[ 43.847315@0] ----aml_hw_iec958_init,runtime->rate=48000--
[ 43.852783@0] ----aml_hw_iec958_init,runtime->rate=48000,sample_rate=4--
[ 43.860122@0] iec958 mode PCM16
[ 43.862561@0] IEC958 16bit
[ 43.865378@0] hdmitx: audio: aout notify rate 48000
[ 43.870115@0] hdmitx: audio: aout notify size 16
[ 43.874791@0] hdmitx: audio: no update
[ 43.878441@0] [aml-spdif-dai]spdif dma ef300000,phy addr 2f500000
[ 43.885031@0] [aml-i2s-dai]aiu i2s playback enable
[ 43.885031@0]
[ 43.890871@0] [aml-i2s-dai]audio_hw_958_enable 1
[ 46.143135@1] write pen_release: 2
[ 47.111348@1] dhd_module_init: Enter
[ 47.111377@1] wifi_setup_dt
[ 47.112063@1] wifi_request_32k_clk : ON-->ON for sdio_wifi
[ 47.117611@1] interrupt_pin(133) : (null)
[ 47.121523@1] reg:2620,clearmask=100010,setmask=0
[ 47.126283@1] reg:2622,clearmask=ff,set pin=133
[ 47.130795@1] reg:2623,clearmask=70000,setmask=4
[ 47.135454@1] interrupt_pin(133) : sdio_wifi
[ 47.139638@1] power_on_pin(6) : (null)
[ 47.143411@1] power_on_pin(6) : sdio_wifi
[ 47.147350@1] power_on_pin2(123) : (null)
[ 47.151339@1] power_on_pin2(123) : sdio_wifi
[ 47.155640@1] WIFI Disable! 6
[ 47.371125@0] WIFI Enable! 6
[ 47.443166@1] write pen_release: 3
[ 48.572948@3] [aml_sdio_timeout][0;40;33m time_start_cnt:999
[0m[aml_sdio_print_err][0;40;33m sdio: Timeout error, Cmd52 arg 0xc00, Xfer 0 Bytes, host->xfer_step=12, host->cmd_is_stop=0, pdata->port=0, virqs=0x13, virqc=0x3f001f00, conf->cmd_clk_divide=177, pdata->clkc=177, conf->bus_width=0, pdata->width=0, conf=0x416270b1, clock=397940
[0m[aml_sdio_timeout][0;40;33m time_start_cnt:994
[0m[aml_sdio_print_err][0;40;33m sdio: Timeout error, Cmd52 arg 0x80000c08, Xfer 0 Bytes, host->xfer_step=12, host->cmd_is_stop=0, pdata->port=0, virqs=0x13, virqc=0x3f001f00, conf->cmd_clk_divide=177, pdata->clkc=177, conf->bus_width=0, pdata->width=0, conf=0x416270b1, clock=397940
[0m[aml_sdio_timeout][0;40;33m time_start_cnt:992
[0m[aml_sdio_print_err][0;40;33m sdio: Timeout error, Cmd8 arg 0x1aa, Xfer 0 Bytes, host->xfer_step=12, host->cmd_is_stop=0, pdata->port=0, virqs=0x13, virqc=0x1f001f00, conf->cmd_clk_divide=177, pdata->clkc=177, conf->bus_width=0, pdata->width=0, conf=0x416270b1, clock=397940
[ 50.613021@0] [0m[ 50.655414@1] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 50.656808@1] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 50.658451@1] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 50.661048@1] sdio: queuing unknown CIS tuple 0x80 (7 bytes)
[ 50.731036@1] sdio: queuing unknown CIS tuple 0x91 (3 bytes)
[ 50.731067@1] sdio: new high speed SDIO card at address 0001, clock 35416666, 4-bit-bus-width
[ 50.731612@0] [sdio_reinit] finish
[ 50.731815@0] =========== WLAN placed in POWER ON ========
[ 50.732167@1] bcmsdh_register: Linux Kernel SDIO/MMC Driver
[ 50.732438@1] dhd_customer_oob_irq_map: customer specific Host GPIO number is (100)
[ 50.735679@1] F1 signature OK, socitype:0x1 chip:0xa94c rev:0x2 pkg:0x0
[ 50.744706@1] DHD: dongle ram size is set to 524288(orig 524288) at 0x0
[ 50.758888@1] dhdsdio_probe: Disable prop_txstatus
[ 50.758934@1] dhd_conf_set_fw_name_by_chip: firmware_path=/etc/wifi/40183/fw_bcm43341b0_ag.bin
[ 50.761814@1] wl_create_event_handler(): thread:wl_event_handler:893 started
[ 50.761840@2] tsk Enter, tsk = 0xf6700444
[ 50.762706@1] dhd_attach(): thread:dhd_watchdog_thread:895 started
[ 50.762763@1] dhd_attach(): thread:dhd_dpc:896 started
[ 50.762809@1] dhd_attach(): thread:dhd_sysioc:897 started
[ 50.766810@1] Broadcom Dongle Host Driver: register interface [wlan0] MAC: 00:90:4c:11:22:33
[ 50.772889@1] =========== WLAN placed in RESET ========
[ 50.774222@1]
[ 50.774222@1] Dongle Host Driver, version 1.88.45.4 (r420671)
[ 50.774222@1] Compiled in drivers/net/wireless/bcmdhd on Jan 13 2016 at 11:50:30
[ 50.774226@1] dhd_module_init: Exit error=0
[ 50.885847@1] dhd_open: Enter ec424000
[ 50.885918@1] dhd_conf_set_fw_name_by_chip: firmware_path=/etc/wifi/40183/fw_bcm43341b0_ag.bin
[ 50.892559@1]
[ 50.892559@1] Dongle Host Driver, version 1.88.45.4 (r420671)
[ 50.892559@1] Compiled in drivers/net/wireless/bcmdhd on Jan 13 2016 at 11:50:30
[ 50.908267@1] wl_android_wifi_on in 1
[ 50.910954@1] wl_android_wifi_on in 2: g_wifi_on=0
[ 50.910969@1] WIFI Disable! 6
[ 51.112281@1] WIFI Enable! 6
[ 51.313280@1] sdio_reset_comm():
[ 51.332391@1] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 51.334397@1] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 51.341112@1] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 51.347428@1] sdio: queuing unknown CIS tuple 0x80 (7 bytes)
[ 51.408700@1] [sdio_reinit] finish
[ 51.515765@1] =========== WLAN going back to live ========
[ 51.516199@1]
[ 51.516199@1]
[ 51.516199@1] dhd_bus_devreset: == WLAN ON ==
[ 51.524885@3] dhd_bus_devreset called when dongle is not in reset
[ 51.529780@3] Will call dhd_bus_start instead
[ 51.533858@1] dhd_conf_set_fw_name_by_chip: firmware_path=/etc/wifi/40183/fw_bcm43341b0_ag.bin
[ 51.547976@3] dhd_conf_read_config: fw_count=4
[ 51.548012@3] dhd_conf_read_config: name=fw_bcm4339a0e_ag.bin, mac_count=5
[ 51.553840@3] dhd_conf_read_config: oui=0x0022F4, nic_start=0xE85408, nic_end=0xE8549D
[ 51.561536@3] dhd_conf_read_config: oui=0x983B16, nic_start=0x3557A9, nic_end=0x35582A
[ 51.570114@3] dhd_conf_read_config: oui=0x983B16, nic_start=0x406927, nic_end=0x406A20
[ 51.577678@3] dhd_conf_read_config: oui=0x983B16, nic_start=0x6E25BB, nic_end=0x6E269A
[ 51.585438@3] dhd_conf_read_config: oui=0x983B16, nic_start=0x916157, nic_end=0x916487
[ 51.593412@3] dhd_conf_read_config: name=fw_bcm4339a0e_ag_p2p.bin, mac_count=5
[ 51.600274@3] dhd_conf_read_config: oui=0x0022F4, nic_start=0xE85408, nic_end=0xE8549D
[ 51.608263@3] dhd_conf_read_config: oui=0x983B16, nic_start=0x3557A9, nic_end=0x35582A
[ 51.616054@3] dhd_conf_read_config: oui=0x983B16, nic_start=0x406927, nic_end=0x406A20
[ 51.623939@3] dhd_conf_read_config: oui=0x983B16, nic_start=0x6E25BB, nic_end=0x6E269A
[ 51.631818@3] dhd_conf_read_config: oui=0x983B16, nic_start=0x916157, nic_end=0x916487
[ 51.639716@3] dhd_conf_read_config: name=fw_bcm4339a0e_ag_apsta.bin, mac_count=5
[ 51.647084@3] dhd_conf_read_config: oui=0x0022F4, nic_start=0xE85408, nic_end=0xE8549D
[ 51.654969@3] dhd_conf_read_config: oui=0x983B16, nic_start=0x3557A9, nic_end=0x35582A
[ 51.662859@3] dhd_conf_read_config: oui=0x983B16, nic_start=0x406927, nic_end=0x406A20
[ 51.670774@3] dhd_conf_read_config: oui=0x983B16, nic_start=0x6E25BB, nic_end=0x6E269A
[ 51.678646@3] dhd_conf_read_config: oui=0x983B16, nic_start=0x916157, nic_end=0x916487
[ 51.686619@3] dhd_conf_read_config: name=fw_bcm4339a0e_ag_mfg.bin, mac_count=5
[ 51.693734@3] dhd_conf_read_config: oui=0x0022F4, nic_start=0xE85408, nic_end=0xE8549D
[ 51.701600@3] dhd_conf_read_config: oui=0x983B16, nic_start=0x3557A9, nic_end=0x35582A
[ 51.709497@3] dhd_conf_read_config: oui=0x983B16, nic_start=0x406927, nic_end=0x406A20
[ 51.717671@3] dhd_conf_read_config: oui=0x983B16, nic_start=0x6E25BB, nic_end=0x6E269A
[ 51.725366@3] dhd_conf_read_config: oui=0x983B16, nic_start=0x916157, nic_end=0x916487
[ 51.733201@3] dhd_conf_read_config: nv_count=1
[ 51.737570@3] dhd_conf_read_config: name=nvram_ap6335e.txt, mac_count=5
[ 51.744174@3] dhd_conf_read_config: oui=0x0022F4, nic_start=0xE85408, nic_end=0xE8549D
[ 51.752049@3] dhd_conf_read_config: oui=0x983B16, nic_start=0x3557A9, nic_end=0x35582A
[ 51.759952@3] dhd_conf_read_config: oui=0x983B16, nic_start=0x406927, nic_end=0x406A20
[ 51.767846@3] dhd_conf_read_config: oui=0x983B16, nic_start=0x6E25BB, nic_end=0x6E269A
[ 51.775746@3] dhd_conf_read_config: oui=0x983B16, nic_start=0x916157, nic_end=0x916487
[ 51.784347@3] dhd_conf_read_config: bcn_timeout = 20
[ 51.788658@3] dhd_conf_read_config: kso_enable = 0
[ 51.793366@3] sdioh_cis_read: func_cis_ptr[0]=0x10ac
[ 51.812568@1] dhd_conf_set_fw_name_by_mac: fw_typ=0 != fw_type_new=2
[ 51.813303@1] dhd_conf_set_fw_name_by_mac: fw_typ=0 != fw_type_new=1
[ 51.819618@1] dhd_conf_set_fw_name_by_mac: fw_typ=0 != fw_type_new=3
[ 51.825986@1] sdioh_cis_read: func_cis_ptr[0]=0x10ac
[ 51.847053@1] Final fw_path=/etc/wifi/40183/fw_bcm43341b0_ag.bin
[ 51.847428@1] Final nv_path=/etc/wifi/40183/nvram.txt
[ 51.852471@1] Final conf_path=/system/etc/wifi/config.txt
[ 51.975522@1] NVRAM version: AP6330_NVRAM_V1.0_20121130
[ 51.976197@1] dhdsdio_write_vars: Download, Upload and compare of NVRAM succeeded.
[ 52.093887@1] dhd_bus_init: enable 0x06, ready 0x06 (waited 0us)
[ 52.094508@1] bcmsdh_set_drvdata: Enter
[ 52.098070@1] bcmsdh_register_oob_intr: Enter
[ 52.102491@1] bcmsdh_register_oob_intr: IRQ=100 Type=414
[ 52.109497@1] dhd_conf_set_band: Set band 0
[ 52.113826@0] Firmware up: op_mode=0x0015, Broadcom Dongle Host Driver mac=04:e6:76:85:93:71
[ 52.120534@0] dhd_conf_set_country: Set country US, revision 0
[ 52.188036@0] Country code: US (US/0)
[ 52.188327@0] dhd_conf_set_roam: Set roam_off 1
[ 52.197583@0] dhdcdc_set_ioctl: msg->status:ffffffe9
[ 52.198070@0] Driver: 1.88.45.4 (r420671)
[ 52.198070@0] Firmware: wl0: Jan 20 2014 11:06:06 version 6.10.190.43 (r449836) FWID 01-77015d04
[ 52.210725@1] wl_android_wifi_on: Success
[ 52.236236@1] dhd_open: Exit ret=0
[ 52.266642@0] init: untracked pid 2291 exited with status 0
[ 52.949390@0] init: untracked pid 2294 exited with status 0
[ 54.723595@1] CPU2: shutdown
[ 54.873500@1] CPU3: shutdown
[ 55.768643@0] net_ratelimit: 6 callbacks suppressed
[ 55.768683@0] dhd_pno_get_for_batch : wifi location service is not supported
[ 55.791578@0] ANDROID-ERROR) failed to getting batching results
[ 55.792057@0] dhd_pno_stop_for_batch : wifi location service is not supported
[ 55.792062@0] NULL POINTER (_dhd_pno_clear_all_batch_results) : head->next is NULL
[ 55.792063@0] NULL POINTER (_dhd_pno_clear_all_batch_results) : head->next is NULL
[ 55.792066@0] ANDROID-ERROR) failed to stop batching scan
[ 55.844812@0] CFGP2P-ERROR) wl_cfgp2p_del_p2p_disc_if : P2P interface unregistered
[ 55.953866@1] dhd_stop: Enter ec424000
[ 55.954969@1] wl_android_wifi_off in 1
[ 55.955709@1] wl_android_wifi_off in 2: g_wifi_on=1
[ 55.963910@0] dhd_rx_frame: net device is NOT registered yet. drop packet
[ 55.967953@1] bcmsdh_set_irq: Flag = 0
[ 55.971178@1] dhd_bus_devreset: WLAN OFF DONE
[ 55.975559@1] =========== WLAN placed in RESET ========
[ 55.980737@1] wl_android_wifi_off out
[ 55.984442@1] dhd_stop: Exit
[ 56.290532@1] dhd_module_cleanup: Enter
[ 56.312956@1] bcmsdh_unregister_oob_intr: Enter
[ 56.313023@1] dhd_detach(): thread:dhd_sysioc:897 terminated OK
[ 56.403021@1] dhd_detach(): thread:dhd_watchdog_thread:895 terminated OK
[ 56.404099@0] dhd_dpc_thread: Unexpected up_cnt 0
[ 56.408816@1] dhd_detach(): thread:dhd_dpc:896 terminated OK
[ 56.416437@1] CFG80211-ERROR) wl_event_handler : was terminated
[ 56.420331@1] wl_destroy_event_handler(): thread:wl_event_handler:893 terminated OK
[ 56.663210@1] WIFI Disable! 6
[ 56.663236@1] =========== WLAN placed in POWER OFF ========
[ 56.666177@1] wifi_teardown_dt
[ 56.669222@1] wifi_request_32k_clk : ON-->OFF for sdio_wifi
[ 56.674791@1] dhd_module_cleanup: Exit
[ 58.075008@0] [aml-i2s-dai]aiu i2s playback disable
[ 58.075008@0]
[ 58.075902@0] [aml-i2s-dai]audio_hw_958_enable 0
[ 58.080624@0] IEC958 16bit
[ 58.083455@0] hdmitx: audio: aout notify rate 48000
[ 58.088190@0] hdmitx: audio: aout notify size 16
[ 58.092729@0] hdmitx: audio: no update
[ 58.096537@0] aml_i2s_close device type 8
[ 63.103013@0] speaker_events--mute =0
Comments