RobertBerger icon

phyboard-mira-imx6-3-6 SD card boot log

RobertBerger | PRO | 07/17/22 01:50:24 PM UTC | 0 ⭐ | 622 👁️ | Never ⏰ | []
text |

25.38 KB

|

None

|

0 👍

/

0 👎

barebox 2021.04.0-bsp-yocto-ampliphy-i.mx6-pd21.1.1 #1 Thu Jul 14 09:03:12 UTC 2022
  Board: PHYTEC phyCORE-i.MX6 Quad with NAND
detected i.MX6 Quad revision 1.5
i.MX reset reason WDG (SRSR: 0x00000010)
i.MX6 Quad unique ID: 121821d4ee6ba5b5
mdio_bus: miibus0: probed   
eth0: got preset MAC address: 50:2d:f4:16:2d:bd
nand_base: device found, Manufacturer ID: 0xef, Chip ID: 0xd3
nand_base: Winbond W29N08GV 
nand_base: 1024 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
Bad block table found at page 524224, version 0x01
Bad block table found at page 524160, version 0x01
m25p80 flash@00: n25q128a13 (16384 Kbytes)
imx-usb [email protected]: USB EHCI 1.00
imx-esdhc [email protected]: registered as mmc0
da9063 da90620: da9062 with id 62.12.ff.1a detected
state: New state registered 'state'
state: Using bucket 0@0x00000000
netconsole: registered as netconsole-1
phySOM-i.MX6: Using environment in MMC
malloc space: 0x2fe7a760 -> 0x4fcf4ebf (size 510.5 MiB)
mmc0: detected SD card version 2.0
mmc0: registered mmc0
 Hit m for menu or any to stop autoboot:    1
Booting entry 'mmc'
Found node /soc/bus@2000000 
mounted /dev/mmc0.0 on /mnt/mmc0.0
ext4 ext40: EXT2 rev 1, inode_size 256, descriptor size 64
mounted /dev/mmc0.1 on /mnt/mmc0.1
 Loading ARM Linux zImage '/mnt/mmc0.0/zImage'
Loading devicetree from '/mnt/mmc0.0/oftree'
commandline: consoleblank=0 console=ttymxc1,115200n8  root=/dev/mmcblk0p2 rootflags=data=journal imxdrm.legacyfb_depth=32 rootwait ro fsck.repair=yes
Starting kernel in secure mode
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 5.19.0-rc6 (oe-user@oe-host) (arm-phytec-linux-gnueabi-gcc (GCC) 10.3.0, GNU ld (GNU Binutils) 2.36.1.20210703) #1 SMP Wed Jul 13 19:08:14 UTC 2022
[    0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] OF: fdt: Machine model: PHYTEC phyBOARD-Mira Quad Carrier-Board with NAND
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] efi: UEFI not found.
[    0.000000] cma: Reserved 64 MiB at 0x4b800000
[    0.000000] Zone ranges: 
[    0.000000]   DMA      [mem 0x0000000010000000-0x000000003fffffff]
[    0.000000]   Normal   empty
[    0.000000]   HighMem  [mem 0x0000000040000000-0x000000004fffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000010000000-0x000000004fffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff]
[    0.000000] percpu: Embedded 17 pages/cpu s37652 r8192 d23788 u69632
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 260608
[    0.000000] Kernel command line: consoleblank=0 console=ttymxc1,115200n8  root=/dev/mmcblk0p2 rootflags=data=journal imxdrm.legacyfb_depth=32 rootwait ro fsck.repair=yes
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 944972K/1048576K available (15360K kernel code, 2490K rwdata, 6008K rodata, 2048K init, 431K bss, 38068K reserved, 65536K cma-reserved, 195592K highmem)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] trace event string verifier disabled
[    0.000000] rcu: Hierarchical RCU implementation.
[    0.000000] rcu:     RCU event tracing is enabled.
[    0.000000] rcu:     RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4.
[    0.000000]  Tracing variant of Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] L2C-310 errata 752271 769419 enabled
[    0.000000] L2C-310 enabling early BRESP for Cortex-A9
[    0.000000] L2C-310 full line of zeros enabled for Cortex-A9
[    0.000000] L2C-310 ID prefetch enabled, offset 16 lines
[    0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled
[    0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB
[    0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001
[    0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[    0.000000] Switching to timer-based delay loop, resolution 333ns
[    0.000001] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns
[    0.000034] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns
[    0.009355] Console: colour dummy device 80x30
[    0.009480] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000)
[    0.009507] pid_max: default: 32768 minimum: 301
[    0.009918] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[    0.009965] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[    0.011134] CPU: Testing write buffer coherency: ok
[    0.011239] CPU0: Spectre v2: using BPIALL workaround
[    0.011779] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.013321] cblist_init_generic: Setting adjustable number of callback queues.
[    0.013341] cblist_init_generic: Setting shift to 2 and lim to 1.
[    0.013626] Setting up static identity map for 0x10300000 - 0x103000ac
[    0.017428] rcu: Hierarchical SRCU implementation.
[    0.025741] EFI services will not be available.
[    0.026424] smp: Bringing up secondary CPUs ...
[    0.027813] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.027843] CPU1: Spectre v2: using BPIALL workaround
[    0.029428] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
[    0.029454] CPU2: Spectre v2: using BPIALL workaround
[    0.031037] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
[    0.031067] CPU3: Spectre v2: using BPIALL workaround
[    0.031247] smp: Brought up 1 node, 4 CPUs
[    0.031272] SMP: Total of 4 processors activated (24.00 BogoMIPS).
[    0.031292] CPU: All CPU(s) started in SVC mode.
[    0.032248] devtmpfs: initialized
[    0.048586] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[    0.048979] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.049022] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[    0.055263] pinctrl core: initialized pinctrl subsystem
[    0.058413] DMI not present or invalid.
[    0.059814] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[    0.065824] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.071342] thermal_sys: Registered thermal governor 'step_wise'
[    0.071755] cpuidle: using governor menu
[    0.072240] CPU identified as i.MX6Q, silicon rev 1.5
[    0.131265] platform 2400000.ipu: Fixing up cyclic dependency with 120000.hdmi
[    0.131419] platform 2400000.ipu: Fixing up cyclic dependency with 20e0000.iomuxc-gpr:ipu1_csi0_mux
[    0.133732] platform 2800000.ipu: Fixing up cyclic dependency with 120000.hdmi
[    0.133876] platform 2800000.ipu: Fixing up cyclic dependency with 20e0000.iomuxc-gpr:ipu2_csi1_mux
[    0.149665] No ATAGs?
[    0.149925] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[    0.149947] hw-breakpoint: maximum watchpoint size is 4 bytes.
[    0.156681] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver
[    0.170694] Serial: AMBA PL011 UART driver
[    0.229591] mxs-dma 110000.dma-apbh: initialized
[    0.245038] iommu: Default domain type: Translated
[    0.245055] iommu: DMA domain TLB invalidation policy: strict mode
[    0.246529] SCSI subsystem initialized
[    0.247406] usbcore: registered new interface driver usbfs
[    0.247496] usbcore: registered new interface driver hub
[    0.247575] usbcore: registered new device driver usb
[    0.247984] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator
[    0.248241] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests
[    0.248522] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator
[    0.248775] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests
[    0.252681] i2c i2c-0: IMX I2C adapter registered
[    0.254017] i2c i2c-1: IMX I2C adapter registered
[    0.256678] i2c i2c-2: IMX I2C adapter registered
[    0.259246] pps_core: LinuxPPS API ver. 1 registered
[    0.259259] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <[email protected]>
[    0.259296] PTP clock support registered
[    0.259757] EDAC MC: Ver: 3.0.0
[    0.265962] vgaarb: loaded
[    2.545029] clocksource: Switched to clocksource mxc_timer1
[    2.564443] NET: Registered PF_INET protocol family
[    2.565343] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear)
[    2.568981] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[    2.569043] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    2.569085] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear)
[    2.569244] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear)
[    2.569522] TCP: Hash tables configured (established 8192 bind 8192)
[    2.569888] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[    2.569970] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
[    2.570328] NET: Registered PF_UNIX/PF_LOCAL protocol family
[    2.571429] RPC: Registered named UNIX socket transport module.
[    2.571448] RPC: Registered udp transport module.
[    2.571458] RPC: Registered tcp transport module.
[    2.571466] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    2.571482] PCI: CLS 0 bytes, default 64
[    2.572623] armv7-pmu pmu: hw perfevents: no interrupt-affinity property, guessing.
[    2.624696] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
[    2.628475] Initialise system trusted keyrings
[    2.628973] workingset: timestamp_bits=30 max_order=18 bucket_order=0
[    2.640578] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    2.641914] NFS: Registering the id_resolver key type
[    2.641988] Key type id_resolver registered
[    2.642002] Key type id_legacy registered
[    2.642185] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    2.642199] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering...
[    2.642258] ntfs: driver 2.1.32 [Flags: R/O].
[    2.643109] Key type asymmetric registered
[    2.643125] Asymmetric key parser 'x509' registered
[    2.643410] bounce: pool size: 64 pages
[    2.643618] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[    2.643635] io scheduler mq-deadline registered
[    2.643647] io scheduler kyber registered
[    2.760113] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2
[    2.760149] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware
[    2.870627] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled
[    2.880110] SuperH (H)SCI(F) driver initialized
[    2.882256] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 269, base_baud = 5000000) is a IMX
[    3.753760] printk: console [ttymxc1] enabled
[    3.760682] msm_serial: driver initialized
[    3.764800] STMicroelectronics ASC driver initialized
[    3.773339] STM32 USART driver initialized
[    3.817265] brd: module loaded
[    3.833625] loop: module loaded
[    3.837506] at24 2-0050: supply vcc not found, using dummy regulator
[    3.845024] at24 2-0050: 4096 byte 24c32 EEPROM, writable, 32 bytes/write
[    3.870159] nand: device found, Manufacturer ID: 0xef, Chip ID: 0xd3
[    3.876586] nand: Winbond W29N08GV
[    3.880005] nand: 1024 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    3.888703] Bad block table found at page 524224, version 0x01
[    3.894912] Bad block table found at page 524160, version 0x01
[    3.901289] 3 fixed-partitions partitions found on MTD device gpmi-nand
[    3.907985] Creating 3 MTD partitions on "gpmi-nand":
[    3.913061] 0x000000000000-0x000001000000 : "barebox"
[    3.920997] 0x000001000000-0x000001100000 : "barebox-environment"
[    3.929759] 0x000001100000-0x000040000000 : "root"
[    3.943912] gpmi-nand 112000.nand-controller: driver registered.
[    3.967165] CAN device driver interface
[    3.973761] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded
[    3.983020] e1000e: Intel(R) PRO/1000 Network Driver
[    3.988042] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[    3.994086] igb: Intel(R) Gigabit Ethernet Network Driver
[    3.999559] igb: Copyright (c) 2007-2014 Intel Corporation.
[    4.017419] pegasus: Pegasus/Pegasus II USB Ethernet driver
[    4.023089] usbcore: registered new interface driver pegasus
[    4.028891] usbcore: registered new interface driver asix
[    4.034368] usbcore: registered new interface driver ax88179_178a
[    4.040580] usbcore: registered new interface driver cdc_ether
[    4.046567] usbcore: registered new interface driver smsc75xx
[    4.052427] usbcore: registered new interface driver smsc95xx
[    4.058297] usbcore: registered new interface driver net1080
[    4.064033] usbcore: registered new interface driver cdc_subset
[    4.070061] usbcore: registered new interface driver zaurus
[    4.075817] usbcore: registered new interface driver cdc_ncm
[    4.088717] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    4.095329] ehci-pci: EHCI PCI platform driver
[    4.099869] ehci-platform: EHCI generic platform driver
[    4.105705] ehci-omap: OMAP-EHCI Host Controller driver
[    4.111295] ehci-orion: EHCI orion driver
[    4.115781] SPEAr-ehci: EHCI SPEAr driver
[    4.120161] ehci-st: EHCI STMicroelectronics driver
[    4.125460] ehci-atmel: EHCI Atmel driver
[    4.129822] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    4.136093] ohci-pci: OHCI PCI platform driver
[    4.140650] ohci-platform: OHCI generic platform driver
[    4.146442] SPEAr-ohci: OHCI SPEAr driver
[    4.150840] ohci-st: OHCI STMicroelectronics driver
[    4.156150] ohci-atmel: OHCI Atmel driver
[    4.161738] usbcore: registered new interface driver usb-storage
[    4.183457] i2c_dev: i2c /dev entries driver
[    4.232035] sdhci: Secure Digital Host Controller Interface driver
[    4.238285] sdhci: Copyright(c) Pierre Ossman
[    4.248097] Synopsys Designware Multimedia Card Interface Driver
[    4.258969] sdhci-pltfm: SDHCI platform and OF driver helper
[    4.267277] sdhci-esdhc-imx 2190000.mmc: Got CD GPIO
[    4.278505] ledtrig-cpu: registered to indicate activity on CPUs
[    4.287649] caam 2100000.crypto: Entropy delay = 3200
[    4.310424] mmc0: SDHCI controller on 2190000.mmc [2190000.mmc] using ADMA
[    4.353517] caam 2100000.crypto: Instantiated RNG4 SH0
[    4.354605] mmc0: new high speed SDHC card at address 59b4
[    4.365809] mmcblk0: mmc0:59b4 USDU1 29.4 GiB
[    4.375303]  mmcblk0: p1 p2
[    4.414283] caam 2100000.crypto: Instantiated RNG4 SH1
[    4.419489] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4)
[    4.426162] caam 2100000.crypto: job rings = 2, qi = 0
[    4.442270] caam algorithms registered in /proc/crypto
[    4.447781] caam 2100000.crypto: registering rng-caam
[    4.475453] caam 2100000.crypto: rng crypto API alg registered prng-caam
[    4.485601] usbcore: registered new interface driver usbhid
[    4.491201] usbhid: USB HID core driver
[    4.512573] NET: Registered PF_INET6 protocol family
[    4.519753] Segment Routing with IPv6
[    4.523538] In-situ OAM (IOAM) with IPv6
[    4.527735] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[    4.534857] NET: Registered PF_PACKET protocol family
[    4.539990] can: controller area network core
[    4.544486] NET: Registered PF_CAN protocol family
[    4.549352] can: raw protocol
[    4.552342] can: broadcast manager protocol
[    4.556586] can: netlink gateway - max_hops=1
[    4.561439] Key type dns_resolver registered
[    4.567923] ThumbEE CPU extension supported.
[    4.572228] Registering SWP/SWPB emulation handler
[    4.578311] Loading compiled-in X.509 certificates
[    4.657458] random: crng init done
[    4.675969] ci_hdrc ci_hdrc.1: EHCI Host Controller
[    4.680911] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1
[    4.715079] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00
[    4.721830] hub 1-0:1.0: USB hub found
[    4.725725] hub 1-0:1.0: 1 port detected
[    4.758186] imx-uart 21ec000.serial: deferred probe timeout, ignoring dependency
[    4.772529] input: gpio-keys as /devices/platform/gpio-keys/input/input0
[    4.791980] imx-uart 21ec000.serial: deferred probe timeout, ignoring dependency
[    4.810416] EXT4-fs: Warning: mounting with data=journal disables delayed allocation, dioread_nolock, O_DIRECT and fast_commit support!
[    4.823409] EXT4-fs: Mount option(s) incompatible with ext2
[    4.835284] EXT4-fs (mmcblk0p2): mounted filesystem with journalled data mode. Quota mode: disabled.
[    4.844519] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
[    4.852185] devtmpfs: mounted
[    4.862590] Freeing unused kernel image (initmem) memory: 2048K
[    4.896165] Run /sbin/init as init process
[    5.236466] systemd[1]: systemd 247.6+ running in system mode. (-PAM -AUDIT -SELINUX -IMA -APPARMOR -SMACK -SYSVINIT -UTMP -LIBCRYPTSETUP -GCRYPT -GNUTLS -ACL -XZ +LZ4 -ZSTD -SECCOMP +BLKID -ELFUTILS +KMOD -IDN2 -IDN -PCRE2 default-hierarchy=hybrid)
[    5.259988] systemd[1]: Detected architecture arm.
 Welcome to The ampliPHY Distribution BSP-Yocto-Ampliphy-i.MX6-PD21.1.1!
 [    5.306204] systemd[1]: Set hostname to <phyboard-mira-imx6-3>.
[    5.350496] systemd[1]: Using hardware watchdog 'imx2+ watchdog', version 0, device /dev/watchdog
[    5.359622] systemd[1]: Set hardware watchdog to 1min.
[    6.109826] systemd[1]: Queued start job for default target Multi-User System.
[    6.121908] systemd[1]: Created slice system-getty.slice.
[  OK  ] Created slice system-getty.slice.
[    6.156612] systemd[1]: Created slice system-modprobe.slice.
[  OK  ] Created slice system-modprobe.slice.
[    6.196629] systemd[1]: Created slice system-serial\x2dgetty.slice.
[  OK  ] Created slice system-serial\x2dgetty.slice.
[    6.236283] systemd[1]: Created slice User and Session Slice.
[  OK  ] Created slice User and Session Slice.
[    6.275899] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[  OK  ] Started Dispatch Password …ts to Console Directory Watch.
[    6.315769] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[  OK  ] Started Forward Password R…uests to Wall Directory Watch.
[    6.355943] systemd[1]: Reached target Paths.
[  OK  ] Reached target Paths.
[    6.385564] systemd[1]: Reached target Remote File Systems.
[  OK  ] Reached target Remote File Systems.
[    6.425395] systemd[1]: Reached target Slices.
[  OK  ] Reached target Slices.
[    6.455667] systemd[1]: Reached target Swap.
[  OK  ] Reached target Swap.
[    6.492802] systemd[1]: Condition check resulted in Journal Audit Socket being skipped.
[    6.502227] systemd[1]: Listening on Journal Socket (/dev/log).
[  OK  ] Listening on Journal Socket (/dev/log).
[    6.536574] systemd[1]: Listening on Journal Socket.
[  OK  ] Listening on Journal Socket.
[    6.576725] systemd[1]: Listening on Network Service Netlink Socket.
[  OK  ] Listening on Network Service Netlink Socket.
[    6.616651] systemd[1]: Listening on udev Control Socket.
[  OK  ] Listening on udev Control Socket.
[    6.656224] systemd[1]: Listening on udev Kernel Socket.
[  OK  ] Listening on udev Kernel Socket.
[    6.696236] systemd[1]: Condition check resulted in Huge Pages File System being skipped.
[    6.705433] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped.
[    6.720648] systemd[1]: Mounting Kernel Debug File System...
         Mounting Kernel Debug File System...
[    6.761227] systemd[1]: Mounting Kernel Trace File System...
         Mounting Kernel Trace File System...
[    6.807524] systemd[1]: Mounting Temporary Directory (/tmp)...
         Mounting Temporary Directory (/tmp)...
[    6.845981] systemd[1]: Condition check resulted in Create list of static device nodes for the current kernel being skipped.
[    6.864312] systemd[1]: Starting Load Kernel Module configfs...
         Starting Load Kernel Module configfs...
[    6.901690] systemd[1]: Starting Load Kernel Module drm...
         Starting Load Kernel Module drm...
[    6.941766] systemd[1]: Starting Load Kernel Module fuse...
         Starting Load Kernel Module fuse...
[    6.981517] systemd[1]: Starting File System Check on Root Device...
         Starting File System Check on Root Device...
[    7.028440] systemd[1]: Starting Journal Service...
         Starting Journal Service...
[    7.040140] systemd[1]: Condition check resulted in Load Kernel Modules being skipped.
[    7.056117] systemd[1]: Starting Apply Kernel Variables...
         Starting Apply Kernel Variables...
[    7.069925] systemd[1]: Starting Coldplug All udev Devices...
         Starting Coldplug All udev Devices...
[    7.099973] systemd[1]: Mounted Kernel Debug File System.
[  OK  ] Mounted     7.107307] systemd[1]: Mounted Kernel Trace File System.
;39mKernel Debug File System.[    7.115482] systemd[1]: Mounted Temporary Directory (/tmp).
 [  OK  ] Mounted Kernel Trace File System systemd[1]: [email protected]: Succeeded.
[0m.
[  OK  ] Mounted[    7.136064] systemd[1]: Finished Load Kernel Module configfs.
 Temporary Directory (/tmp).
[  OK  ] F[    7.146028] systemd[1]: [email protected]: Succeeded.
inished Load Kernel Modu[    7.155608] systemd[1]: Finished Load Kernel Module drm.
le configfs.
[  OK  ] Finished     7.164723] systemd[1]: [email protected]: Succeeded.
0;1;39mLoad Kernel Module drm[    7.173229] systemd[1]: Finished Load Kernel Module fuse.
.
[  OK  ] Finished Load Kernel Module fuse.
[    7.248598] systemd[1]: Finished File System Check on Root Device.
[  OK  ] Finished File System Check on Root Device.
[    7.286361] systemd[1]: Started Journal Service.
[  OK  ] Started Journal Service.
[  OK  ] Finished Apply Kernel Variables.
         Mounting Kernel Configuration File System...
         Starting Remount Root and Kernel File Systems...
[  OK  ] Mounted Kernel Configuration File System.
[    7.464712] EXT4-fs (mmcblk0p2): re-mounted. Quota mode: disabled.
[  OK  ] Finished Remount Root and Kernel File Systems.
         Starting Flush Journal to Persistent Storage...
[    7.564904] systemd-journald[161]: Received client request to flush runtime journal.
         Starting Create Static Device Nodes in /dev...
[  OK  ] Finished Flush Journal to Persistent Storage.
[  OK  ] Finished Create Static Device Nodes in /dev.
[  OK  ] Reached target Local File Systems (Pre).
         Mounting /var/volatile...
         Starting Rule-based Manage…for Device Events and Files...
[  OK  ] Mounted /var/volatile.
[  OK  ] Reached target Local File Systems.
         Starting Create Volatile Files and Directories...
[  OK  ] Started Rule-based Manager for Device Events and Files.
         Starting Network Service...
[  OK  ] Finished Create Volatile Files and Directories.
         Starting Network Time Synchronization...
[  OK  ] Started Network Service.
         Starting Network Name Resolution...
[  OK  ] Started Network Time Synchronization.
[  OK  ] Reached target System Time Set.
[  OK  ] Reached target System Time Synchronized.
[  OK  ] Started Network Name Resolution.
[  OK  ] Reached target Network.
[  OK  ] Reached target Host and Network Name Lookups.
[    9.876691] mtdblock: MTD device 'barebox' is NAND, please consider using UBI block devices instead.
[    9.876855] mtdblock: MTD device 'barebox-environment' is NAND, please consider using UBI block devices instead.
[    9.879676] mtdblock: MTD device 'root' is NAND, please consider using UBI block devices instead.
[  OK  ] Finished Coldplug All udev Devices.
[  OK  ] Reached target System Initialization.
[  OK  ] Started Daily Cleanup of Temporary Directories.
[  OK  ] Reached target Timers.
[  OK  ] Reached target Hardware activated USB gadget.
[  OK  ] Listening on D-Bus System Message Bus Socket.
[  OK  ] Reached target Sockets.
[  OK  ] Reached target Basic System.
[  OK  ] Listening on Load/Save RF …itch Status /dev/rfkill Watch.
[  OK  ] Started D-Bus System Message Bus.
[  OK  ] Started Getty on tty1.
[  OK  ] Started Serial Getty on ttymxc1.
[  OK  ] Reached target Login Prompts.
         Starting User Login Management...
[  OK  ] Started User Login Management.
[  OK  ] Reached target Multi-User System.
  ____   _   _ __   __ _____  _____   ____
|  _ \ | | | |\ \ / /|_   _|| ____| / ___|
| |_) || |_| | \ V /   | |  |  _|  | |
|  __/ |  _  |  | |    | |  | |___ | |___
|_|    |_| |_|  |_|    |_|  |_____| \____|
     _     __  __  ____   _      ___  ____   _   _ __   __
   / \   |  \/  ||  _ \ | |    |_ _||  _ \ | | | |\ \ / /
  / _ \  | |\/| || |_) || |     | | | |_) || |_| | \ V /
 / ___ \ | |  | ||  __/ | |___  | | |  __/ |  _  |  | |
/_/   \_\|_|  |_||_|    |_____||___||_|    |_| |_|  |_|
  ampliPHY (Phytec Base Distribution) BSP-Yocto-Ampliphy-i.MX6-PD21.1.1 phyboard-mira-imx6-3 ttymxc1
 phyboard-mira-imx6-3 login: 
 

Comments