Configured MCU 'z' (660 moves)
Loaded MCU 'z' 60 commands (v0.6.0-61-gf70fefa-20180508_003820-octopi / gcc: (GCC) 4.8.1 binutils: (GNU Binutils) 2.24)
MCU 'z' config: ADC_MAX=1023 PWM_MAX=255 CLOCK_FREQ=16000000 SOFT_PWM_MAX=256 SERIAL_BAUD=250000 MCU=atmega2560 STATS_SUMSQ_BASE=256
Starting heater checks for heater_bed
Starting heater checks for extruder
Restarting printer
Start printer at Mon May 21 22:33:29 2018 (1526956409.5 12505.7)
===== Config file =====
[stepper_x]
step_pin = ar54
dir_pin = !ar55
enable_pin = !ar38
step_distance = 0.005011
endstop_pin = ^!ar3
position_endstop = 0
position_max = 282
homing_speed = 45
[stepper_y]
step_pin = ar46
dir_pin = ar48
enable_pin = !ar62
step_distance = 0.005011
endstop_pin = ^!ar14
position_endstop = 0
position_max = 300
homing_speed = 45
[stepper_z]
step_pin = z:ar54
dir_pin = z:ar55
enable_pin = !z:ar38
step_distance = 0.000313
endstop_pin = probe:z_virtual_endstop
position_endstop = 1.7
position_max = 300
position_min = -0.35
homing_speed = 4
[stepper_z1]
step_pin = z:ar60
dir_pin = z:ar61
enable_pin = !z:ar56
step_distance = 0.000313
[stepper_z2]
step_pin = z:ar46
dir_pin = z:ar48
enable_pin = !z:ar62
step_distance = 0.000313
[extruder]
step_pin = ar26
dir_pin = ar28
enable_pin = !ar24
step_distance = 0.001150
nozzle_diameter = 0.400
pressure_advance = 0.05
filament_diameter = 1.750
heater_pin = ar10
sensor_type = ATC Semitec 104GT-2
sensor_pin = analog13
control = pid
pid_kp = 16.459
pid_ki = 1.291
pid_kd = 52.465
min_temp = 0
max_temp = 300
[heater_bed]
heater_pin = ar8
sensor_type = EPCOS 100K B57560G104F
sensor_pin = analog14
control = pid
pid_kp = 47.076
pid_ki = 0.659
pid_kd = 840.308
min_temp = 0
max_temp = 130
[servo bltouch]
pin = z:ar11
maximum_servo_angle = 180
minimum_pulse_width = 0.0006
maximum_pulse_width = 0.0024
[probe]
pin = z:ar19
z_offset = 1.7
activate_gcode =
SET_SERVO SERVO=bltouch ANGLE=10
SET_SERVO SERVO=bltouch ANGLE=60
G4 P200
deactivate_gcode =
SET_SERVO SERVO=bltouch ANGLE=90
[homing_override]
set_position_z = 5
gcode =
G90
G1 Z7 F600
G28 X0 Y0
G1 X150 Y150 F3600
G28 Z0
G1 X0 Y0 F3600
[z_tilt]
z_positions =
-56.17,0
-56.17,235
362.43,103
points =
10,21
10,210
282,103
horizontal_move_z = 8
[fan]
pin = ar9
[mcu z]
serial = /dev/serial/by-path/platform-3f980000.usb-usb-0:1.2:1.0-port0
pin_map = arduino
[mcu]
serial = /dev/serial/by-path/platform-3f980000.usb-usb-0:1.3:1.0-port0
pin_map = arduino
[printer]
kinematics = corexy
max_velocity = 1600
max_accel = 3000
max_z_velocity = 8
max_z_accel = 50
=======================
Starting serial connect
Attempting MCU 'mcu' reset
Attempting MCU 'z' reset
Restarting printer
Start printer at Mon May 21 22:33:32 2018 (1526956412.1 12508.3)
===== Config file =====
[stepper_x]
step_pin = ar54
dir_pin = !ar55
enable_pin = !ar38
step_distance = 0.005011
endstop_pin = ^!ar3
position_endstop = 0
position_max = 282
homing_speed = 45
[stepper_y]
step_pin = ar46
dir_pin = ar48
enable_pin = !ar62
step_distance = 0.005011
endstop_pin = ^!ar14
position_endstop = 0
position_max = 300
homing_speed = 45
[stepper_z]
step_pin = z:ar54
dir_pin = z:ar55
enable_pin = !z:ar38
step_distance = 0.000313
endstop_pin = probe:z_virtual_endstop
position_endstop = 1.7
position_max = 300
position_min = -0.35
homing_speed = 4
[stepper_z1]
step_pin = z:ar60
dir_pin = z:ar61
enable_pin = !z:ar56
step_distance = 0.000313
[stepper_z2]
step_pin = z:ar46
dir_pin = z:ar48
enable_pin = !z:ar62
step_distance = 0.000313
[extruder]
step_pin = ar26
dir_pin = ar28
enable_pin = !ar24
step_distance = 0.001150
nozzle_diameter = 0.400
pressure_advance = 0.05
filament_diameter = 1.750
heater_pin = ar10
sensor_type = ATC Semitec 104GT-2
sensor_pin = analog13
control = pid
pid_kp = 16.459
pid_ki = 1.291
pid_kd = 52.465
min_temp = 0
max_temp = 300
[heater_bed]
heater_pin = ar8
sensor_type = EPCOS 100K B57560G104F
sensor_pin = analog14
control = pid
pid_kp = 47.076
pid_ki = 0.659
pid_kd = 840.308
min_temp = 0
max_temp = 130
[servo bltouch]
pin = z:ar11
maximum_servo_angle = 180
minimum_pulse_width = 0.0006
maximum_pulse_width = 0.0024
[probe]
pin = z:ar19
z_offset = 1.7
activate_gcode =
SET_SERVO SERVO=bltouch ANGLE=10
SET_SERVO SERVO=bltouch ANGLE=60
G4 P200
deactivate_gcode =
SET_SERVO SERVO=bltouch ANGLE=90
[homing_override]
set_position_z = 5
gcode =
G90
G1 Z7 F600
G28 X0 Y0
G1 X150 Y150 F3600
G28 Z0
G1 X0 Y0 F3600
[z_tilt]
z_positions =
-56.17,0
-56.17,235
362.43,103
points =
10,21
10,210
282,103
horizontal_move_z = 8
[fan]
pin = ar9
[mcu z]
serial = /dev/serial/by-path/platform-3f980000.usb-usb-0:1.2:1.0-port0
pin_map = arduino
[mcu]
serial = /dev/serial/by-path/platform-3f980000.usb-usb-0:1.3:1.0-port0
pin_map = arduino
[printer]
kinematics = corexy
max_velocity = 1600
max_accel = 3000
max_z_velocity = 8
max_z_accel = 50
=======================
Starting serial connect
Printer is not ready
The klippy host software is attempting to connect. Please
retry in a few moments.
Sending MCU 'mcu' printer configuration...
Configured MCU 'mcu' (643 moves)
Loaded MCU 'mcu' 60 commands (v0.6.0-61-gf70fefa-20180508_003820-octopi / gcc: (GCC) 4.8.1 binutils: (GNU Binutils) 2.24)
MCU 'mcu' config: ADC_MAX=1023 PWM_MAX=255 CLOCK_FREQ=16000000 SOFT_PWM_MAX=256 SERIAL_BAUD=250000 MCU=atmega2560 STATS_SUMSQ_BASE=256
Starting serial connect
Printer is not ready
The klippy host software is attempting to connect. Please
retry in a few moments.
Sending MCU 'z' printer configuration...
Configured MCU 'z' (660 moves)
Loaded MCU 'z' 60 commands (v0.6.0-61-gf70fefa-20180508_003820-octopi / gcc: (GCC) 4.8.1 binutils: (GNU Binutils) 2.24)
MCU 'z' config: ADC_MAX=1023 PWM_MAX=255 CLOCK_FREQ=16000000 SOFT_PWM_MAX=256 SERIAL_BAUD=250000 MCU=atmega2560 STATS_SUMSQ_BASE=256
Starting heater checks for heater_bed
Starting heater checks for extruder
Calculating bed tilt with: [[10.000176499999998, 20.9993215, 2.0349099999999996], [10.000176499999995, 209.9992085, 1.9704319999999995], [281.999762, 103.00183099999998, 1.4320719999999993]]
Coordinate descent best_err: 1.85144942381e-10 rounds: 184
Calculated bed tilt parameters: {'y_adjust': -0.0003412422554932085, 'x_adjust': -0.002113501722782265, 'z_adjust': 2.0632212880401006}
Calculating bed tilt with: [[10.000176499999998, 20.9993215, 2.332886], [10.000176499999995, 209.9992085, 2.341963], [281.999762, 103.00183099999998, 1.0915279999999994]]
Coordinate descent best_err: 5.44439634087e-11 rounds: 194
Calculated bed tilt parameters: {'y_adjust': 4.802479561316352e-05, 'x_adjust': -0.004578334139563691, 'z_adjust': 2.377663526053874}
Calculating bed tilt with: [[10.000176499999998, 20.9993215, 3.079077999999999], [10.000176499999995, 209.9992085, 3.0656189999999985], [281.999762, 103.00183099999998, 0.4204559999999984]]
Coordinate descent best_err: 2.12600761192e-10 rounds: 196
Calculated bed tilt parameters: {'y_adjust': -7.116593338050959e-05, 'x_adjust': -0.009752939922191048, 'z_adjust': 3.1780997407254645}
Restarting printer
Start printer at Mon May 21 22:38:35 2018 (1526956715.8 12812.1)
===== Config file =====
[stepper_x]
step_pin = ar54
dir_pin = !ar55
enable_pin = !ar38
step_distance = 0.005011
endstop_pin = ^!ar3
position_endstop = 0
position_max = 282
homing_speed = 45
[stepper_y]
step_pin = ar46
dir_pin = ar48
enable_pin = !ar62
step_distance = 0.005011
endstop_pin = ^!ar14
position_endstop = 0
position_max = 300
homing_speed = 45
[stepper_z]
step_pin = z:ar54
dir_pin = z:ar55
enable_pin = !z:ar38
step_distance = 0.000313
endstop_pin = probe:z_virtual_endstop
position_endstop = 1.7
position_max = 300
position_min = -0.35
homing_speed = 4
[stepper_z1]
step_pin = z:ar60
dir_pin = z:ar61
enable_pin = !z:ar56
step_distance = 0.000313
[stepper_z2]
step_pin = z:ar46
dir_pin = z:ar48
enable_pin = !z:ar62
step_distance = 0.000313
[extruder]
step_pin = ar26
dir_pin = ar28
enable_pin = !ar24
step_distance = 0.001150
nozzle_diameter = 0.400
pressure_advance = 0.05
filament_diameter = 1.750
heater_pin = ar10
sensor_type = ATC Semitec 104GT-2
sensor_pin = analog13
control = pid
pid_kp = 16.459
pid_ki = 1.291
pid_kd = 52.465
min_temp = 0
max_temp = 300
[heater_bed]
heater_pin = ar8
sensor_type = EPCOS 100K B57560G104F
sensor_pin = analog14
control = pid
pid_kp = 47.076
pid_ki = 0.659
pid_kd = 840.308
min_temp = 0
max_temp = 130
[servo bltouch]
pin = z:ar11
maximum_servo_angle = 180
minimum_pulse_width = 0.0006
maximum_pulse_width = 0.0024
[probe]
pin = z:ar19
z_offset = 1.7
activate_gcode =
SET_SERVO SERVO=bltouch ANGLE=10
SET_SERVO SERVO=bltouch ANGLE=60
G4 P200
deactivate_gcode =
SET_SERVO SERVO=bltouch ANGLE=90
[homing_override]
set_position_z = 5
gcode =
G90
G1 Z7 F600
G28 X0 Y0
G1 X10 Y0 F3600
G28 Z0
G1 X0 Y0 F3600
[z_tilt]
z_positions =
-56.17,0
-56.17,235
362.43,103
points =
10,21
10,210
282,103
horizontal_move_z = 8
[fan]
pin = ar9
[mcu z]
serial = /dev/serial/by-path/platform-3f980000.usb-usb-0:1.2:1.0-port0
pin_map = arduino
[mcu]
serial = /dev/serial/by-path/platform-3f980000.usb-usb-0:1.3:1.0-port0
pin_map = arduino
[printer]
kinematics = corexy
max_velocity = 1600
max_accel = 3000
max_z_velocity = 8
max_z_accel = 50
=======================
Starting serial connect
Printer is not ready
The klippy host software is attempting to connect. Please
retry in a few moments.
got {'#receive_time': 12813.254195819, u'next_clock': 585512704, u'oid': 3, u'value': 7860, '#name': u'analog_in_state', '#sent_time': 12813.200461040999}
got {'#receive_time': 12813.324437883999, u'next_clock': 586632704, u'oid': 10, u'value': 7847, '#name': u'analog_in_state', '#sent_time': 12813.302610593}
Configured MCU 'mcu' (643 moves)
Loaded MCU 'mcu' 60 commands (v0.6.0-61-gf70fefa-20180508_003820-octopi / gcc: (GCC) 4.8.1 binutils: (GNU Binutils) 2.24)
MCU 'mcu' config: ADC_MAX=1023 PWM_MAX=255 CLOCK_FREQ=16000000 SOFT_PWM_MAX=256 SERIAL_BAUD=250000 MCU=atmega2560 STATS_SUMSQ_BASE=256
Starting serial connect
Printer is not ready
The klippy host software is attempting to connect. Please
retry in a few moments.
Configured MCU 'z' (660 moves)
Loaded MCU 'z' 60 commands (v0.6.0-61-gf70fefa-20180508_003820-octopi / gcc: (GCC) 4.8.1 binutils: (GNU Binutils) 2.24)
MCU 'z' config: ADC_MAX=1023 PWM_MAX=255 CLOCK_FREQ=16000000 SOFT_PWM_MAX=256 SERIAL_BAUD=250000 MCU=atmega2560 STATS_SUMSQ_BASE=256
Starting heater checks for heater_bed
Starting heater checks for extruder
Calculating bed tilt with: [[10.0, 21.001101, 1.7453849999999997], [10.000000000000014, 210.000988, 1.7766849999999994], [281.99958549999997, 102.99859949999998, 2.1150379999999993]]
Coordinate descent best_err: 6.10538462332e-11 rounds: 194
Calculated bed tilt parameters: {'y_adjust': 0.00016561416593453346, 'x_adjust': 0.0013090986005706738, 'z_adjust': 1.7288196517978136}
Calculating bed tilt with: [[10.0, 21.001101, 1.7510189999999997], [10.000000000000014, 210.000988, 1.7491409999999994], [281.99958549999997, 102.99859949999998, 2.5003409999999993]]
Coordinate descent best_err: 7.54491262732e-11 rounds: 194
Calculated bed tilt parameters: {'y_adjust': -9.922398647434168e-06, 'x_adjust': 0.0027578253110784605, 'z_adjust': 1.7236491341729392}
Calculating bed tilt with: [[10.0, 21.001101, 1.7363079999999997], [10.000000000000014, 210.000988, 1.7694859999999997], [281.99958549999997, 102.99859949999998, 3.3635949999999992]]
Coordinate descent best_err: 1.11295973795e-10 rounds: 198
Calculated bed tilt parameters: {'y_adjust': 0.00017557740343542778, 'x_adjust': 0.005929723182174362, 'z_adjust': 1.6733261442817302}
Comments